S2K Commerce - Products Dropdown
S2K Commerce - Order Entry
Suzuki Outboard Parts
Shop OEM and aftermarket Suzuki outboard parts for DF-series FourStroke engines. Find repair, service, lower unit, fuel and engine rebuild parts.
Pro Marine USA carries Suzuki outboard engine parts for maintenance, troubleshooting, repair, and complete rebuild projects. Browse parts by engine system, or use your model, horsepower, serial number, or OEM part number whenever possible to confirm fitment before ordering.
Shop Suzuki Outboard Parts by System
- Control Cables & Boxes
- Cooling System
- Electrical System
- Engine Oil
- Fuel & Carburetion System
- Intake System
- Internal Engine Components
- Lower Unit Components
- Oiling System
- Paints
- Service & Oil Change Kits
- Service Manuals
- Steering Systems
- Transom & Midsection
- Trim System
Find the Correct Suzuki Outboard Part
Suzuki outboard parts can vary by model, horsepower, production range, and engine family. If you are unsure which component fits your engine, use the OEM parts lookup to locate the original Suzuki part number from a factory parts diagram.
Once you have the OEM part number, search Pro Marine to find available genuine Suzuki and aftermarket replacement options.
Use Our OEM Parts Lookup »Common Suzuki Outboard Engine Families
Pro Marine supports many popular Suzuki DF-series outboards across a wide horsepower range. Always confirm the exact engine model and identification information before ordering parts.
- Portable and Midrange: Suzuki DF2.5 through DF60 FourStroke applications
- Inline Four-Cylinder: common DF70 through DF140 engine families
- Mid- and High-Horsepower: DF150, DF175, DF200, DF225, and DF250 applications
- High-Horsepower Offshore: DF300, DF325, and DF350 platforms
- FourStroke EFI: electronically fuel-injected Suzuki outboards across most modern DF-series applications
Common Suzuki Outboard Repair Areas
- Engine overheating: inspect the water pump, impeller, thermostat, cooling passages, pressure-control components, and engine anodes.
- Hard starting or rough running: inspect fuel pumps, filters, injectors, spark plugs, ignition components, sensors, and intake sealing.
- Charging or electrical problems: inspect ignition coils, rectifier/regulators, sensors, wiring, grounds, and charging-system components.
- Low compression or power loss: inspect pistons, rings, cylinder condition, valves, bearings, gaskets, and internal engine components.
- Lower unit noise or water intrusion: inspect prop shaft seals, driveshaft seals, shift shaft seals, bearings, gears, and gear lube condition.
- Trim or steering problems: inspect trim motors, hydraulic components, steering systems, hoses, seals, and related rigging parts.
Why Buy Suzuki Outboard Parts from Pro Marine USA?
- OEM Suzuki and aftermarket replacement options for many common applications.
- Parts for routine maintenance, professional repair, complete engine rebuilds, lower units, fuel systems, electrical systems, steering, and trim.
- OEM diagram and part-number lookup tools to help identify the correct component before ordering.
- Dealer pricing available for qualified marine repair businesses and dealers.
- Large selection of Suzuki service kits, engine parts, lower unit components, cooling parts, and fuel system products.
- Fast weekday shipping on qualifying in-stock orders.
Frequently Asked Questions
How do I find the correct Suzuki outboard part?
Start with the engine model, horsepower, production information, and any available serial or identification numbers. Use the OEM parts lookup to identify the original Suzuki part number whenever possible.
Can I search Suzuki parts by OEM part number?
Yes. Enter the Suzuki OEM part number into the Pro Marine site search to locate available OEM and aftermarket replacement options. If you do not know the part number, use the OEM parts lookup first.
Do Suzuki outboard parts vary by model and year?
Yes. Suzuki may use different components across engines with similar horsepower depending on model, engine family, and production range. Confirm the complete engine identification information before ordering.
Do you carry parts for Suzuki DF300, DF325, and DF350 outboards?
Yes. Pro Marine carries parts for many Suzuki high-horsepower DF-series applications, including routine maintenance, cooling, fuel, electrical, internal engine, lower unit, steering, and trim components.
Do you carry both OEM and aftermarket Suzuki parts?
Yes. Pro Marine offers genuine Suzuki parts along with aftermarket replacement parts for many common Suzuki outboard maintenance, repair, and rebuild applications.
What Suzuki outboard parts are commonly replaced during routine maintenance?
Common maintenance items include engine oil, oil filters, fuel filters, spark plugs, water pump kits, impellers, thermostats, gear lube, drain plug seals, anodes, and model-specific service kit components.
Fitment Tip: Suzuki parts can vary by model, engine family, and production range. Confirm the OEM part number or complete engine identification information whenever possible before ordering.
13251-91J00
13371-91J00
5036188
5036198
5036204
0437680
0503948
0503948
0503952
0507174
0507174
0765850
0765873
0765913
33-932C
33-932S
503948
765913
09168-12012
5030465
769124
5032930
55321-90J00
55321-90J01
15200-87J00
15200-87J10
15200-99E00
5030700
5031399
5032617
769462
31173-96300
31173-96301
5032338
Pro Marine Aftermarket Water Pump Service
Pro Marine 3242P Impeller Repair Kit - Suzuki and Johnson/Evinrude Outboards
The Pro Marine 3242P Impeller Repair Kit is an aftermarket water pump service kit associated with select Suzuki and Johnson/Evinrude outboard applications. It is cross referenced to Suzuki water pump repair kit numbers in the 17400-96350 through 17400-96404 families and Johnson/Evinrude references including 778317, 5031415, 5031744, 5032166 and 5034358.
The supplied application information covers several Suzuki and Johnson/Evinrude engine families, including four-stroke and DT-series outboards. Because different engines use different water pump housings, customers should use the engine-specific compatibility information below to identify the correct components.
This listing is for Pro Marine aftermarket item 3242P, not a Genuine OEM Suzuki or Johnson/Evinrude kit.
Product Information
- Part Number: 3242P
- Brand: Pro Marine
- Product: Impeller Repair Kit
- Product Type: Aftermarket Water Pump Service Kit
- Application: Select Suzuki and Johnson/Evinrude Outboards
- System: Lower Unit Cooling Water Pump
- Primary OEM References: 778317, 0778317
- Additional OEM References: 5031415, 5031744, 5032166, 5034358
- Additional Cross Reference: 8M6012809
OEM and Cross Reference Numbers
Use these numbers to help identify the applicable water pump service kit. Cross-reference numbers do not mean that every engine or housing configuration is interchangeable.
| Brand / Reference | Part Numbers |
|---|---|
| Pro Marine | 3242P |
| Johnson/Evinrude | 0778317, 778317, 5031415, 5031744, 5032166, 5034358 |
| Suzuki | 17400-96350, 17400-96351, 17400-96352, 17400-96353, 17400-96354 |
| Suzuki | 17400-96400, 17400-96401, 17400-96402, 17400-96403, 17400-96404 |
| Additional Reference | 8M6012809 |
What This Part Is Used For
The outboard water pump uses a rotating impeller to move cooling water through the engine. Water pump components are subject to wear, and damaged or deteriorated parts can reduce cooling performance.
An impeller repair kit is used during water pump maintenance or repair. Depending on the engine and the contents of the selected kit, additional housing components may also be required.
- Routine water pump maintenance
- Replacement of worn water pump components
- Service following an impeller failure
- Cooling system repairs
- Lower unit water pump inspection and rebuilding
Important Fitment and Housing Information
The supplied application data includes multiple Suzuki and Johnson/Evinrude water pump housing families. The housing required depends on the exact engine model and production configuration.
Do not select a housing based only on horsepower. Verify the complete engine model and OEM water pump diagram before ordering.
The housing references below are organized according to the supplied housing-specific application lists. They are not represented as interchangeable parts.
Suzuki Outboard Applications
Suzuki Four-Stroke Applications
| HP | Engine Model | Years | Housing Reference |
|---|---|---|---|
| 25 | DF25 | 2000-2005 | 17410-92L00 |
| 25 | DF25Q, DF25Q(QR), DF25T | 2000-2007 | 17410-92L00 |
| 30 | DF30 | 2000-2006 | 17410-92L00 |
| 30 | DF30Q, DF30Q(QR), DF30T | 2000-2007 | 17410-92L00 |
| 40 | DF40 | 1999-2010 | 17410-92L00 / 17410-95D20 |
| 40 | DF40QH, DF40TL | 1999-2007 | 17410-92L00 / 17410-95D20 |
| 50 | DF50 | 1999-2010 | 17410-92L00 / 17410-95D20 |
| 50 | DF50QH, DF50TL | 1999-2007 | 17410-92L00 / 17410-95D20 |
| 90 | DF90 | 2001-2008 | 17400-90812 |
| 90 | DF90TL | 2001-2007 | 17400-90812 |
| 100 | DF100 | 2009-2010 | 17400-90812 |
| 115 | DF115 | 2001-2010 | 17400-90812 |
| 115 | DF115TL | 2001-2007 | 17400-90812 |
| 140 | DF140, DF140T, DF140Z | 2002-2010 | 17400-90812 |
Suzuki DT-Series Applications
| HP | Model | Years | Housing References |
|---|---|---|---|
| 25 | DT25C | 1989-2000 | 17410-95D20 |
| 30 | DT30C | 1989-2000 | 17410-95D20 |
| 40 | DT40C | 1986-1998 | 17410-92L00 |
Johnson and Evinrude Applications
The following model numbers were supplied as applications associated with the listed housing and water pump service references. Confirm the complete model before ordering.
| HP | Engine Family | Compatible Model Numbers |
|---|---|---|
| 25 | Evinrude E25 | E25EL4SIC, E25EL4SSS, E25PL4SIC, E25PL4SSS, E25R4SIC, E25R4SSS, E25RL4SIC, E25RL4SSS, E25TE4SIC, E25TE4SSS, E25TEL4SIC, E25TEL4SSS |
| 25 | Johnson J25 | J25PL4SOC, J25PL4SRS, J25TEL4SOC, J25TEL4SRS |
| 30 | Evinrude E30 | E30EL4SIC, E30EL4SSS, E30PL4SIC, E30PL4SSS, E30R4SIC, E30R4SSS, E30RL4SIC, E30RL4SSS, E30TE4SIC, E30TE4SSS, E30TEL4SIC, E30TEL4SSS |
| 30 | Johnson J30 | J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SOC, J30TEL4SRS, J30TEL4SUA |
| 40 | Evinrude E40 | E40PL4EES, E40PL4SIR, E40PL4SSC |
| 40 | Johnson J40 / BJ40 | J40PL4SDE, J40PL4SNF, J40PL4SOB, J40PL4SRM, J40PL4STC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS |
| 50 | Evinrude E50 | E50PL4EES, E50PL4SIR, E50PL4SSC |
| 50 | Johnson J50 / BJ50 | J50PL4SDE, J50PL4SNF, J50PL4SOB, J50PL4SRM, J50PL4STC, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS |
| 90 | Johnson J90 / BJ90 | J90PL4SDA, J90PL4SOR, J90PL4SRC, J90PL4STS, J90PX4SDA, J90PX4SOR, J90PX4SRC, J90PX4STS, BJ90PL4SDA, BJ90PL4SOR, BJ90PL4SRC, BJ90PL4STS, BJ90PX4SDA, BJ90PX4SOR, BJ90PX4SRC, BJ90PX4STS |
| 115 | Johnson J115 / BJ115 | J115PL4SDA, J115PL4SOR, J115PL4SRC, J115PL4STS, J115PX4SDA, J115PX4SOR, J115PX4SRC, J115PX4STS, BJ115L4SRC, BJ115L4STS, BJ115PL4SDA, BJ115PL4SOR, BJ115PX4SDA, BJ115PX4SOR, BJ115X4SRC, BJ115X4STS |
| 140 | Johnson J140 / BJ140 | J140CX4SDA, J140CX4SOR, J140CX4SRC, J140CX4STS, J140PL4SDA, J140PL4SOR, J140PL4SRC, J140PL4STS, J140PX4SDA, J140PX4SOR, J140PX4SRS, J140PX4STS, BJ140CX4DR, BJ140CX4SOC, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SOC, BJ140PL4SRS, BJ140PX4SOC, BJ140PX4SRS, BJ140X4SDR |
Water Pump Housing Selection and Related Parts
The following housing references were supplied for the engine families above. These are separate components and should be selected by the exact engine application.
Genuine Johnson/Evinrude OEM
17400-90812 Water Pump Housing
Applications: Suzuki DF90, DF100, DF115 and DF140 four-stroke outboards and specified Johnson/Evinrude 90, 115 and 140 HP four-stroke models.
Suzuki years: DF90 2001-2008, DF100 2009-2010, DF115 2001-2010, DF140 2002-2010, including the specified TL, T and Z variants.
Housing Cross References: 0769573, 17400-90810, 17400-90811, 17400-90812, 17411-90J00, 5033716.
View OEM 17400-90812 HousingSuzuki OEM Housing Reference - Special Order
17410-92L00 Water Pump Housing
Applications: Select Suzuki DF25, DF30, DF40 and DF50 four-stroke engines, Suzuki DT40C, and specified Johnson/Evinrude 25-50 HP four-stroke models.
OEM References: 17410-94431, 17410-94430, 17410-94410, 17411-94421, 17411-94420, 17411-94400.
Availability: Special order. Contact Pro Marine USA to confirm availability and the correct replacement number.
Request Housing 17410-92L00Suzuki OEM Housing Reference - Special Order
17410-95D20 Water Pump Housing
Applications: Select Suzuki DF40 and DF50 four-stroke engines, DT25C and DT30C two-stroke engines, and specified Johnson/Evinrude 40-50 HP four-stroke models.
OEM References: 17410-95D20, 17410-95D11, 17410-95D10, 17410-95D00, 5031416, 0769667.
Availability: Special order. Contact Pro Marine USA to confirm availability and compatibility.
Request Housing 17410-95D20What is Included
Pro Marine 3242P is sold as an impeller repair kit. The exact individual components and quantities were not supplied for this listing, so customers should confirm the current kit contents before ordering.
Water pump housings: The three housing references shown above are listed separately and are not represented as included components of 3242P.
Engine oil: Not included.
Gear lube: Not included.
Marine technicians can use the application and housing information on this page to identify additional components needed for a particular water pump repair.
Installation and Water Pump Service Tips
- Confirm the correct kit and housing using the complete engine model and OEM parts diagram.
- Follow the manufacturer's lower-unit removal and water pump service procedures.
- Inspect the existing water pump housing for scoring, distortion or damage.
- Check the impeller, pump plate, seals and mating surfaces.
- Remove damaged components and debris before reassembly.
- Install replacement parts in the correct orientation.
- Use factory tightening specifications and approved lubricants where directed.
- After reassembly, verify cooling water circulation and monitor engine temperature.
Never operate an outboard without an adequate cooling water supply. Running the engine dry can damage the water pump impeller and cause engine overheating.
Key Features and Benefits
- Pro Marine Aftermarket: Marine water pump service product supplied under the Pro Marine line.
- OEM Cross References: Searchable replacement references for Suzuki and Johnson/Evinrude applications.
- Engine-Specific Fitment: Detailed Suzuki and Johnson/Evinrude model information.
- Housing Identification: Separate water pump housing references organized by engine family.
- Service Application: Intended for water pump maintenance and repair on compatible outboards.
Frequently Asked Questions
Is Pro Marine 3242P a Genuine OEM kit?
No. Pro Marine 3242P is an aftermarket impeller repair kit.
What OEM numbers cross reference 3242P?
Supplied references include 0778317, 778317, 5031415, 5031744, 5032166, 5034358, 8M6012809 and the Suzuki 17400-96350 through 17400-96404 repair kit number families.
Does this kit fit Suzuki DF25 and DF30?
The supplied application information includes DF25 and DF30 models and variants from 2000-2007, with model-specific year distinctions. Confirm the required repair kit against the engine diagram.
Does this kit fit Suzuki DF40 and DF50?
The supplied application information includes DF40 and DF50 four-stroke models from 1999-2010 and specified QH and TL variants from 1999-2007.
Does this kit fit Suzuki DF90, DF115 and DF140?
The supplied housing application data includes these engine families under water pump housing 17400-90812. Confirm that 3242P is the correct impeller repair kit for the exact engine before ordering.
Does this kit fit Suzuki DT25C, DT30C and DT40C?
These models appear in the supplied application information. DT25C and DT30C are listed for 1989-2000, while DT40C is listed for 1986-1998. Verify the required kit by model and year.
Does this kit fit Johnson and Evinrude outboards?
The supplied application information includes specified Johnson/Evinrude 25, 30, 40, 50, 90, 115 and 140 HP models. Use the complete model numbers in the fitment chart.
Does the kit include a water pump housing?
Housing inclusion has not been confirmed. The housing references on this page are identified as separate components.
Which water pump housing should I use?
Housing selection depends on the engine. The supplied references include 17400-90812, 17410-92L00 and 17410-95D20. Verify the correct housing through the OEM parts diagram.
Is 17400-90812 the same as 17410-95D20?
No. These are different housing references associated with different application groups. They should not be treated as interchangeable without manufacturer confirmation.
When should I replace my water pump impeller?
Follow the engine manufacturer's recommended maintenance schedule. Inspect the water pump whenever cooling performance is in question or the lower unit is being serviced.
Can I reuse the existing water pump housing?
That depends on its condition and the manufacturer's service specifications. Inspect the housing for damage, scoring and excessive wear before reuse.
How can I confirm the correct repair kit?
Match the complete engine model and production information to the manufacturer's water pump parts diagram. Pro Marine USA can assist with identifying the correct components.
Dealer Discounts & Store Policies
Wholesale Marine Parts Pricing
Pro Marine USA supplies OEM and aftermarket marine engine parts to repair shops, dealerships, professional technicians and retail customers.
Qualified marine businesses can apply for a dealer account to access wholesale pricing on eligible products.
Shipping Information
- Free shipping on qualifying orders over $100 within the continental United States. Oil and oversized items are excluded.
- In-stock orders placed before 5:30 PM EST ship the same business day, Monday-Friday.
- Shipping options include UPS, USPS and FedEx.
- Typical delivery is 1-5 business days, depending on destination and shipping service.
30-Day Return Policy
- Eligible returns are accepted within 30 days.
- Maintenance kits must be new, unused and in original packaging.
- Installed parts are not returnable.
- Return authorization is required before returning merchandise.
Need Help Confirming Fitment?
Contact Pro Marine USA with your engine model and identification information for assistance selecting the correct water pump repair components.
Contact Pro Marine USA or call 941-721-3000.
Searchable Part Numbers
3242P, 0778317, 778317, 5031415, 5031744, 5032166, 5034358, 8M6012809, 17400-96350, 17400-96351, 17400-96352, 17400-96353, 17400-96354, 17400-96400, 17400-96401, 17400-96402, 17400-96403, 17400-96404, 17400-90812, 17410-92L00, 17410-95D20
Searchable Terms
Pro Marine 3242P impeller repair kit, Suzuki outboard impeller kit, Johnson Evinrude impeller repair kit, Suzuki DF25 water pump kit, Suzuki DF30 water pump kit, Suzuki DF40 water pump kit, Suzuki DF50 water pump kit, Suzuki DF90 water pump housing, Suzuki DF100 water pump housing, Suzuki DF115 water pump housing, Suzuki DF140 water pump housing, Suzuki DT25C impeller, Suzuki DT30C impeller, Suzuki DT40C impeller, Johnson Evinrude 25 HP four-stroke, Johnson Evinrude 30 HP four-stroke, Johnson Evinrude 40 HP four-stroke, Johnson Evinrude 50 HP four-stroke, Johnson Evinrude 90 HP four-stroke, Johnson Evinrude 115 HP four-stroke, Johnson Evinrude 140 HP four-stroke, Suzuki water pump repair, marine outboard cooling system service, aftermarket impeller repair kit
17400-96350
17400-96351
17400-96352
17400-96353
17400-96354
17400-96400
17400-96401
17400-96402
17400-96403
17400-96404
5031415
5031744
5032166
5034358
778317
8M6012809
17400-87E01
17400-87E02
17400-87E03
17400-87E04
8M6012818
F187787Q3
F197787
F197787-1
F197787-2
F197787-3
F197787Q3
F197787T3
F1977871
F1977872
F1977873
822352A1
9-38013
9-38006
99105-00192
99105-99100
Power Trim & Tilt Cap with Seals
Replacement Tilt Cap Assembly for Select Yamaha, Suzuki & OMC Showa Trim Systems
This replacement tilt cap with seals assembly fits select Yamaha, Suzuki, Johnson, and Evinrude outboards using compatible Showa power trim and tilt systems.
The tilt cap assembly helps seal the hydraulic trim cylinder while supporting proper trim piston movement, hydraulic pressure retention, and reliable trim and tilt operation.
Compatible Applications
| Brand | Model Range | Years | System |
|---|---|---|---|
| Yamaha | 115HP | 1997-2007 | Showa Power Trim & Tilt |
| Yamaha | 115HP FourStroke | 2000-2007 | Showa Power Trim & Tilt |
| Yamaha | 130HP | 1997-2004 | Showa Power Trim & Tilt |
| Yamaha | 150HP | 1997-2007 | Showa Power Trim & Tilt |
| Yamaha | 150HP FourStroke | 2004-2007 | Showa Power Trim & Tilt |
| Yamaha | 175HP | 1997-2007 | Showa Power Trim & Tilt |
| Yamaha | 200HP | 1997-2005 | Showa Power Trim & Tilt |
| Yamaha | 225HP | 1997-2007 | Showa Power Trim & Tilt |
| Yamaha | 250HP | 2003-2007 | Showa Power Trim & Tilt |
| Yamaha | 300HP | 2004-2007 | Showa Power Trim & Tilt |
| Suzuki | DF115 | 2015-2024 | Showa Power Trim & Tilt |
| Suzuki | DF140 | 2002-2021 | Showa Power Trim & Tilt |
| Suzuki | DF150 | 2006-2023 | Showa Power Trim & Tilt |
| Suzuki | DF175 | 2006-2023 | Showa Power Trim & Tilt |
| Suzuki | DF200 | 2015-2024 | Showa Power Trim & Tilt |
| Johnson / Evinrude | 70-235HP | 1978-1983 | Showa Power Trim & Tilt |
| Johnson / Evinrude | 140HP FourStroke | 2003-2006 | Showa Power Trim & Tilt |
Because manufacturers used multiple trim system variations depending on model and production range, always verify your engine model, serial number, and trim cylinder diagram before ordering.
OEM Part Numbers & Cross References
| Brand | OEM Part Number |
|---|---|
| Yamaha | 63P-43810-00-00 |
| Yamaha | 63P-43810-09-00 |
| Yamaha | 64E-43810-00-00 |
| Yamaha | 64E-43810-09-00 |
| Yamaha | 64E-43811-01-00 |
| Yamaha | 64E-43811-02-00 |
| Suzuki | 48401-92J00 |
| Suzuki | 48401-92J01 |
| Suzuki | 48401-96J00 |
| Suzuki | 48401-96J01 |
| Suzuki | 48401-96J02 |
| Johnson / Evinrude | 5033932 |
| Johnson / Evinrude | 390006 |
| Johnson / Evinrude | 768745 |
What This Tilt Cap Assembly is Used For
This trim cap assembly is used in compatible hydraulic power trim and tilt systems to support the trim piston and help maintain proper hydraulic sealing.
The cap and seal assembly helps retain hydraulic pressure while allowing smooth piston movement during trim and tilt operation.
Worn or damaged trim caps and seals may cause hydraulic leaks, weak trim performance, erratic movement, or difficulty holding trim position.
Replacing worn hydraulic trim seals and cap components can help restore proper trim operation and reduce hydraulic fluid leakage.
Key Features and Benefits
- Replacement tilt cap assembly with seals
- Fits select Yamaha, Suzuki, Johnson, and Evinrude outboards
- Compatible with Showa hydraulic trim systems
- Helps maintain hydraulic trim pressure
- Supports proper trim piston operation
- Helps reduce hydraulic fluid leakage
- Common repair item during trim cylinder service
- Sold individually
Trim Cap Assembly Details
- Part Type: Tilt Cap with Seals
- Application: Hydraulic Power Trim & Tilt Systems
- System Type: Showa Hydraulic Trim System
- Fits Brands: Yamaha, Suzuki, Johnson, Evinrude
- Use: Trim cylinder sealing and piston support
- Quantity Sold: Each
FAQ
What does this trim cap fit?
This trim cap assembly fits select Yamaha, Suzuki, Johnson, and Evinrude outboards using compatible Showa power trim and tilt systems.
Does this include seals?
Yes. This assembly includes the cap and sealing components used in compatible hydraulic trim systems.
Can a bad trim cap cause hydraulic leaks?
Yes. Damaged cap seals can allow hydraulic fluid leakage and may affect trim and tilt performance.
Should I verify my trim assembly before ordering?
Yes. Manufacturers used several trim system variations depending on model and serial range, so diagram verification is recommended.
Is this used on Showa trim systems?
Yes. This part is designed for compatible Showa-style hydraulic trim and tilt assemblies used across multiple marine brands.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 continental U.S.
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1–5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Hydraulic trim components should be installed only after confirming correct fitment.
- Items must be new, unused, and in original packaging.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Terms
63P438, tilt cap with seals, Yamaha trim cap, Suzuki trim cap, Johnson trim cap, Evinrude trim cap, Showa trim cap, hydraulic trim cap, power trim seal cap, Yamaha 63P-43810-00-00, Yamaha 64E-43810-00-00, Suzuki 48401-96J02, Suzuki 48401-92J01, Johnson 5033932, Evinrude 390006, OMC 768745, hydraulic trim seal assembly, trim cylinder cap assembly
48401-92J00
48401-92J00
48401-92J01
48401-96J00
48401-96J01
48401-96J02
5033932
63P-43810-00-00
63P-43810-09-00
64E-43810-00-00
64E-43810-09-00
64E-43811-01-00
64E-43811-02-00
48630-92J00
48630-94900
48630-96J01
48630-96J02
48630-96J03
48630-96J04
5030870
5033935
56115-ZW1-702
64E-43820-00-00
64E-43820-08-00
64E-43820-09-00
64E-43821-00-00
64E-43821-01-00
64E-43821-02-00
64E-43821-03-00
64E-43821-04-00
64E-43821-05-00
64E-43821-08-00
64E-43821-09-00