Z6_GHK6HJC0OG6S20Q8HU3K6R0G63
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM5
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM7
Z7_GHK6HJC0OG6S20Q8HU3K6R0Q22

Suzuki Outboard Parts

Shop OEM and aftermarket Suzuki outboard parts for DF-series FourStroke engines. Find repair, service, lower unit, fuel and engine rebuild parts.

Pro Marine USA carries Suzuki outboard engine parts for maintenance, troubleshooting, repair, and complete rebuild projects. Browse parts by engine system, or use your model, horsepower, serial number, or OEM part number whenever possible to confirm fitment before ordering.

Shop Suzuki Outboard Parts by System

Find the Correct Suzuki Outboard Part

Suzuki outboard parts can vary by model, horsepower, production range, and engine family. If you are unsure which component fits your engine, use the OEM parts lookup to locate the original Suzuki part number from a factory parts diagram.

Once you have the OEM part number, search Pro Marine to find available genuine Suzuki and aftermarket replacement options.

Use Our OEM Parts Lookup »

Common Suzuki Outboard Engine Families

Pro Marine supports many popular Suzuki DF-series outboards across a wide horsepower range. Always confirm the exact engine model and identification information before ordering parts.

  • Portable and Midrange: Suzuki DF2.5 through DF60 FourStroke applications
  • Inline Four-Cylinder: common DF70 through DF140 engine families
  • Mid- and High-Horsepower: DF150, DF175, DF200, DF225, and DF250 applications
  • High-Horsepower Offshore: DF300, DF325, and DF350 platforms
  • FourStroke EFI: electronically fuel-injected Suzuki outboards across most modern DF-series applications

Common Suzuki Outboard Repair Areas

  • Engine overheating: inspect the water pump, impeller, thermostat, cooling passages, pressure-control components, and engine anodes.
  • Hard starting or rough running: inspect fuel pumps, filters, injectors, spark plugs, ignition components, sensors, and intake sealing.
  • Charging or electrical problems: inspect ignition coils, rectifier/regulators, sensors, wiring, grounds, and charging-system components.
  • Low compression or power loss: inspect pistons, rings, cylinder condition, valves, bearings, gaskets, and internal engine components.
  • Lower unit noise or water intrusion: inspect prop shaft seals, driveshaft seals, shift shaft seals, bearings, gears, and gear lube condition.
  • Trim or steering problems: inspect trim motors, hydraulic components, steering systems, hoses, seals, and related rigging parts.

Why Buy Suzuki Outboard Parts from Pro Marine USA?

  • OEM Suzuki and aftermarket replacement options for many common applications.
  • Parts for routine maintenance, professional repair, complete engine rebuilds, lower units, fuel systems, electrical systems, steering, and trim.
  • OEM diagram and part-number lookup tools to help identify the correct component before ordering.
  • Dealer pricing available for qualified marine repair businesses and dealers.
  • Large selection of Suzuki service kits, engine parts, lower unit components, cooling parts, and fuel system products.
  • Fast weekday shipping on qualifying in-stock orders.

Frequently Asked Questions

How do I find the correct Suzuki outboard part?

Start with the engine model, horsepower, production information, and any available serial or identification numbers. Use the OEM parts lookup to identify the original Suzuki part number whenever possible.

Can I search Suzuki parts by OEM part number?

Yes. Enter the Suzuki OEM part number into the Pro Marine site search to locate available OEM and aftermarket replacement options. If you do not know the part number, use the OEM parts lookup first.

Do Suzuki outboard parts vary by model and year?

Yes. Suzuki may use different components across engines with similar horsepower depending on model, engine family, and production range. Confirm the complete engine identification information before ordering.

Do you carry parts for Suzuki DF300, DF325, and DF350 outboards?

Yes. Pro Marine carries parts for many Suzuki high-horsepower DF-series applications, including routine maintenance, cooling, fuel, electrical, internal engine, lower unit, steering, and trim components.

Do you carry both OEM and aftermarket Suzuki parts?

Yes. Pro Marine offers genuine Suzuki parts along with aftermarket replacement parts for many common Suzuki outboard maintenance, repair, and rebuild applications.

What Suzuki outboard parts are commonly replaced during routine maintenance?

Common maintenance items include engine oil, oil filters, fuel filters, spark plugs, water pump kits, impellers, thermostats, gear lube, drain plug seals, anodes, and model-specific service kit components.

Fitment Tip: Suzuki parts can vary by model, engine family, and production range. Confirm the OEM part number or complete engine identification information whenever possible before ordering.

|◀ ◀ 805 - 816 of 1065 ▶ ▶|
View:
Heat Shrinkable 16-14 Gauge
Item#:
BPB
Manufacturer:
Pacer Wire & Connectors
Available:
In Stock
Your Price:
17.85
25 PACK
Heavy Gauge Battery Cable Splice Connector for Boats and Marine Rigging

Marine Battery Cable and Electrical Rigging

2 Gauge Battery Cable Butt Connector - 2 AWG Marine Cable Splice

The 2BC Battery Cable Butt Connector is designed for joining two sections of 2 gauge (2 AWG) battery cable. This heavy-gauge electrical connector is used for battery cable repairs, cable extensions and custom marine electrical installations.

Whether repairing an existing battery cable or building a custom cable assembly, a properly installed butt connector provides a mechanical and electrical connection between two cable ends.

The 2BC connector can be used with compatible 2 AWG red or black battery cable. For marine applications, the completed connection should be protected with appropriately sized marine-grade heat-shrink tubing to help prevent moisture intrusion and corrosion.

Pro Marine USA also carries matching 2 gauge battery cable and 1/2-inch heat shrink in red, black and combination packs, making it easy to purchase the materials needed for your battery cable installation.

Product Information

  • Item Number: 2BC
  • Product: Battery Cable Butt Connector
  • Cable Size: 2 Gauge / 2 AWG
  • Connector Type: Butt Splice Connector
  • Application: Battery Cable Splicing and Repair
  • Compatible Cable: 2 AWG Battery Cable
  • Connection Type: Crimped Cable Splice
  • Installation: Requires an appropriate heavy-duty cable crimping tool
  • Recommended Protection: Compatible Marine-Grade Heat Shrink
  • Typical Uses: Marine Battery Cables, Electrical Rigging and Cable Repairs

What This Part Is Used For

The 2BC butt connector is used to join two sections of 2 AWG battery cable when repairing, extending or assembling heavy-gauge electrical wiring.

Marine battery cables carry significant electrical current. Connections must be properly sized, securely crimped and protected against moisture and corrosion.

Common Applications

  • Marine battery cable repairs
  • Joining two sections of 2 AWG battery cable
  • Custom battery cable fabrication
  • Boat electrical system rigging
  • Battery cable extensions where permitted by the installation requirements
  • Battery switch and distribution wiring repairs
  • Marine engine battery cable service
  • Other compatible heavy-gauge DC electrical installations

This connector is not engine-specific. Compatibility is determined primarily by the cable gauge, conductor construction and electrical installation requirements.

Compatible Battery Cable

The 2BC connector is intended for use with compatible 2 gauge battery cable. Pro Marine USA offers the following matching cable options.

Item Description Cable Size Color Product
2B Battery Cable - Black 2 AWG Black View Cable
2R Battery Cable - Red 2 AWG Red View Cable

Build or Repair Your 2 Gauge Battery Cable

Complete your battery cable installation with compatible 2 AWG cable and heat-shrink tubing available from Pro Marine USA.

Matching 2 AWG Battery Cable

2B - 2 Gauge Black Battery Cable

Black 2 AWG battery cable for compatible marine battery and electrical wiring installations. Commonly used for negative battery cable connections.

Shop 2 Gauge Black Cable

Matching 2 AWG Battery Cable

2R - 2 Gauge Red Battery Cable

Red 2 AWG battery cable for compatible marine battery and electrical wiring installations. Commonly used for positive battery cable connections.

Shop 2 Gauge Red Cable

Recommended Heat Shrink for Battery Cable Connections

After crimping a battery cable butt connector, protect the completed splice with properly sized marine-grade heat-shrink tubing.

Heat shrink helps provide electrical insulation, strain relief and protection from moisture when the tubing is appropriate for the application and correctly installed.

Item Description Color Product Link
12RB 1/2-Inch Heat Shrink - Red and Black Combination Red and Black View Heat Shrink
12R 1/2-Inch Red Heat Shrink - 1 Foot Red View Heat Shrink
12B 1/2-Inch Black Heat Shrink - 1 Foot Black View Heat Shrink

Important: Verify that the heat-shrink tubing has the appropriate expanded diameter, recovered diameter and environmental rating for the completed splice. A nominal 1/2-inch size alone does not establish fit.

How to Install a 2 Gauge Battery Cable Butt Connector

Proper installation is essential for a reliable heavy-gauge battery cable connection.

  1. Disconnect the battery. Isolate the electrical system before working on battery cables. Disconnect the negative connection first when appropriate for the installation.
  2. Measure and cut the cable. Determine the required cable length and cut the 2 AWG battery cable cleanly.
  3. Prepare the heat shrink. Slide an appropriately sized piece of heat-shrink tubing onto the cable before making the splice.
  4. Strip the cable insulation. Remove only enough insulation for the connector's required insertion depth. Avoid damaging the conductor strands.
  5. Insert the cable. Insert the stripped cable end fully into one side of the butt connector. Repeat with the second cable.
  6. Crimp the connector. Use a properly sized heavy-duty crimping tool and the crimping method specified for the connector and cable.
  7. Inspect the connection. Check that both cable ends are securely retained and the crimp is properly formed.
  8. Apply heat shrink. Center the tubing over the splice and shrink it according to the tubing manufacturer's instructions.
  9. Secure the cable. Support the completed assembly and protect it from abrasion, sharp edges and excessive movement.

Important Battery Cable Installation Information

Battery cables can carry very high current. Improperly installed connections can overheat, create excessive electrical resistance or cause electrical system failure.

  • Use only connectors approved for the cable size and conductor type.
  • Use the correct crimping tool and manufacturer-recommended crimp method.
  • Do not use ordinary pliers to crimp heavy-gauge battery cable connectors.
  • Do not rely on solder alone to secure a battery cable connection.
  • Protect the completed connection from moisture, abrasion and vibration.
  • Follow applicable marine electrical standards and equipment manufacturer requirements.
  • Use a continuous cable run where required by the engine or electrical system manufacturer.
  • Do not splice engine starting cables where the manufacturer prohibits splices.

For critical starting and high-current circuits, have the installation inspected by a qualified marine electrical technician when necessary.

Key Features and Benefits

  • 2 AWG Cable Compatibility: Designed for compatible 2 gauge battery cable connections.
  • Battery Cable Repair: Useful for joining or repairing heavy-gauge electrical cable.
  • Marine Electrical Applications: Suitable for appropriately specified boat battery and rigging installations.
  • Red or Black Cable: Can be used with compatible 2 AWG cable regardless of insulation color.
  • Crimp Connection: Designed to be installed using an appropriate heavy-duty cable crimping tool.
  • Heat-Shrink Protection: Can be protected with correctly sized external heat-shrink tubing.
  • Matching Products Available: Pro Marine USA carries 2 AWG cable and red, black and combination heat-shrink options.

Frequently Asked Questions

What size cable does the 2BC butt connector fit?

The 2BC butt connector is intended for compatible 2 gauge (2 AWG) battery cable. Confirm the connector and conductor dimensions before installation.

Can I use this connector on marine battery cables?

It can be used for appropriate marine battery cable splicing applications when the connector, cable, crimping method and environmental protection meet the installation requirements.

Can I use the same connector with red and black battery cable?

Yes. The connector is sized by cable gauge, not insulation color. It can be used with compatible 2 AWG red or black cable.

What black battery cable works with this connector?

Pro Marine USA offers 2B - 2 Gauge Black Battery Cable.

What red battery cable works with this connector?

Pro Marine USA offers 2R - 2 Gauge Red Battery Cable.

Do I need heat shrink when installing a battery cable butt connector?

For marine applications, properly selected heat-shrink tubing is recommended to insulate and protect the completed connection against moisture and corrosion.

What heat shrink can I purchase for this connector?

Pro Marine USA offers 1/2-inch heat shrink in red, black and combination packs. Confirm that the tubing will fit over the completed splice and recover tightly around the cable insulation.

Does this connector already have heat shrink attached?

This listing identifies a battery cable butt connector. Integrated heat shrink has not been confirmed. The heat-shrink products linked above are available separately.

Can I use regular pliers to crimp this connector?

No. Heavy-gauge battery cable connectors require an appropriate crimping tool and correctly matched dies or crimping method.

Can I extend an outboard engine battery cable with this connector?

Only where the engine manufacturer and applicable electrical installation requirements permit a spliced battery cable. Some engine starting circuits require continuous cable runs.

Is 2 AWG the same as 2/0 AWG?

No. 2 AWG and 2/0 AWG are different cable sizes. This connector is identified for 2 AWG cable, not 2/0 AWG cable.

Can this connector be used with 4 gauge or 6 gauge cable?

No. Use a connector specifically sized for the cable gauge being installed.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies OEM and aftermarket marine parts, electrical components, battery cables and rigging supplies to marine repair shops, dealerships, professional technicians and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on qualifying orders over $100 within the continental United States. Oil and oversized items are excluded.
  • In-stock orders placed before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options include UPS, USPS and FedEx.
  • Typical delivery is 1-5 business days, depending on destination and shipping service.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused and in original packaging.
  • Installed parts are not returnable.
  • OEM electrical components are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Selecting Battery Cable Components?

Contact Pro Marine USA for assistance identifying battery cable, electrical connectors, heat shrink and other marine rigging supplies.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

2BC, 2B, 2R, 12RB, 12R, 12B

Searchable Terms

2 gauge battery cable butt connector, 2 AWG battery cable splice, marine battery cable connector, boat battery cable butt splice, heavy gauge wire connector, 2 gauge wire splice connector, marine battery cable repair, battery cable extension connector, boat electrical rigging, marine electrical cable splice, 2 AWG red battery cable, 2 AWG black battery cable, marine battery cable heat shrink, 1/2 inch red heat shrink, 1/2 inch black heat shrink, marine battery cable fabrication, battery cable crimp connector, boat battery wiring connector, marine DC electrical connector

Item#:
2BC
Manufacturer:
Pro Marine
Available:
In Stock
20.3100
Your Price:
18.00
10 PACK
Heavy Gauge Battery Cable Splice Connector for Boats and Marine Rigging

Marine Battery Cable and Electrical Rigging

4 Gauge Battery Cable Butt Connector - 4 AWG Marine Cable Splice

The 4BC Battery Cable Butt Connector is designed for joining two sections of 4 gauge (4 AWG) battery cable. This heavy-gauge electrical connector is used for battery cable repairs, cable extensions and custom marine electrical installations.

Whether repairing an existing battery cable or building a custom cable assembly, a properly installed butt connector provides a mechanical and electrical connection between two cable ends.

The 4BC connector can be used with compatible 4 AWG red or black battery cable. For marine applications, the completed connection should be protected with appropriately sized marine-grade heat-shrink tubing to help prevent moisture intrusion and corrosion.

Pro Marine USA also carries matching 4 gauge battery cable and 1/2-inch heat shrink in red, black and combination packs, making it easy to purchase the materials needed for your battery cable installation.

Product Information

  • Item Number: 4BC
  • Product: Battery Cable Butt Connector
  • Cable Size: 4 Gauge / 4 AWG
  • Connector Type: Butt Splice Connector
  • Application: Battery Cable Splicing and Repair
  • Compatible Cable: 4 AWG Battery Cable
  • Connection Type: Crimped Cable Splice
  • Installation: Requires an appropriate heavy-duty cable crimping tool
  • Recommended Protection: Compatible Marine-Grade Heat Shrink
  • Typical Uses: Marine Battery Cables, Electrical Rigging and Cable Repairs

OEM and Cross Reference Numbers

The 4BC is a general-purpose battery cable connector rather than an engine-specific OEM replacement part. No additional manufacturer cross-reference numbers have been provided for this connector.

Item Number Description Application
4BC 4 Gauge Battery Cable Butt Connector 4 AWG Cable Splicing

What This Part Is Used For

The 4BC butt connector is used to join two sections of 4 AWG battery cable when repairing, extending or assembling heavy-gauge electrical wiring.

Marine battery cables can carry significant electrical current. Connections must be properly sized, securely crimped and protected against moisture and corrosion.

Common Applications

  • Marine battery cable repairs
  • Joining two sections of 4 AWG battery cable
  • Custom battery cable fabrication
  • Boat electrical system rigging
  • Battery cable extensions where permitted by the installation requirements
  • Battery switch and distribution wiring repairs
  • Marine engine battery cable service
  • Other compatible heavy-gauge DC electrical installations

This connector is not engine-specific. Compatibility is determined primarily by the cable gauge, conductor construction and electrical installation requirements.

Compatible Battery Cable Applications

The 4BC connector is intended for use with compatible 4 gauge battery cable. Pro Marine USA offers the following matching cable options.

Item Description Cable Size Color Product
4B Battery Cable - Black 4 AWG Black View Cable
4R Battery Cable - Red 4 AWG Red View Cable

Build or Repair Your 4 Gauge Battery Cable

Complete your battery cable installation with compatible 4 AWG cable and heat-shrink tubing available from Pro Marine USA.

Matching 4 AWG Battery Cable

4B - 4 Gauge Black Battery Cable

Black 4 AWG battery cable for compatible marine battery and electrical wiring installations. Commonly used for negative battery cable connections.

Shop 4 Gauge Black Cable

Matching 4 AWG Battery Cable

4R - 4 Gauge Red Battery Cable

Red 4 AWG battery cable for compatible marine battery and electrical wiring installations. Commonly used for positive battery cable connections.

Shop 4 Gauge Red Cable

Recommended Heat Shrink for Battery Cable Connections

After crimping a battery cable butt connector, protect the completed splice with properly sized marine-grade heat-shrink tubing.

Heat shrink helps provide electrical insulation, strain relief and protection from moisture when the tubing is appropriate for the application and correctly installed.

Item Description Color Product Link
12RB 1/2-Inch Heat Shrink - Red and Black Combination Red and Black View Heat Shrink
12R 1/2-Inch Red Heat Shrink - 1 Foot Red View Heat Shrink
12B 1/2-Inch Black Heat Shrink - 1 Foot Black View Heat Shrink

Important: Verify that the heat-shrink tubing has the appropriate expanded diameter, recovered diameter and environmental rating for the completed splice. A nominal 1/2-inch size alone does not establish fit.

How to Install a 4 Gauge Battery Cable Butt Connector

Proper installation is essential for a reliable heavy-gauge battery cable connection.

  1. Disconnect the battery. Isolate the electrical system before working on battery cables. Disconnect the negative connection first when appropriate for the installation.
  2. Measure and cut the cable. Determine the required cable length and cut the 4 AWG battery cable cleanly.
  3. Prepare the heat shrink. Slide an appropriately sized piece of heat-shrink tubing onto the cable before making the splice.
  4. Strip the cable insulation. Remove only enough insulation for the connector's required insertion depth. Avoid damaging the conductor strands.
  5. Insert the cable. Insert the stripped cable end fully into one side of the butt connector. Repeat with the second cable.
  6. Crimp the connector. Use a properly sized heavy-duty crimping tool and the crimping method specified for the connector and cable.
  7. Inspect the connection. Check that both cable ends are securely retained and the crimp is properly formed.
  8. Apply heat shrink. Center the tubing over the splice and shrink it according to the tubing manufacturer's instructions.
  9. Secure the cable. Support the completed assembly and protect it from abrasion, sharp edges and excessive movement.

Important Battery Cable Installation Information

Battery cables can carry very high current. Improperly installed connections can overheat, create excessive electrical resistance or cause electrical system failure.

  • Use only connectors approved for the cable size and conductor type.
  • Use the correct crimping tool and manufacturer-recommended crimp method.
  • Do not use ordinary pliers to crimp heavy-gauge battery cable connectors.
  • Do not rely on solder alone to secure a battery cable connection.
  • Protect the completed connection from moisture, abrasion and vibration.
  • Follow applicable marine electrical standards and equipment manufacturer requirements.
  • Use a continuous cable run where required by the engine or electrical system manufacturer.
  • Do not splice engine starting cables where the manufacturer prohibits splices.

For critical starting and high-current circuits, have the installation inspected by a qualified marine electrical technician when necessary.

Key Features and Benefits

  • 4 AWG Cable Compatibility: Designed for compatible 4 gauge battery cable connections.
  • Battery Cable Repair: Useful for joining or repairing heavy-gauge electrical cable.
  • Marine Electrical Applications: Suitable for appropriately specified boat battery and rigging installations.
  • Red or Black Cable: Can be used with compatible 4 AWG cable regardless of insulation color.
  • Crimp Connection: Designed to be installed using an appropriate heavy-duty cable crimping tool.
  • Heat-Shrink Protection: Can be protected with correctly sized external heat-shrink tubing.
  • Matching Products Available: Pro Marine USA carries 4 AWG cable and red, black and combination heat-shrink options.

Frequently Asked Questions

What size cable does the 4BC butt connector fit?

The 4BC butt connector is intended for compatible 4 gauge (4 AWG) battery cable. Confirm the connector and conductor dimensions before installation.

Can I use this connector on marine battery cables?

It can be used for appropriate marine battery cable splicing applications when the connector, cable, crimping method and environmental protection meet the installation requirements.

Can I use the same connector with red and black battery cable?

Yes. The connector is sized by cable gauge, not insulation color. It can be used with compatible 4 AWG red or black cable.

What black battery cable works with this connector?

Pro Marine USA offers 4B - 4 Gauge Black Battery Cable.

What red battery cable works with this connector?

Pro Marine USA offers 4R - 4 Gauge Red Battery Cable.

Do I need heat shrink when installing a battery cable butt connector?

For marine applications, properly selected heat-shrink tubing is recommended to insulate and protect the completed connection against moisture and corrosion.

What heat shrink can I purchase for this connector?

Pro Marine USA offers 1/2-inch heat shrink in red, black and combination packs. Confirm that the tubing will fit over the completed splice and recover tightly around the cable insulation.

Does this connector already have heat shrink attached?

This listing identifies a battery cable butt connector. Integrated heat shrink has not been confirmed. The heat-shrink products linked above are available separately.

Can I use regular pliers to crimp this connector?

No. Heavy-gauge battery cable connectors require an appropriate crimping tool and correctly matched dies or crimping method.

Can I extend an outboard engine battery cable with this connector?

Only where the engine manufacturer and applicable electrical installation requirements permit a spliced battery cable. Some engine starting circuits require continuous cable runs.

Is 4 AWG the same as 4/0 AWG?

No. 4 AWG and 4/0 AWG are different cable sizes. This connector is identified for 4 AWG cable, not 4/0 AWG cable.

Can this connector be used with 2 gauge or 6 gauge cable?

No. Use a connector specifically sized for the cable gauge being installed.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies OEM and aftermarket marine parts, electrical components, battery cables and rigging supplies to marine repair shops, dealerships, professional technicians and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on qualifying orders over $100 within the continental United States. Oil and oversized items are excluded.
  • In-stock orders placed before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options include UPS, USPS and FedEx.
  • Typical delivery is 1-5 business days, depending on destination and shipping service.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused and in original packaging.
  • Installed parts are not returnable.
  • OEM electrical components are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Selecting Battery Cable Components?

Contact Pro Marine USA for assistance identifying battery cable, electrical connectors, heat shrink and other marine rigging supplies.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

4BC, 4B, 4R, 12RB, 12R, 12B

Searchable Terms

4 gauge battery cable butt connector, 4 AWG battery cable splice, marine battery cable connector, boat battery cable butt splice, heavy gauge wire connector, 4 gauge wire splice connector, marine battery cable repair, battery cable extension connector, boat electrical rigging, marine electrical cable splice, 4 AWG red battery cable, 4 AWG black battery cable, marine battery cable heat shrink, 1/2 inch red heat shrink, 1/2 inch black heat shrink, marine battery cable fabrication, battery cable crimp connector, boat battery wiring connector, marine DC electrical connector

Item#:
4BC
Manufacturer:
Pro Marine
Available:
In Stock
23.7900
Your Price:
21.00
10 PACK
Marine-Grade 1/4" Quick Disconnect | Adhesive-Lined Terminal

Pro Marine Marine-Grade Heat Shrink Electrical Connectors

Pro Marine YFD Yellow Female Heat Shrink Disconnect – 10–12 AWG – 25 Pack

The Pro Marine YFD Yellow Female Heat Shrink Disconnect is a fully insulated, marine-grade electrical terminal designed for creating secure, removable electrical connections in boat wiring systems.

Featuring a 0.250-inch (1/4-inch) female quick-disconnect receptacle, this terminal connects to a compatible male blade terminal, allowing electrical components to be disconnected for maintenance, troubleshooting, or replacement.

Designed for 10–12 AWG electrical wire, these yellow female disconnects are suitable for marine electrical repairs, accessory installations, wiring harness repairs, and electrical equipment connections requiring larger wire sizes.

Each connector features an adhesive-lined heat-shrink insulation sleeve that helps protect the crimped wire termination from moisture, corrosion, and environmental exposure when properly installed.

The female quick-disconnect design provides a convenient, serviceable connection that can be separated and reconnected without cutting the wiring or removing the crimped terminal.

Each package contains 25 yellow female heat shrink disconnect terminals, making them ideal for marine repair shops, electrical installers, boat builders, and boat owners performing wiring repairs.

PRO MARINE BULK PURCHASE SAVINGS

BUY 4 PACKS AND SAVE 10%!

Purchase 4 packs of YFD Female Disconnects and receive a 10% discount.

4 Packs × 25 Connectors = 100 Total Connectors

SAVE 10% WHEN PURCHASING 100 CONNECTORS

Ideal for marine repair shops, boat builders, electrical installers, service technicians, and customers purchasing connectors in bulk.

Product Information

  • Part Number: YFD
  • Brand: Pro Marine
  • Product Type: Female Heat Shrink Disconnect
  • Connector Type: Female Quick Disconnect
  • Terminal Configuration: Fully Insulated
  • Wire Gauge: 10–12 AWG
  • Insulation Color: Yellow
  • Terminal Size: 0.250 Inch / 1/4 Inch
  • Terminal Material: Tinned Copper
  • Insulation Type: Adhesive-Lined Heat Shrink
  • Connection Method: Crimp and Heat Shrink
  • Shrink Ratio: Approximately 3:1
  • Package Quantity: 25 Female Disconnect Terminals
  • Bulk Purchase: 4 Packs / 100 Connectors – Save 10%
  • Application: Marine Electrical Wiring and Equipment Connections
  • Matching Male Disconnect: Pro Marine YMD (Sold Separately)
  • Condition: New

Product Identification

The following Pro Marine part numbers identify the yellow female disconnect and its separately available matching male disconnect.

Part Number Brand Description
YFD Pro Marine Yellow Female Heat Shrink Disconnect – 10–12 AWG – 25 Pack
YMD Pro Marine Matching Yellow Male Heat Shrink Disconnect – 25 Pack (Sold Separately)

What This Part Is Used For

Female heat shrink disconnect terminals provide the receptacle side of a removable electrical connection.

The terminal is crimped onto the end of an electrical wire and then connected to a compatible male quick-disconnect blade.

The 10–12 AWG wire range makes these yellow terminals suitable for installations using larger-gauge electrical wiring, provided the connector and mating connection are properly rated for the circuit.

The adhesive-lined heat-shrink sleeve helps protect the wire termination from moisture and corrosion, while the female quick-disconnect design allows connected electrical equipment to be removed or serviced without cutting the wiring.

Common Marine Electrical Applications

  • Boat electrical wiring repairs
  • Marine accessory installations
  • Electrical panel and distribution connections
  • Marine switch and control wiring
  • Boat wiring harness repairs
  • Replacement of damaged electrical terminals
  • Electrical equipment connections requiring periodic service
  • Marine lighting and accessory circuits
  • Custom boat wiring installations
  • Electrical maintenance and troubleshooting

These are general application examples. Confirm the terminal's electrical suitability before installation. Wire gauge alone does not establish the current rating of a completed connection.

Important Wire Gauge and Connector Fitment Note

Pro Marine YFD is a yellow female disconnect intended for 10–12 AWG wire and compatible 0.250-inch male disconnect terminals.

The yellow insulation identifies the 10–12 AWG wire range. This connector should not be substituted for a smaller wire-gauge terminal without verifying the appropriate crimp specifications.

This product is the female side of the connection. The corresponding male disconnect is sold separately.

Always confirm wire gauge, terminal dimensions, electrical load, and mating connector compatibility before installation.

Compatible Wire Sizes and Electrical Applications

Pro Marine YFD is designed for 10–12 AWG wire and a compatible 0.250-inch male quick-disconnect terminal.

Wire Gauge Terminal Type Connection Size Compatibility
12 AWG Female Disconnect 0.250 Inch Compatible
10 AWG Female Disconnect 0.250 Inch Compatible

Connector Configuration

Specification Description
Connection Style Female Quick Disconnect
Mating Terminal Compatible 0.250-Inch Male Disconnect
Wire Attachment Crimp Connection
Wire Insulation Protection Adhesive-Lined Heat Shrink Sleeve
Connection Function Removable and Reconnectable Electrical Connection
Marine Wiring Application Note

This terminal is not specific to a particular boat model, outboard manufacturer, or engine horsepower. Compatibility is determined by wire gauge, terminal dimensions, circuit requirements, and the mating connector. The heat-shrink sleeve protects the crimped wire termination, but the detachable male-to-female interface should not be assumed waterproof.

MATCHING MALE CONNECTION AVAILABLE

Pro Marine YMD Yellow Male Heat Shrink Disconnect – 25 Pack

Complete your electrical connection with the matching Pro Marine YMD Yellow Male Heat Shrink Disconnect.

YMD provides the male blade side of the connection and is designed to mate with a compatible 0.250-inch female terminal.

Pairing the male and female disconnects allows electrical components to be connected, disconnected, and serviced without cutting the wiring.

Female Connection: YFD – Yellow Female Disconnect

Male Connection: YMD – Yellow Male Disconnect

Both products are sold in 25-piece packages. Male and female terminals are purchased separately.

View YMD Male Disconnect – 25 Pack

Common Symptoms and Replacement Reasons

Marine electrical terminals may need replacement when corrosion, physical damage, or poor contact affects the reliability of the connection.

Common Reasons to Replace a Female Disconnect

  • Corrosion or oxidation on the female terminal
  • Loose or worn female receptacle
  • Damaged heat-shrink insulation
  • Broken or deteriorated wire termination
  • Intermittent electrical accessory operation
  • Signs of overheating or discoloration
  • Damaged wiring harness connections
  • Installation of new marine electrical equipment
  • Replacement of unsuitable or incorrectly sized terminals
  • Preventive electrical wiring maintenance

Inspect both sides of the electrical connection. A damaged or undersized mating male terminal can also contribute to unreliable contact.

Installation and Service Tips

Proper crimping and heat-shrink installation help produce a dependable wire termination in marine electrical environments.

Recommended Installation Practices

  • Disconnect electrical power before beginning wiring repairs.
  • Confirm that the wire size is 10 AWG or 12 AWG.
  • Verify that the mating male terminal uses a compatible 0.250-inch blade.
  • Strip the wire insulation to the appropriate length for the crimp barrel.
  • Insert the prepared wire fully into the terminal barrel.
  • Use a crimping tool designed for insulated heat-shrink terminals and the correct wire-gauge range.
  • Crimp the terminal securely and inspect the completed connection.
  • Use a controlled heat gun to recover the heat-shrink sleeve.
  • Apply heat evenly until the insulation conforms around the wire and forms its seal.
  • Allow the connection to cool before handling or applying mechanical stress.
  • Inspect the terminal for exposed wire, incomplete shrinkage, or damaged insulation.
  • Verify secure engagement with the male terminal before restoring electrical power.
Important Installation Warning

Incorrect wire sizing, improper crimping, excessive heat, or loose terminal engagement can cause electrical resistance, overheating, or connection failure. Follow applicable marine electrical installation standards and do not use an open flame to shrink the insulation.

Key Features and Benefits

  • Marine-Grade Electrical Terminal: Suitable for marine wiring applications where moisture and corrosion protection are important.
  • Female Quick-Disconnect Design: Provides the receptacle side of a removable electrical connection.
  • Adhesive-Lined Heat Shrink: Helps seal the crimped wire termination against moisture and environmental exposure.
  • Tinned Copper Construction: Provides electrical conductivity with corrosion-resistant terminal plating.
  • 10–12 AWG Wire Compatibility: Designed for the specified larger-gauge electrical wiring range.
  • Standard 0.250-Inch Connection: Connects to compatible 1/4-inch male quick-disconnect terminals.
  • Serviceable Electrical Connection: Allows connected equipment to be disconnected without cutting the wiring.
  • Yellow Insulation: Provides convenient identification of the intended wire-gauge range.
  • Convenient 25-Pack: Provides multiple terminals for marine wiring repairs and installations.
  • Bulk Purchase Savings: Buy four 25-packs for 100 total connectors and save 10%.
  • Matching Male Version Available: Pro Marine YMD male disconnects are sold separately.
  • Dealer Pricing: Qualified marine professionals can apply for wholesale pricing.

Frequently Asked Questions

What is Pro Marine YFD?

Pro Marine YFD is a yellow female heat shrink quick-disconnect terminal sold in a 25-piece package. It provides the female receptacle side of a removable electrical connection.

What wire gauge does YFD fit?

YFD is intended for 10–12 AWG wire. Always verify the wire gauge before installation.

What size male terminal fits YFD?

YFD accepts a compatible 0.250-inch (1/4-inch) male blade. The male terminal must have the correct dimensions and electrical rating.

Does Pro Marine sell the matching male disconnect?

Yes. Pro Marine offers the YMD Yellow Male Heat Shrink Disconnect in a 25-piece package.

View Pro Marine YMD Male Disconnect

Are these female disconnects waterproof?

The adhesive-lined heat-shrink sleeve helps create a moisture-resistant seal around the crimped wire termination. The removable male-to-female interface itself should not be considered waterproof unless the complete assembly is rated for that application.

Can YFD connectors be disconnected and reconnected?

Yes. Quick-disconnect terminals are designed to allow electrical equipment to be separated and reconnected for servicing. Replace terminals if they become loose, corroded, or damaged.

How many connectors are included in one pack?

Each Pro Marine YFD package contains 25 yellow female heat shrink disconnect terminals. Male terminals are sold separately.

Is there a discount when purchasing 100 connectors?

Yes. Purchase 4 packs of YFD for a total of 100 female disconnect terminals and save 10%.

Can these terminals be used for boat electrical repairs?

Yes. They can be used in suitable marine electrical wiring applications when the wire gauge, connector size, electrical load, and installation environment are appropriate.

Are yellow disconnects interchangeable with red disconnects?

Not for crimping onto the same wire size. Yellow disconnects are designed for 10–12 AWG wire, while red disconnects in this product range are intended for smaller wire gauges. Select the terminal according to the actual wire size.

What tools are needed to install YFD terminals?

Use a suitable wire stripper, a crimping tool and die appropriate for 10–12 AWG insulated heat-shrink terminals, and a controlled heat gun to recover the insulation sleeve.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies genuine OEM and aftermarket marine engine parts, electrical connectors, wiring components, and maintenance products to professional marine technicians, repair shops, dealerships, and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible marine parts and supplies.

Dealer accounts provide professional marine businesses with access to competitive wholesale pricing and convenient online ordering.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on orders over $100 within the continental United States.
  • In-stock orders received before 5:30 PM EST ship the same business day, Monday–Friday.
  • Shipping options available through UPS, USPS, and FedEx.
  • Typical delivery time is 1–5 business days.
  • Shipping times may vary based on destination, carrier service, and product availability.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Products must be new, unused, and in original packaging.
  • Installed or crimped electrical terminals are not returnable.
  • Return authorization is required before returning merchandise.
  • Contact Pro Marine USA before returning any merchandise.

Need Help Selecting Electrical Connectors?

Need assistance confirming the correct wire gauge, connector type, or marine electrical component?

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

YFD, YMD

YMD is the separately available matching male disconnect. Male terminals are not included with YFD.

Searchable Terms

Pro Marine YFD, YFD female disconnect, yellow female heat shrink disconnect, yellow female quick disconnect, marine female disconnect terminal, marine electrical quick disconnect, yellow female spade connector, yellow female blade connector, 1/4 inch female disconnect, 0.250 inch female disconnect, 250 series female terminal, 10 AWG female disconnect, 12 AWG female disconnect, 10-12 AWG heat shrink terminal, 12-10 AWG female disconnect, yellow insulated female terminal, fully insulated female disconnect, adhesive lined heat shrink terminal, tinned copper disconnect terminal, marine grade electrical connector, marine wiring connector, boat electrical connector, boat wiring repair terminal, marine accessory wiring connector, marine switch wiring terminal, marine electrical repair supplies, removable electrical connector, crimp heat shrink disconnect, heat shrink spade terminal, heat shrink blade terminal, female quick connect terminal, marine quick connect terminal, yellow female disconnect 25 pack, female electrical connectors bulk, 100 female disconnect terminals, bulk marine electrical connectors, Pro Marine heat shrink terminals, marine electrical terminal supplies

Item#:
YFD
Manufacturer:
Pacer Wire & Connectors
Available:
In Stock
18.0000
Your Price:
16.00
Each
Marine-Grade 1/4" Male Quick Disconnect | Adhesive-Lined Terminal

Pro Marine Marine-Grade Heat Shrink Electrical Connectors

Pro Marine YMD Yellow Male Heat Shrink Disconnect – 10–12 AWG – 25 Pack

The Pro Marine YMD Yellow Male Heat Shrink Disconnect is a marine-grade electrical terminal designed to create secure, removable connections in boat wiring systems. Featuring a 0.250-inch (1/4-inch) male blade terminal, this connector mates with a compatible female quick-disconnect terminal.

Designed for 10–12 AWG electrical wire, these yellow male disconnects are suitable for marine electrical repairs, accessory installations, wiring harness repairs, and equipment connections requiring larger wire sizes.

Each connector features an adhesive-lined heat-shrink insulation sleeve that helps protect the crimped wire termination from moisture, corrosion, and environmental exposure when properly installed.

The male quick-disconnect design provides a convenient connection point for electrical components that may need to be disconnected for maintenance, troubleshooting, inspection, or replacement.

For a complete removable connection, pair this male terminal with the matching Pro Marine YFD Yellow Female Heat Shrink Disconnect, sold separately.

Each package contains 25 yellow male heat shrink disconnect terminals, making them ideal for marine repair shops, boat builders, electrical installers, and boat owners performing wiring repairs.

PRO MARINE BULK PURCHASE SAVINGS

BUY 4 PACKS AND SAVE 10%!

Purchase 4 packs of YMD Male Disconnects and receive a 10% discount.

4 Packs × 25 Connectors = 100 Total Connectors

SAVE 10% WHEN PURCHASING 100 CONNECTORS

Ideal for marine repair shops, boat builders, electrical installers, service technicians, and customers purchasing connectors in bulk.

Product Information

  • Part Number: YMD
  • Brand: Pro Marine
  • Product Type: Male Heat Shrink Disconnect
  • Connector Type: Male Quick Disconnect
  • Terminal Configuration: Insulated Crimp Barrel with Male Blade
  • Wire Gauge: 10–12 AWG
  • Insulation Color: Yellow
  • Terminal Size: 0.250 Inch / 1/4 Inch
  • Insulation Type: Adhesive-Lined Heat Shrink
  • Connection Method: Crimp and Heat Shrink
  • Package Quantity: 25 Male Disconnect Terminals
  • Bulk Purchase: 4 Packs / 100 Connectors – Save 10%
  • Application: Marine Electrical Wiring and Equipment Connections
  • Matching Female Disconnect: Pro Marine YFD (Sold Separately)
  • Condition: New

Product Identification

The following Pro Marine part numbers identify the yellow male disconnect and its separately available matching female disconnect.

Part Number Brand Description
YMD Pro Marine Yellow Male Heat Shrink Disconnect – 10–12 AWG – 25 Pack
YFD Pro Marine Matching Yellow Female Heat Shrink Disconnect – 25 Pack (Sold Separately)

What This Part Is Used For

Male heat shrink disconnect terminals provide the blade side of a removable electrical connection. The terminal is crimped onto the end of a wire and then connected to a compatible female quick-disconnect receptacle.

The 10–12 AWG wire range makes these yellow terminals suitable for electrical installations using larger-gauge wiring, provided the terminal and mating connection are appropriately rated for the circuit.

The heat-shrink insulation helps protect the crimped wire termination from moisture and corrosion, while the male quick-disconnect design allows connected equipment to be removed or serviced without cutting the wiring.

Common Marine Electrical Applications

  • Boat electrical wiring repairs
  • Marine accessory installations
  • Electrical panel and distribution connections
  • Marine switch and control wiring
  • Boat wiring harness repairs
  • Replacement of damaged electrical terminals
  • Electrical equipment connections requiring periodic service
  • Marine lighting and accessory circuits
  • Custom boat wiring installations
  • Electrical maintenance and troubleshooting

These are general application examples. Confirm the terminal's electrical suitability before installation. Wire gauge alone does not establish the current rating of a completed connection.

Important Wire Gauge and Connector Fitment Note

Pro Marine YMD is a yellow male disconnect intended for 10–12 AWG wire and compatible 0.250-inch female disconnect terminals.

The yellow insulation identifies the 10–12 AWG wire range. This connector should not be substituted for a smaller wire-gauge terminal without verifying the appropriate crimp specifications.

This product is the male side of the connection. The corresponding female disconnect is sold separately.

Always confirm wire gauge, terminal dimensions, electrical load, and mating connector compatibility before installation.

Compatible Wire Sizes and Electrical Applications

Pro Marine YMD is designed for 10–12 AWG wire and a compatible 0.250-inch female quick-disconnect terminal.

Wire Gauge Terminal Type Connection Size Compatibility
12 AWG Male Disconnect 0.250 Inch Compatible
10 AWG Male Disconnect 0.250 Inch Compatible

Connector Configuration

Specification Description
Connection Style Male Quick Disconnect
Mating Terminal Compatible 0.250-Inch Female Disconnect
Wire Attachment Crimp Connection
Wire Insulation Protection Adhesive-Lined Heat Shrink Sleeve
Connection Function Removable and Reconnectable Electrical Connection
Marine Wiring Application Note

This terminal is not specific to a particular boat model, outboard manufacturer, or engine horsepower. Compatibility is determined by wire gauge, terminal dimensions, circuit requirements, and the mating connector. The heat-shrink sleeve protects the crimped wire termination, but the detachable male-to-female interface should not be assumed waterproof.

MATCHING FEMALE CONNECTION AVAILABLE

Pro Marine YFD Yellow Female Heat Shrink Disconnect – 25 Pack

Complete your electrical connection with the matching Pro Marine YFD Yellow Female Heat Shrink Disconnect.

YFD provides the female receptacle side of the connection and is designed to mate with a compatible 0.250-inch male blade terminal.

Pairing the male and female disconnects allows electrical components to be connected, disconnected, and serviced without cutting the wiring.

Male Connection: YMD – Yellow Male Disconnect

Female Connection: YFD – Yellow Female Disconnect

Both products are sold in 25-piece packages. Male and female terminals are purchased separately.

View YFD Female Disconnect – 25 Pack

Common Symptoms and Replacement Reasons

Marine electrical terminals may need replacement when corrosion, physical damage, or poor contact affects the reliability of the connection.

Common Reasons to Replace a Male Disconnect

  • Corrosion or oxidation on the male blade terminal
  • Bent, broken, or damaged male blades
  • Loose or worn quick-disconnect connections
  • Damaged heat-shrink insulation
  • Broken or deteriorated wire termination
  • Intermittent electrical accessory operation
  • Signs of overheating or discoloration
  • Damaged wiring harness connections
  • Installation of new marine electrical equipment
  • Preventive electrical wiring maintenance

Inspect both sides of the electrical connection. A damaged or loose female receptacle can also contribute to unreliable contact with the male blade.

Installation and Service Tips

Proper crimping and heat-shrink installation help produce a dependable wire termination in marine electrical environments.

Recommended Installation Practices

  • Disconnect electrical power before beginning wiring repairs.
  • Confirm that the wire size is 10 AWG or 12 AWG.
  • Verify that the mating female terminal accepts a compatible 0.250-inch male blade.
  • Strip the wire insulation to the appropriate length for the crimp barrel.
  • Insert the prepared wire fully into the terminal barrel.
  • Use a crimping tool designed for insulated heat-shrink terminals and the correct wire-gauge range.
  • Crimp the terminal securely and inspect the completed connection.
  • Use a controlled heat gun to recover the heat-shrink sleeve.
  • Apply heat evenly until the insulation conforms around the wire and forms its seal.
  • Allow the connection to cool before handling or applying mechanical stress.
  • Inspect the male blade for damage or distortion before connecting.
  • Verify secure engagement with the female terminal before restoring electrical power.
Important Installation Warning

Incorrect wire sizing, improper crimping, excessive heat, or loose terminal engagement can cause electrical resistance, overheating, or connection failure. Follow applicable marine electrical installation standards and do not use an open flame to shrink the insulation.

Key Features and Benefits

  • Marine-Grade Electrical Terminal: Suitable for marine wiring applications where moisture and corrosion protection are important.
  • Male Quick-Disconnect Design: Provides the blade side of a removable electrical connection.
  • Adhesive-Lined Heat Shrink: Helps seal the crimped wire termination against moisture and environmental exposure.
  • 10–12 AWG Wire Compatibility: Designed for the specified larger-gauge electrical wiring range.
  • Standard 0.250-Inch Connection: Connects to compatible 1/4-inch female quick-disconnect terminals.
  • Serviceable Electrical Connection: Allows connected equipment to be disconnected without cutting the wiring.
  • Yellow Insulation: Provides convenient identification of the intended wire-gauge range.
  • Convenient 25-Pack: Provides multiple terminals for marine wiring repairs and installations.
  • Bulk Purchase Savings: Buy four 25-packs for 100 total connectors and save 10%.
  • Matching Female Version Available: Pro Marine YFD female disconnects are sold separately.
  • Dealer Pricing: Qualified marine professionals can apply for wholesale pricing.

Frequently Asked Questions

What is Pro Marine YMD?

Pro Marine YMD is a yellow male heat shrink quick-disconnect terminal sold in a 25-piece package. It provides the male blade side of a removable electrical connection.

What wire gauge does YMD fit?

YMD is intended for 10–12 AWG wire. Always verify wire gauge before installation.

What size female disconnect fits YMD?

YMD features a 0.250-inch (1/4-inch) male blade. It connects to a compatible female disconnect of the same size.

Does Pro Marine sell the matching female disconnect?

Yes. Pro Marine offers the YFD Yellow Female Heat Shrink Disconnect in a 25-piece package.

View Pro Marine YFD Female Disconnect

Are these male disconnects waterproof?

The adhesive-lined heat-shrink sleeve helps create a moisture-resistant seal around the crimped wire termination. The removable male-to-female interface itself should not be considered waterproof unless the complete assembly is rated for that application.

Can the male and female terminals be disconnected and reconnected?

Yes. Quick-disconnect terminals allow electrical equipment to be disconnected and reconnected for maintenance or replacement. Replace terminals if they become loose, damaged, or corroded.

How many connectors are included in one pack?

Each Pro Marine YMD package contains 25 yellow male heat shrink disconnect terminals. Female terminals are sold separately.

Is there a discount when purchasing 100 connectors?

Yes. Purchase 4 packs of YMD for a total of 100 male disconnect terminals and save 10%.

Can these terminals be used for boat electrical repairs?

Yes. They can be used in suitable marine electrical wiring applications when the wire gauge, connector size, electrical load, and installation environment are appropriate.

Are yellow disconnects interchangeable with red disconnects?

Not for crimping onto the same wire size. Yellow disconnects are designed for 10–12 AWG wire, while red disconnects in this product range are intended for smaller wire gauges. Select the terminal according to the actual wire size.

What tools are needed to install YMD terminals?

Use a suitable wire stripper, a crimping tool and die appropriate for 10–12 AWG insulated heat-shrink terminals, and a controlled heat gun to recover the insulation sleeve.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies genuine OEM and aftermarket marine engine parts, electrical connectors, wiring components, and maintenance products to professional marine technicians, repair shops, dealerships, and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible marine parts and supplies.

Dealer accounts provide professional marine businesses with access to competitive wholesale pricing and convenient online ordering.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on orders over $100 within the continental United States.
  • In-stock orders received before 5:30 PM EST ship the same business day, Monday–Friday.
  • Shipping options available through UPS, USPS, and FedEx.
  • Typical delivery time is 1–5 business days.
  • Shipping times may vary based on destination, carrier service, and product availability.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Products must be new, unused, and in original packaging.
  • Installed or crimped electrical terminals are not returnable.
  • Return authorization is required before returning merchandise.
  • Contact Pro Marine USA before returning any merchandise.

Need Help Selecting Electrical Connectors?

Need assistance confirming the correct wire gauge, connector type, or marine electrical component?

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

YMD, YFD

YFD is the separately available matching female disconnect. Female terminals are not included with YMD.

Searchable Terms

Pro Marine YMD, YMD male disconnect, yellow male heat shrink disconnect, yellow male quick disconnect, marine male disconnect terminal, marine electrical quick disconnect, yellow male spade connector, yellow male blade connector, 1/4 inch male disconnect, 0.250 inch male disconnect, 250 series male terminal, 10 AWG male disconnect, 12 AWG male disconnect, 10-12 AWG heat shrink terminal, 12-10 AWG male disconnect, yellow insulated male terminal, adhesive lined heat shrink terminal, marine grade electrical connector, marine wiring connector, boat electrical connector, boat wiring repair terminal, marine accessory wiring connector, marine switch wiring terminal, marine electrical repair supplies, removable electrical connector, crimp heat shrink disconnect, heat shrink spade terminal, heat shrink blade terminal, male quick connect terminal, marine quick connect terminal, yellow male disconnect 25 pack, male electrical connectors bulk, 100 male disconnect terminals, bulk marine electrical connectors, Pro Marine heat shrink terminals, marine electrical terminal supplies

Item#:
YMD
Manufacturer:
Pacer Wire & Connectors
Available:
In Stock
19.0000
Your Price:
18.25
Each
Heat Shrinkable10-12 Gauge
Item#:
YPB
Manufacturer:
Pacer Wire & Connectors
Available:
In Stock
Your Price:
19.89
25 PACK
Item#:
316R
Manufacturer Item:
BEHS-3/16R
Manufacturer:
Pacer Wire & Connectors
Available:
In Stock
Your Price:
3.04
Each
Heavy Gauge Battery Cable Splice Connector for Boats and Marine Rigging

Marine Battery Cable and Electrical Rigging

6 Gauge Battery Cable Butt Connector - 6 AWG Marine Cable Splice

The 6BC Battery Cable Butt Connector is designed for joining two sections of 6 gauge (6 AWG) battery cable. This heavy-gauge electrical connector is used for battery cable repairs, cable extensions and custom marine electrical installations.

Whether repairing an existing battery cable or building a custom cable assembly, a properly installed butt connector provides a mechanical and electrical connection between two cable ends.

The 6BC connector can be used with compatible 6 AWG red or black battery cable. For marine applications, the completed connection should be protected with appropriately sized marine-grade heat-shrink tubing to help prevent moisture intrusion and corrosion.

Pro Marine USA also carries matching 6 gauge battery cable and 1/2-inch heat shrink in red, black and combination packs, making it easy to purchase the materials needed for your battery cable installation.

Product Information

  • Item Number: 6BC
  • Product: Battery Cable Butt Connector
  • Cable Size: 6 Gauge / 6 AWG
  • Connector Type: Butt Splice Connector
  • Application: Battery Cable Splicing and Repair
  • Compatible Cable: 6 AWG Battery Cable
  • Connection Type: Crimped Cable Splice
  • Installation: Requires an appropriate heavy-duty cable crimping tool
  • Recommended Protection: Compatible Marine-Grade Heat Shrink
  • Typical Uses: Marine Battery Cables, Electrical Rigging and Cable Repairs

OEM and Cross Reference Numbers

The 6BC is a general-purpose battery cable connector rather than an engine-specific OEM replacement part. No additional manufacturer cross-reference numbers have been provided for this connector.

Item Number Description Application
6BC 6 Gauge Battery Cable Butt Connector 6 AWG Cable Splicing

What This Part Is Used For

The 6BC butt connector is used to join two sections of 6 AWG battery cable when repairing, extending or assembling heavy-gauge electrical wiring.

Marine battery cables can carry significant electrical current. Connections must be properly sized, securely crimped and protected against moisture and corrosion.

Common Applications

  • Marine battery cable repairs
  • Joining two sections of 6 AWG battery cable
  • Custom battery cable fabrication
  • Boat electrical system rigging
  • Battery cable extensions where permitted by the installation requirements
  • Battery switch and distribution wiring repairs
  • Marine engine battery cable service
  • Other compatible heavy-gauge DC electrical installations

This connector is not engine-specific. Compatibility is determined primarily by the cable gauge, conductor construction and electrical installation requirements.

Compatible Battery Cable Applications

The 6BC connector is intended for use with compatible 6 gauge battery cable. Pro Marine USA offers the following matching cable options.

Item Description Cable Size Color Product
6B Battery Cable - Black 6 AWG Black View Cable
6R Battery Cable - Red 6 AWG Red View Cable

Build or Repair Your 6 Gauge Battery Cable

Complete your battery cable installation with compatible 6 AWG cable and heat-shrink tubing available from Pro Marine USA.

Matching 6 AWG Battery Cable

6B - 6 Gauge Black Battery Cable

Black 6 AWG battery cable for compatible marine battery and electrical wiring installations. Commonly used for negative battery cable connections.

Shop 6 Gauge Black Cable

Matching 6 AWG Battery Cable

6R - 6 Gauge Red Battery Cable

Red 6 AWG battery cable for compatible marine battery and electrical wiring installations. Commonly used for positive battery cable connections.

Shop 6 Gauge Red Cable

Recommended Heat Shrink for Battery Cable Connections

After crimping a battery cable butt connector, protect the completed splice with properly sized marine-grade heat-shrink tubing.

Heat shrink helps provide electrical insulation, strain relief and protection from moisture when the tubing is appropriate for the application and correctly installed.

Item Description Color Product Link
12RB 1/2-Inch Heat Shrink - Red and Black Combination Red and Black View Heat Shrink
12R 1/2-Inch Red Heat Shrink - 1 Foot Red View Heat Shrink
12B 1/2-Inch Black Heat Shrink - 1 Foot Black View Heat Shrink

Important: Verify that the heat-shrink tubing has the appropriate expanded diameter, recovered diameter and environmental rating for the completed splice. A nominal 1/2-inch size alone does not establish fit.

How to Install a 6 Gauge Battery Cable Butt Connector

Proper installation is essential for a reliable heavy-gauge battery cable connection.

  1. Disconnect the battery. Isolate the electrical system before working on battery cables. Disconnect the negative connection first when appropriate for the installation.
  2. Measure and cut the cable. Determine the required cable length and cut the 6 AWG battery cable cleanly.
  3. Prepare the heat shrink. Slide an appropriately sized piece of heat-shrink tubing onto the cable before making the splice.
  4. Strip the cable insulation. Remove only enough insulation for the connector's required insertion depth. Avoid damaging the conductor strands.
  5. Insert the cable. Insert the stripped cable end fully into one side of the butt connector. Repeat with the second cable.
  6. Crimp the connector. Use a properly sized heavy-duty crimping tool and the crimping method specified for the connector and cable.
  7. Inspect the connection. Check that both cable ends are securely retained and the crimp is properly formed.
  8. Apply heat shrink. Center the tubing over the splice and shrink it according to the tubing manufacturer's instructions.
  9. Secure the cable. Support the completed assembly and protect it from abrasion, sharp edges and excessive movement.

Important Battery Cable Installation Information

Battery cables can carry very high current. Improperly installed connections can overheat, create excessive electrical resistance or cause electrical system failure.

  • Use only connectors approved for the cable size and conductor type.
  • Use the correct crimping tool and manufacturer-recommended crimp method.
  • Do not use ordinary pliers to crimp heavy-gauge battery cable connectors.
  • Do not rely on solder alone to secure a battery cable connection.
  • Protect the completed connection from moisture, abrasion and vibration.
  • Follow applicable marine electrical standards and equipment manufacturer requirements.
  • Use a continuous cable run where required by the engine or electrical system manufacturer.
  • Do not splice engine starting cables where the manufacturer prohibits splices.

For critical starting and high-current circuits, have the installation inspected by a qualified marine electrical technician when necessary.

Key Features and Benefits

  • 6 AWG Cable Compatibility: Designed for compatible 6 gauge battery cable connections.
  • Battery Cable Repair: Useful for joining or repairing heavy-gauge electrical cable.
  • Marine Electrical Applications: Suitable for appropriately specified boat battery and rigging installations.
  • Red or Black Cable: Can be used with compatible 6 AWG cable regardless of insulation color.
  • Crimp Connection: Designed to be installed using an appropriate heavy-duty cable crimping tool.
  • Heat-Shrink Protection: Can be protected with correctly sized external heat-shrink tubing.
  • Matching Products Available: Pro Marine USA carries 6 AWG cable and red, black and combination heat-shrink options.

Frequently Asked Questions

What size cable does the 6BC butt connector fit?

The 6BC butt connector is intended for compatible 6 gauge (6 AWG) battery cable. Confirm the connector and conductor dimensions before installation.

Can I use this connector on marine battery cables?

It can be used for appropriate marine battery cable splicing applications when the connector, cable, crimping method and environmental protection meet the installation requirements.

Can I use the same connector with red and black battery cable?

Yes. The connector is sized by cable gauge, not insulation color. It can be used with compatible 6 AWG red or black cable.

What black battery cable works with this connector?

Pro Marine USA offers 6B - 6 Gauge Black Battery Cable.

What red battery cable works with this connector?

Pro Marine USA offers 6R - 6 Gauge Red Battery Cable.

Do I need heat shrink when installing a battery cable butt connector?

For marine applications, properly selected heat-shrink tubing is recommended to insulate and protect the completed connection against moisture and corrosion.

What heat shrink can I purchase for this connector?

Pro Marine USA offers 1/2-inch heat shrink in red, black and combination packs. Confirm that the tubing will fit over the completed splice and recover tightly around the cable insulation.

Does this connector already have heat shrink attached?

This listing identifies a battery cable butt connector. Integrated heat shrink has not been confirmed. The heat-shrink products linked above are available separately.

Can I use regular pliers to crimp this connector?

No. Heavy-gauge battery cable connectors require an appropriate crimping tool and correctly matched dies or crimping method.

Can I extend an outboard engine battery cable with this connector?

Only where the engine manufacturer and applicable electrical installation requirements permit a spliced battery cable. Some engine starting circuits require continuous cable runs.

Is 6 AWG the same as 6/0 AWG?

No. 6 AWG and 6/0 AWG are different cable sizes. This connector is identified for 6 AWG cable, not larger cable sizes.

Can this connector be used with 4 gauge or 8 gauge cable?

No. Use a connector specifically sized for the cable gauge being installed.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies OEM and aftermarket marine parts, electrical components, battery cables and rigging supplies to marine repair shops, dealerships, professional technicians and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on qualifying orders over $100 within the continental United States. Oil and oversized items are excluded.
  • In-stock orders placed before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options include UPS, USPS and FedEx.
  • Typical delivery is 1-5 business days, depending on destination and shipping service.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused and in original packaging.
  • Installed parts are not returnable.
  • OEM electrical components are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Selecting Battery Cable Components?

Contact Pro Marine USA for assistance identifying battery cable, electrical connectors, heat shrink and other marine rigging supplies.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

6BC, 6B, 6R, 12RB, 12R, 12B

Searchable Terms

6 gauge battery cable butt connector, 6 AWG battery cable splice, marine battery cable connector, boat battery cable butt splice, heavy gauge wire connector, 6 gauge wire splice connector, marine battery cable repair, battery cable extension connector, boat electrical rigging, marine electrical cable splice, 6 AWG red battery cable, 6 AWG black battery cable, marine battery cable heat shrink, 1/2 inch red heat shrink, 1/2 inch black heat shrink, marine battery cable fabrication, battery cable crimp connector, boat battery wiring connector, marine DC electrical connector

Item#:
6BC
Manufacturer:
Pro Marine
Available:
In Stock
11.8800
Your Price:
10.75
10 PACK
Item#:
3-334
Manufacturer Item:
035340
Manufacturer:
Moeller
Available:
In Stock
 
Oversized Shipping
Your Price:
150.99
Each
Item#:
3-333
Cross Reference#:
39729333304
Manufacturer Item:
035330
Manufacturer:
Moeller
Available:
In Stock
 
Oversized Shipping
Your Price:
134.19
Each
Item#:
YB-06548
Manufacturer Item:
YB-06548
Manufacturer:
Yamaha Outboard
Available:
In Stock
Your Price:
237.51
Each
Item#:
9-082
Cross Reference#:
39729082004
Manufacturer:
Moeller
Available:
In Stock
Your Price:
38.59
Each
|◀ ◀ 805 - 816 of 1065 ▶ ▶|
View: