Yamaha 703 10-Pin Side Mount Remote Control 15ft Harness - 4820

Compatible Applications

Pro Marine 48207SP is designed for compatible Yamaha outboards using the 10-pin Yamaha mechanical-control system.

Pro Marine's application information identifies the following Yamaha engine families for this control:

OEM and Cross Reference Numbers

Pro Marine 48207SP replaces a large number of Yamaha 703 side-mount remote-control assemblies. These older and superseded numbers are important when identifying a replacement control from an existing Yamaha rigging system.

What This Control is Used For

The Yamaha 703 side-mount control is the operator's primary interface with a compatible mechanically controlled Yamaha outboard.

Moving the control lever operates the engine's mechanical throttle and shift cables, allowing the operator to select forward, neutral and reverse while controlling engine speed from the helm.

The control also integrates the electrical functions needed for the compatible Yamaha 10-pin rigging system.

15-Foot 10-Pin Harness

Pro Marine 48207SP is supplied with a 15-foot electrical harness for compatible Yamaha 10-pin applications.

The harness provides the electrical connection between the remote control and the compatible engine rigging system.

Push-to-Choke Ignition

The 48207SP control is configured with the push-to-choke ignition function used on compatible Yamaha mechanical-control outboards.

This allows the applicable engine starting / enrichment function to be operated through the ignition switch rather than requiring a separate helm-mounted choke control.

Power Trim and Tilt Control

The Yamaha 703-style control incorporates power trim and tilt control for compatible Yamaha outboards.

This allows the operator to adjust engine trim while maintaining control of the throttle and shift lever.

Mechanical Throttle and Shift

Pro Marine 48207SP is for mechanically controlled Yamaha outboards.

A mechanical-control system uses physical throttle and shift cables between the remote-control box and the engine.

This control should not be confused with Yamaha electronic throttle-and-shift or drive-by-wire control systems.

Yamaha 703 Side Mount Design

The Yamaha 703 control family uses a side-mount remote-control configuration. This style is commonly installed on the side of the helm, console or cockpit where the operator can comfortably reach the control lever.

If replacing an existing Yamaha 703 control, compare the original mounting arrangement, electrical connector and OEM control number before installation.

Replacing an Older Yamaha 703 Control

Yamaha used numerous part numbers for variations and revisions of the 703 remote-control family. This is why an older control may carry a number beginning with 703-48201, 703-48205 or 703-48207.

Pro Marine 48207SP provides a replacement option for the compatible mechanical 10-pin applications represented by the cross-reference numbers listed above.

Common Reasons to Replace a Yamaha Remote Control

• Excessive play in the control lever
• Stiff or inconsistent throttle movement
• Difficult shifting
• Worn internal control mechanism
• Failed ignition switch
• Failed trim and tilt switch
• Damaged or corroded electrical harness
• Damaged control housing
• Corrosion inside an older control box
• Complete boat rerigging or restoration

Installation Tips

• Verify that the engine uses mechanical throttle and shift controls.
• Confirm that the electrical system uses the compatible Yamaha 10-pin connection.
• Compare the original control part number with the cross-reference list.
• Confirm that the 15-foot harness length is suitable for the installation.
• Inspect the throttle and shift cables while the old control is removed.
• Replace stiff, damaged or corroded control cables before installation.
• Route the harness and cables without sharp bends or excessive tension.
• Adjust throttle and shift cables according to Yamaha service procedures.
• Verify forward, neutral and reverse operation before operating the boat.
• Test ignition, push-to-choke and power trim functions after installation.

Key Features and Benefits

• Pro Marine aftermarket Yamaha remote control
• Yamaha 703-style side-mount design
• Designed for compatible mechanical-control Yamaha outboards
• Mechanical throttle and shift operation
• 10-pin electrical connection
• 15-foot harness
• Push-to-choke ignition function
• Integrated power trim and tilt control
• Replaces numerous Yamaha 703 remote-control numbers
• Manufacturer reference 703-48207-21-00
• Pro Marine item number 48207SP

FAQ

What is Pro Marine 48207SP?
It is a Pro Marine aftermarket Yamaha 703-style side-mount mechanical remote control with a 10-pin electrical connection and 15-foot harness.

Is 48207SP a complete remote control or just a wiring harness?
It is a remote-control assembly with the 15-foot harness, not simply a replacement wiring harness.

Is this a mechanical Yamaha control?
Yes. This control is intended for compatible Yamaha outboards using mechanical throttle and shift cables.

What type of electrical connection does it use?
Pro Marine 48207SP uses the compatible Yamaha 10-pin electrical connection.

How long is the harness?
The control is supplied with a 15-foot harness.

Does it have power trim and tilt control?
Yes. The compatible Yamaha 703 control configuration includes power trim and tilt control.

Does this control have push-to-choke?
Yes. Pro Marine lists 48207SP with a push-to-choke ignition configuration.

Does 48207SP replace Yamaha 703-48207-21-00?
Yes. Pro Marine identifies 703-48207-21-00 as the manufacturer reference for 48207SP.

Does it replace Yamaha 703-48207-25-00?
Yes. 703-48207-25-00 is included in the supplied and verified cross-reference list for this control family.

Does it replace older 703-48205 controls?
Yes. Numerous 703-48205 numbers are included in the cross-reference list, including A-series and 10-series control numbers.

Will this work with Yamaha electronic controls?
No. This listing is for compatible mechanical throttle and shift applications, not Yamaha electronic throttle-and-shift systems.

Will it fit every Yamaha outboard in the listed horsepower range?
No. Horsepower alone does not determine control compatibility. Verify that your engine uses the compatible mechanical-control system and 10-pin electrical connection, or match the original control to one of the listed OEM numbers.

Searchable Part Numbers

48207SP, 703-48201-A0-00, 703-48201-A1-00, 703-48201-A2-00, 703-48201-A3-00, 703-48205-A0-00, 703-48205-A1-00, 703-48205-A2-00, 703-48205-A3-00, 703-48205-A4-00, 703-48205-A5-00, 703-48205-10-00, 703-48205-11-00, 703-48205-12-00, 703-48205-13-00, 703-48205-15-00, 703-48205-16-00, 703-48205-17-00, 703-48207-A1-00, 703-48207-A3-00, 703-48207-A4-00, 703-48207-1A-00, 703-48207-1A-10, 703-48207-1B-10, 703-48207-10-00, 703-48207-11-00, 703-48207-12-00, 703-48207-13-00, 703-48207-14-00, 703-48207-15-00, 703-48207-15-10, 703-48207-16-10, 703-48207-17-10, 703-48207-18-10, 703-48207-20-00, 703-48207-21-00, 703-48207-22-00, 703-48207-23-00, 703-48207-24-00, 703-48207-25-00

Searchable Terms

Yamaha 703 remote control, Yamaha 703 control box, Yamaha side mount control, Yamaha mechanical remote control, Yamaha 10 pin control, Yamaha 10 pin remote, Yamaha 15 foot harness control, Yamaha push to choke control, Yamaha PTT remote control, Yamaha power trim control, Yamaha throttle control, Yamaha shift control, Yamaha outboard control box, Yamaha 703-48207, Yamaha 703-48205, Yamaha 703-48201, Pro Marine 48207SP