Z6_GHK6HJC0OG6S20Q8HU3K6R0G63
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM5
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM7
Z7_GHK6HJC0OG6S20Q8HU3K6R0Q22

Johnson, Evinrude & E-TEC Outboard Parts

Shop OEM and aftermarket Johnson, Evinrude, and E-TEC outboard parts for maintenance, repair, troubleshooting, and complete engine rebuild projects. Browse marine parts by system, including cooling, fuel delivery, electrical, internal engine components, lower unit parts, steering, trim, and routine service items.

Pro Marine USA carries parts for a wide range of Johnson and Evinrude outboards, including carbureted, Ficht / FFI, and E-TEC direct-injection platforms. Use your engine horsepower, model number, serial number, or OEM part number whenever possible to confirm fitment before ordering.

Shop Johnson, Evinrude & E-TEC Parts by System

Find the Correct Johnson, Evinrude or E-TEC Part

Johnson and Evinrude parts can vary by horsepower, model number, engine family, and production range. If you are unsure which component fits your engine, use the OEM parts lookup to identify the original part number from a factory parts diagram.

Once you have the OEM part number, search Pro Marine to find available OEM and aftermarket replacement options.

Use Our OEM Parts Lookup »

Common Johnson, Evinrude & E-TEC Engine Families

Pro Marine supports many Johnson and Evinrude outboards across a wide horsepower range, including older carbureted engines and later direct-injection platforms.

  • Small Outboards: 2HP through 30HP 2-stroke and select 4-stroke applications
  • Midrange: common 35HP through 90HP carbureted and fuel-injected platforms
  • V4 and V6: popular 115HP, 135HP, 140HP, 150HP, and 175HP applications
  • High Horsepower: 200HP, 225HP, 250HP, and 300HP applications
  • Ficht / FFI: direct-injection Johnson and Evinrude engine families
  • E-TEC: Evinrude E-TEC direct-injection platforms across multiple horsepower ranges

Common Johnson & Evinrude Repair Areas

  • Engine overheating: inspect the water pump, impeller, thermostat, pressure-control components, cooling passages, and engine anodes.
  • Hard starting or rough running: inspect fuel pumps, carburetors or injectors, filters, spark plugs, ignition components, and intake sealing.
  • No spark or intermittent ignition: inspect power packs, ignition coils, stators, timer bases, sensors, wiring, and grounds.
  • Low compression or power loss: inspect pistons, rings, cylinders, reeds, bearings, gaskets, and other internal engine components.
  • Lower unit noise or water intrusion: inspect prop shaft seals, driveshaft seals, shift shaft seals, bearings, gears, and gear lube condition.
  • Trim or steering problems: inspect trim motors, hydraulic components, steering systems, hoses, seals, and related rigging parts.

Why Buy Johnson, Evinrude & E-TEC Parts from Pro Marine USA?

  • OEM and aftermarket replacement options for many Johnson, Evinrude, and E-TEC applications.
  • Parts for routine maintenance, professional repair, engine rebuilding, lower units, fuel systems, electrical systems, steering, and trim.
  • OEM diagram and part-number lookup tools to help identify the correct component before ordering.
  • Dealer pricing available for qualified marine repair businesses and dealers.
  • Large selection of older OMC-era parts and modern E-TEC service components.
  • Fast weekday shipping on qualifying in-stock orders.

Frequently Asked Questions

How do I find the correct Johnson or Evinrude outboard part?

Start with the engine horsepower, model number, production year, and serial information whenever available. Use the OEM parts lookup to identify the original part number from the factory diagram.

Can I search Johnson and Evinrude parts by OEM part number?

Yes. Enter the OEM part number into the Pro Marine site search to locate available OEM and aftermarket replacement options. If you do not know the part number, use the OEM parts lookup first.

Do Johnson and Evinrude parts vary by model and year?

Yes. Components may vary across engines with similar horsepower depending on model number, engine family, and production range. Confirm complete engine identification information before ordering.

Do you carry parts for Evinrude E-TEC engines?

Yes. Pro Marine carries parts for many Evinrude E-TEC applications, including cooling, fuel, electrical, internal engine, lower unit, steering, trim, and maintenance components.

Do you carry parts for older Johnson and Evinrude outboards?

Yes. Pro Marine carries many repair and rebuild parts for older Johnson, Evinrude, and OMC outboards, including carbureted and early fuel-injected engine families.

What Johnson and Evinrude parts are commonly replaced during routine maintenance?

Common maintenance items include spark plugs, fuel filters, water pump kits, impellers, thermostats, gear lube, drain plug seals, anodes, oil-system components, and model-specific service items.

Fitment Tip: Johnson, Evinrude, and E-TEC parts can vary by model number, horsepower, engine family, and production range. Confirm the OEM part number or complete engine identification information whenever possible before ordering.

|◀ ◀ 2317 - 2328 of 2557 ▶ ▶|
View:
13.7-16.2mm / .539-.638" Band Dim 7x0.6mm 316 SS
Item#:
4-162
Cross Reference#:
13791
8M0214911
888988015
Manufacturer Item:
8M0214911
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
7.62
Pack
14.5-17mm / .571-.669" Band Dim 7x0.6mm Stainless
Item#:
4-170
Manufacturer:
Pro Marine
Available:
Out of Stock
ETA:
12/01/2026
Your Price:
7.40
Pack
15.3-18.5mm /0.602-0.728" Band Dim 7x0.6mm Stainless
Item#:
4-185
Manufacturer:
Pro Marine
Available:
Out of Stock
ETA:
11/24/2026
Your Price:
9.59
Pack
16.6-19.8mm / .654-.780" Band Dim 7x0.6mm 316 SS
Item#:
4-198
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
9.88
Pack
MPI Black Oetiker Clamp # 4-170
Item#:
315-038
Available:
Out of Stock
Your Price:
2.49
Foot
This item is discontinued
MPI 5/16" Fuel Line for Above-Deck Marine Applications

USCG Type B1/B2 Marine Fuel Hose

MPI 5/16" Marine Fuel Hose - Type B1/B2 - Sold by the Foot

Build or replace your outboard fuel line with 5/16" USCG Type B1/B2 marine fuel hose. This MPI bulk fuel hose is sold by the foot so you can order the length required for your installation without purchasing a preassembled fuel line.

Type B marine fuel hose is commonly used in exposed and above-deck outboard fuel-line applications where Type B hose is appropriate for the installation.

Need a complete setup? Pro Marine also stocks the correct Oetiker clamp, 5/16" primer bulb, Oetiker pincer tool and a complete clamp assortment with the installation tool included.

5/16" Bulk Marine Fuel Line

Inside Diameter: 5/16"
USCG Rating: Type B1/B2
Manufacturer: MPI Products
Color: Black
Sold: By the Foot
Recommended Clamp: Oetiker 4-153
Recommended Primer Bulb: Pro Marine 8004 - 5/16"

How to Order Bulk Fuel Hose

This hose is sold by the foot. Select the quantity based on the total continuous length of hose required for your installation.

For example, if you need approximately 8 feet of fuel hose, order a quantity of 8.

What Does USCG Type B1/B2 Fuel Hose Mean?

Marine fuel hose classifications help identify where and how a hose is designed to be used within a boat's fuel system.

The "B" designation identifies marine fuel hose that does not carry the same USCG fire-test requirement as Type A hose. For that reason, Type B hose is commonly associated with exposed or above-deck fuel-line installations, while Type A hose is the appropriate choice where the installation requires the additional fire-resistant Type A classification.

The numbers "1" and "2" refer to fuel permeation performance. Type 1 is the lower-permeation classification and is the classification normally associated with fuel-feed hose intended to contain fuel continuously. Type 2 permits greater permeation and is used for applications such as certain fill and vent arrangements.

Quick Guide: Type A vs. Type B Marine Fuel Hose
Fuel Hose Type General Use Fire-Test Requirement
Type A1 Fuel-feed applications including installations requiring Type A protection Yes
Type A2 Certain fill and vent applications requiring Type A protection Yes
Type B1 Fuel-feed applications where Type B hose is permitted No Type A fire-test rating
Type B2 Certain fill and vent applications where Type B hose is permitted No Type A fire-test rating
Need Fuel Hose for an Enclosed or Below-Deck Installation?

Do not choose fuel hose based on diameter alone. The required USCG hose classification depends on where and how the hose is installed.

For installations requiring Type A1/A2 marine fuel hose, use our 5/16" Type A fuel hose instead.

View 5/16" Type A Marine Fuel Hose

Complete Your 5/16" Fuel Line Setup

The correct hose is only one part of a reliable marine fuel-line installation. Pro Marine stocks the matching clamps, primer bulb and installation tools needed to build or service your fuel line.

Oetiker 4-153 Clamp Oetiker 4-153 Ear Clamp - 10 Pack

The matching Oetiker ear clamp for this MPI 5/16" Type B fuel hose. Provides a clean, secure connection at fuel fittings and components.

View Oetiker 4-153 Clamp
5/16 Primer Bulb Pro Marine 8004 - 5/16" Primer Bulb

5/16" primer bulb for building or servicing a marine outboard fuel-line assembly using 5/16" fuel hose.

View 5/16" Primer Bulb
Oetiker Pincer Oetiker Standard Jaw Pincer Tool

Installation tool for properly closing Oetiker ear clamps when assembling marine fuel lines.

View Oetiker Pincer Tool
Oetiker Clamp Pack Pro Marine Oetiker Clamp Pack with Tool

Complete assortment containing common Oetiker clamp sizes plus the installation tool. A convenient option for marine shops, technicians and customers servicing multiple hose sizes.

View Oetiker Clamp Pack

Mercury OEM 5/16" Fuel Hose Available

Mercury OEM 5/16" Silver Fuel Hose

Prefer the Mercury factory fuel hose? Pro Marine also stocks Mercury OEM 5/16" silver fuel hose sold by the foot.

The Mercury hose uses a different outside diameter than this MPI hose and therefore requires a different Oetiker clamp: 4-145.

View Mercury OEM 5/16" Fuel Hose

View Oetiker 4-145 Clamp for Mercury Fuel Hose

Why Doesn't Every 5/16" Fuel Hose Use the Same Clamp?

5/16" identifies the hose's inside diameter, not its outside diameter. Different hose constructions can have different wall thicknesses and therefore different outside diameters.

That is why this MPI 315-056 Type B hose uses Oetiker clamp 4-153, while the Mercury OEM 5/16" silver hose uses Oetiker clamp 4-145.

Always match the clamp to the specific hose being installed rather than selecting a clamp based only on the hose's inside diameter.

What This Fuel Hose is Used For

This 5/16" bulk marine fuel hose can be used when building, repairing or replacing fuel lines in compatible marine applications where USCG Type B hose is appropriate.

Selling the hose by the foot allows boat owners and marine technicians to build the required length and add the appropriate primer bulb, connectors, fittings and clamps for the specific installation.

Building a 5/16" Outboard Fuel Line

A typical 5/16" outboard fuel-line setup may require:

  • 5/16" marine fuel hose
  • 5/16" primer bulb
  • Correct engine-side fuel fitting or connector
  • Correct tank-side fitting or connection
  • Correctly sized Oetiker ear clamps
  • Oetiker pincer tool for clamp installation

The exact components depend on the engine, fuel tank and layout of the boat's fuel system.

Key Features & Benefits

  • 5/16" inside diameter marine fuel hose
  • USCG Type B1/B2 rated hose
  • MPI Products marine fuel line
  • Designed for exposed and above-deck applications where Type B hose is permitted
  • Sold by the foot for custom-length installations
  • Matching Oetiker 4-153 clamp available
  • Compatible 5/16" primer bulb available
  • Type A 5/16" alternative available for applications requiring Type A hose
  • Mercury OEM 5/16" silver fuel hose alternative available

Need Help Choosing the Right Marine Fuel Hose?

Hose diameter is only one part of choosing the correct marine fuel line. The hose classification, installation location, fuel-system design, fittings, primer bulb and clamp size should also be considered.

Visit the Pro Marine Fuel Line Technical Center

FAQ

What size is this fuel hose?
This hose has a 5/16" inside diameter.

Is the hose sold by the foot?
Yes. Order the quantity corresponding to the number of feet needed for your installation.

What does USCG Type B mean?
Type B marine fuel hose meets the applicable SAE marine fuel-hose performance classification but does not carry the same USCG fire-test requirement as Type A hose. It is commonly used in exposed or above-deck applications where Type B hose is permitted.

What is the difference between B1 and B2?
The number identifies the hose's permeation classification. Type 1 has the lower permeation limit and is normally associated with fuel-feed applications intended to contain fuel continuously. Type 2 allows greater permeation and is used for certain other fuel-system applications.

Can I use this hose below deck?
Fuel-hose requirements depend on the installation. For enclosed or below-deck installations requiring the Type A fire-resistant classification, use the 5/16" Type A fuel hose .

Which Oetiker clamp fits this hose?
Use the Oetiker 4-153 ear clamp with this MPI 315-056 hose.

Which primer bulb fits this hose?
The Pro Marine 8004 5/16" Primer Bulb is the matching hose size.

Do you sell a Mercury OEM 5/16" fuel hose?
Yes. Pro Marine stocks Mercury OEM 5/16" silver fuel hose by the foot. The Mercury hose uses Oetiker clamp 4-145 rather than the 4-153 clamp used with this MPI hose.

Why are there different clamps for two 5/16" hoses?
The 5/16" measurement refers to inside diameter. Hose outside diameter can vary depending on wall thickness and construction, so the correct Oetiker clamp must be matched to the specific hose.

Dealer Discounts & Store Policies

Dealer / Marine Industry Discounts

Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.

Apply for a Dealer Account

Shipping Policy

  • Free shipping on orders over $100 continental U.S.
  • Orders ship via UPS, USPS, and FedEx.
  • Orders received before 5:30 PM EST ship the same business day.
  • Typical delivery time is 1-5 business days.

30-Day Return Policy

  • Returns accepted within 30 days of delivery.
  • Parts must be new, unused, and in original packaging.
  • Installed parts are not returnable.
  • Return authorization is required before sending items back.

Need help with a return or order question?
Contact Us
Phone: 941-721-3000


Searchable Terms

315-056, MPI 315-056, 5/16 fuel hose, 5/16 marine fuel hose, 5/16 boat fuel line, 5/16 outboard fuel hose, USCG Type B fuel hose, Type B1 fuel hose, Type B2 fuel hose, marine fuel line by the foot, bulk marine fuel hose, above deck fuel hose, outboard fuel line, boat fuel hose, Oetiker 4-153, 4-153 fuel hose clamp, 5/16 primer bulb, marine primer bulb, Mercury 5/16 fuel hose, Type A marine fuel hose, Type B marine fuel hose

Item#:
315-056
Manufacturer:
MPI Products
Available:
In Stock
Your Price:
2.50
Foot
40.8-44mm / 1.59-1.72" Band Dim 7x0.6mm 316 SS
Item#:
4-440
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
13.52
Pack
10.3 - 12.8mm / .406-.504" Band Dim 7x0.6mm 316 SS
Item#:
4-128
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
7.62
Pack
9.8 - 12.3 mm / .386-.484" Band Dim 7x0.6mm 316 SS
Item#:
4-123
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
7.62
Pack
12-14.5mm / .472-.571" Band Dim 7x0.6mm 316 SS
Item#:
4-145
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
7.62
Pack
11.5-14mm / .453-.551" Band Dim 7x0.6mm Stainless
Item#:
4-140
Cross Reference#:
0346931
0769074
346931
769074
850241
Manufacturer Item:
769074
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
7.94
Pack
min to max 65-89mm/ 2.54-3.47" 316 Stainless Steel
Item#:
4-14C
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
2.67
Pack
|◀ ◀ 2317 - 2328 of 2557 ▶ ▶|
View: