Z6_GHK6HJC0OG6S20Q8HU3K6R0G63
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM5
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM7
Z7_GHK6HJC0OG6S20Q8HU3K6R0Q22

Suzuki Outboard Parts

Shop OEM and aftermarket Suzuki outboard parts for DF-series FourStroke engines. Find repair, service, lower unit, fuel and engine rebuild parts.

Pro Marine USA carries Suzuki outboard engine parts for maintenance, troubleshooting, repair, and complete rebuild projects. Browse parts by engine system, or use your model, horsepower, serial number, or OEM part number whenever possible to confirm fitment before ordering.

Shop Suzuki Outboard Parts by System

Find the Correct Suzuki Outboard Part

Suzuki outboard parts can vary by model, horsepower, production range, and engine family. If you are unsure which component fits your engine, use the OEM parts lookup to locate the original Suzuki part number from a factory parts diagram.

Once you have the OEM part number, search Pro Marine to find available genuine Suzuki and aftermarket replacement options.

Use Our OEM Parts Lookup »

Common Suzuki Outboard Engine Families

Pro Marine supports many popular Suzuki DF-series outboards across a wide horsepower range. Always confirm the exact engine model and identification information before ordering parts.

  • Portable and Midrange: Suzuki DF2.5 through DF60 FourStroke applications
  • Inline Four-Cylinder: common DF70 through DF140 engine families
  • Mid- and High-Horsepower: DF150, DF175, DF200, DF225, and DF250 applications
  • High-Horsepower Offshore: DF300, DF325, and DF350 platforms
  • FourStroke EFI: electronically fuel-injected Suzuki outboards across most modern DF-series applications

Common Suzuki Outboard Repair Areas

  • Engine overheating: inspect the water pump, impeller, thermostat, cooling passages, pressure-control components, and engine anodes.
  • Hard starting or rough running: inspect fuel pumps, filters, injectors, spark plugs, ignition components, sensors, and intake sealing.
  • Charging or electrical problems: inspect ignition coils, rectifier/regulators, sensors, wiring, grounds, and charging-system components.
  • Low compression or power loss: inspect pistons, rings, cylinder condition, valves, bearings, gaskets, and internal engine components.
  • Lower unit noise or water intrusion: inspect prop shaft seals, driveshaft seals, shift shaft seals, bearings, gears, and gear lube condition.
  • Trim or steering problems: inspect trim motors, hydraulic components, steering systems, hoses, seals, and related rigging parts.

Why Buy Suzuki Outboard Parts from Pro Marine USA?

  • OEM Suzuki and aftermarket replacement options for many common applications.
  • Parts for routine maintenance, professional repair, complete engine rebuilds, lower units, fuel systems, electrical systems, steering, and trim.
  • OEM diagram and part-number lookup tools to help identify the correct component before ordering.
  • Dealer pricing available for qualified marine repair businesses and dealers.
  • Large selection of Suzuki service kits, engine parts, lower unit components, cooling parts, and fuel system products.
  • Fast weekday shipping on qualifying in-stock orders.

Frequently Asked Questions

How do I find the correct Suzuki outboard part?

Start with the engine model, horsepower, production information, and any available serial or identification numbers. Use the OEM parts lookup to identify the original Suzuki part number whenever possible.

Can I search Suzuki parts by OEM part number?

Yes. Enter the Suzuki OEM part number into the Pro Marine site search to locate available OEM and aftermarket replacement options. If you do not know the part number, use the OEM parts lookup first.

Do Suzuki outboard parts vary by model and year?

Yes. Suzuki may use different components across engines with similar horsepower depending on model, engine family, and production range. Confirm the complete engine identification information before ordering.

Do you carry parts for Suzuki DF300, DF325, and DF350 outboards?

Yes. Pro Marine carries parts for many Suzuki high-horsepower DF-series applications, including routine maintenance, cooling, fuel, electrical, internal engine, lower unit, steering, and trim components.

Do you carry both OEM and aftermarket Suzuki parts?

Yes. Pro Marine offers genuine Suzuki parts along with aftermarket replacement parts for many common Suzuki outboard maintenance, repair, and rebuild applications.

What Suzuki outboard parts are commonly replaced during routine maintenance?

Common maintenance items include engine oil, oil filters, fuel filters, spark plugs, water pump kits, impellers, thermostats, gear lube, drain plug seals, anodes, and model-specific service kit components.

Fitment Tip: Suzuki parts can vary by model, engine family, and production range. Confirm the OEM part number or complete engine identification information whenever possible before ordering.

|◀ ◀ 373 - 384 of 1065 ▶ ▶|
View:
Includes 2 Quarts ECSTAR 10W40, OEM Suzuki Filter & Drain Washer

Suzuki DF25 DF25V DF30A Oil Change Kit

Suzuki DF25 DF25V DF30A Oil Change Kit With ECSTAR 10W40

The DF2530-OC Suzuki oil change kit includes the maintenance components required to perform a complete engine oil service on compatible Suzuki DF25, DF25V, and DF30A outboards.

This kit includes 2 quarts of Suzuki ECSTAR V7000 10W40 Semi-Synthetic Marine Engine Oil, an OEM Suzuki oil filter, and the required oil drain screw gasket / washer.

Compatible Applications

Manufacturer Model Oil Included
Suzuki DF25 2 Quarts
Suzuki DF25V 2 Quarts
Suzuki DF30A 2 Quarts
Important Fitment Note:

This oil change kit is designed for Suzuki DF25, DF25V, and DF30A outboards.

The included 2 quarts of Suzuki ECSTAR 10W40 oil is sufficient for most routine oil change services on these engines. Always verify your owner's manual oil capacity before performing maintenance.

What is Included

Qty Part Description
2 Suzuki ECSTAR V7000 10W40 Oil - Quart 2 quarts semi-synthetic marine engine oil
1 OEM Suzuki Oil Filter 7915-1 OEM Suzuki oil filter
1 Oil Drain Screw Gasket / Washer 5030465 Required drain screw sealing washer for engine oil service

Recommended Gear Lube

Gear lube is not included in this kit. Many owners perform lower unit service at the same time as an engine oil change.

Suzuki Marine Gear Lube

Premium Suzuki gear lube for lower unit maintenance and gearcase protection.

View Suzuki Gear Lube

Need Additional Engine Oil?

Additional Suzuki ECSTAR V7000 10W40 oil is available separately if needed.

View Suzuki ECSTAR 10W40 Oil - Quart

About Suzuki ECSTAR V7000 10W40

ECSTAR V7000 Semi-Synthetic Marine Engine Oil combines advanced synthetic lubricants with premium mineral oils to provide excellent wear protection, corrosion resistance, and long-term reliability in marine environments.

Benefits of ECSTAR Marine Oil

  • Helps reduce engine wear
  • Lower oil consumption
  • Improved cold starting performance
  • Reduced fuel consumption
  • Excellent corrosion protection
  • Engineered specifically for Suzuki marine engines

What This Kit is Used For

This kit provides the engine oil, oil filter, and drain washer needed for routine oil service on Suzuki DF25, DF25V, and DF30A outboards.

Regular oil changes help extend engine life and maintain performance while replacing the drain screw gasket / washer helps ensure a proper seal after service.

Key Features and Benefits

  • Oil change kit for Suzuki DF25, DF25V, and DF30A outboards
  • Includes 2 quarts of Suzuki ECSTAR V7000 10W40 oil
  • Includes OEM Suzuki oil filter 7915-1
  • Includes oil drain screw gasket / washer 5030465
  • Uses genuine Suzuki maintenance components where noted
  • Gear lube available separately
  • Convenient all-in-one maintenance package

Service Kit Details

  • Part Number: DF2530-OC
  • Application: Suzuki DF25, DF25V, DF30A
  • Oil Included: Yes
  • Oil Quantity: 2 Quarts
  • Oil Type: Suzuki ECSTAR V7000 10W40 Semi-Synthetic
  • Oil Filter Included: Yes - OEM Suzuki Filter 7915-1
  • Drain Washer Included: Yes - 5030465
  • Gear Lube Included: No

FAQ

What models does this kit fit?
Suzuki DF25, DF25V, and DF30A outboards.

How much oil is included?
This kit includes 2 quarts of Suzuki ECSTAR V7000 10W40 oil.

Does this kit include an OEM Suzuki oil filter?
Yes. This kit includes OEM Suzuki oil filter 7915-1.

Does this kit include the drain washer?
Yes. The required oil drain screw gasket / washer 5030465 is included.

Does this kit include gear lube?
No. Gear lube is sold separately and can be ordered using the link above.

Can I use this for annual maintenance?
Yes. This kit is intended for routine scheduled oil change service.

Dealer Discounts & Store Policies

Dealer / Marine Industry Discounts

Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.

Apply for a Dealer Account

Shipping Policy

  • Free shipping on orders over $100 continental U.S.
  • Orders ship via UPS, USPS, and FedEx.
  • Orders received before 5:30 PM EST ship the same business day.
  • Typical delivery time is 1-5 business days.

30-Day Return Policy

  • Returns accepted within 30 days of delivery.
  • Parts must be new, unused, and in original packaging.
  • Opened oil products may not be returnable.
  • Return authorization is required before sending items back.

Need help with a return or order question?
Contact Us
Phone: 941-721-3000


Searchable Terms

DF2530-OC, Suzuki DF25 oil change kit, Suzuki DF25V oil change kit, Suzuki DF30A oil change kit, Suzuki DF25 maintenance kit, Suzuki DF30A maintenance kit, Suzuki ECSTAR 10W40, SUZ-10W40-QT, 7915-1, OEM Suzuki oil filter, 5030465, Suzuki drain washer, Suzuki oil drain gasket, Suzuki oil drain washer, Suzuki gear lube, SUZ-GLUBE-QT, Suzuki outboard maintenance kit, Suzuki DF25 service kit, Suzuki DF30A service kit

Item#:
DF2530-OC
Manufacturer:
Suzuki
Available:
In Stock
Your Price:
40.48
Each
OEM Suzuki Water Outlet Gasket for Select DF150-DF300 Outboards

OEM Suzuki Water Outlet Gasket

Suzuki Cooling System Water Outlet Gasket

This genuine OEM Suzuki water outlet gasket is used on select Suzuki DF-series outboards within the engine cooling system water outlet assembly.

The gasket helps create a proper seal between the water outlet housing and cooling system components to help prevent cooling system leaks and maintain proper engine water circulation.

Compatible Applications

Engine Range Engine Type System Application Notes
Suzuki DF150 FourStroke Cooling System Used in compatible water outlet housing assemblies
Suzuki DF175 FourStroke Cooling System Used in compatible water outlet housing assemblies
Suzuki DF200 FourStroke Cooling System Used in compatible water outlet housing assemblies
Suzuki DF225 FourStroke Cooling System Used in compatible cooling system applications
Suzuki DF250 FourStroke Cooling System Used in compatible cooling system applications
Suzuki DF300 FourStroke Cooling System Used in compatible cooling system applications
Johnson / Evinrude Select Rebadged Suzuki Models Cooling System Cross references BRP part number 5035048
Fitment Note: This gasket fits select Suzuki DF-series cooling system water outlet assemblies and cross references Johnson / Evinrude OEM part number 5035048.

Always verify your engine model, serial number, and cooling system diagram before ordering engine gaskets and seals.

OEM Part Numbers & Cross References

Brand Part Number
Suzuki OEM 17582-93J00
Johnson / Evinrude 5035048
Alternate Search Format 1758293J00

What This Water Outlet Gasket is Used For

This gasket is used in the cooling system water outlet assembly on compatible Suzuki DF-series outboards.

The gasket helps seal mating surfaces within the cooling system to help maintain proper water circulation and cooling system pressure.

A worn or damaged cooling system gasket may allow water leaks, improper sealing, or cooling performance issues.

Replacing cooling system gaskets during service or repair helps maintain reliable engine cooling system operation.

Key Features and Benefits

  • Genuine OEM Suzuki cooling system gasket
  • Fits select Suzuki DF150-DF300 outboards
  • Used in compatible water outlet housing assemblies
  • Cross references Johnson / Evinrude part number 5035048
  • Helps maintain proper cooling system sealing
  • Helps reduce cooling system leaks
  • OEM fit and material compatibility
  • Sold individually

Water Outlet Gasket Details

  • Brand: Suzuki
  • Part Type: Water Outlet Gasket
  • OEM Part Number: 17582-93J00
  • Cross Reference: Johnson / Evinrude 5035048
  • Application: Suzuki DF-Series Cooling Systems
  • System: Engine Cooling System
  • Quantity Sold: Each

FAQ

What engines does this gasket fit?
This gasket fits select Suzuki DF150 through DF300 outboards using compatible cooling system water outlet assemblies.

What does this gasket seal?
It seals the water outlet housing area within the outboard cooling system.

Does this cross reference Johnson / Evinrude part numbers?
Yes. This Suzuki gasket cross references Johnson / Evinrude OEM part number 5035048.

Can a damaged water outlet gasket cause cooling system leaks?
Yes. A worn or damaged gasket may allow water leakage or improper cooling system sealing.

Should I verify my serial number before ordering?
Yes. Suzuki used different cooling system components depending on model and production range, so diagram verification is recommended.

Dealer Discounts & Store Policies

Dealer / Marine Industry Discounts

Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.

Apply for a Dealer Account

Shipping Policy

  • Free shipping on orders over $100 continental U.S.
  • Orders ship via UPS, USPS, and FedEx.
  • Orders received before 5:30 PM EST ship the same business day.
  • Typical delivery time is 1–5 business days.

30-Day Return Policy

  • Returns accepted within 30 days of delivery.
  • Cooling system gaskets should be installed only after confirming correct fitment.
  • Items must be new, unused, and in original packaging.
  • Return authorization is required before sending items back.

Need help with a return or order question?
Contact Us
Phone: 941-721-3000


Searchable Terms

17582-93J00, 1758293J00, 5035048, Suzuki water outlet gasket, Suzuki cooling gasket, Suzuki DF150 gasket, Suzuki DF175 gasket, Suzuki DF200 gasket, Suzuki DF225 gasket, Suzuki DF250 gasket, Suzuki DF300 gasket, Suzuki cooling system gasket, Suzuki water housing gasket, Johnson Evinrude 5035048, outboard cooling gasket

Item#:
17582-93J00
Cross Reference#:
17582-93J00
18-0793
5035048
Manufacturer Item:
17582-93J00
Manufacturer:
Suzuki
Available:
In Stock
Your Price:
2.83
Each
Item#:
18-7947
Cross Reference#:
17670-ZW1-030GH
9-37812
Manufacturer Item:
17670-ZW1-030GH
Manufacturer:
Sierra
Available:
In Stock
Your Price:
28.39
Each
YamahaVZ150-VZ300 F150-F350 Suzuki DF200-DF350
Item#:
6324P
Cross Reference#:
15412-93J10
18-79809
6P3-WS24A-00-00
6P3-WS24A-01-00
6P3-WS24A-02-00
6P3-24563-00-00
6P3-24563-01-00
6P3-24563-02-00
6324
8M0154756
Manufacturer Item:
6P3-WS24A-01-00
Manufacturer:
Pro Marine
Available:
Out of Stock
ETA:
01/10/2027
Your Price:
20.09
Each
Suzuki/OMC
Item#:
18-3499
Cross Reference#:
15170-93E00
15170-99E0V
15170-99E00
15170-99E1V
5030699
5032321
Manufacturer Item:
15170-99E00
Manufacturer:
Sierra
Available:
In Stock
Your Price:
51.79
Each
Suzuki 2 & 4 Strk 3.5-25hp Johnson/Evinrude 4-70hp 4 Strk
Item#:
1-31-15410985
Cross Reference#:
0778228
15410-98500
18-7719
5032238
778228
Manufacturer Item:
15410-98500
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
6.04
Each
Suzuki DF60-DF70 2001-09 Johnson / Evinrude 60-70hp 4 Stroke
Item#:
1-34-66D00
Cross Reference#:
15710-66D00
5032693
Manufacturer Item:
15710-66D00
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
106.72
Each
Suzuki 90-140hp Johnson 90-140hp
Item#:
S2093M
Cross Reference#:
18-6831
31100-90J00
31100-90J01
5033799
Manufacturer Item:
31100-90J01
Manufacturer:
MES Marine
Available:
In Stock
Your Price:
585.45
Each
Suzuki DF40/50 1999-2010 Johnson 40 / 50hp 1999-2006
Item#:
131541087JP
Cross Reference#:
15410-87J00
18-8622
270000510
270000612
270000633
270000669
270000688
270000882
270001011
270001077
270001099
5031400
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
37.93
Each
Johnson 200-300HP Suzuki DF200-DF300 4-stroke
Johnson 200-225hp 4 Stroke
Suzuki DF200-DF300 4 Stroke
Item#:
4985P
Cross Reference#:
0769403
15440-90J00
15440-93J00
5034985
769403
Manufacturer Item:
5034985
Manufacturer:
Pro Marine
Available:
Out of Stock
ETA:
01/10/2027
Your Price:
47.37
Each
4 Stroke Outboards Including Johnson Evinrude 140 HP - OEM 11141-92J00

Pro Marine Aftermarket Suzuki and Johnson Evinrude Engine Components

Pro Marine Cylinder Head Gasket for Suzuki DF100A DF115A DF140 DF140A and Johnson Evinrude 140 HP Outboards

The Pro Marine 9214 Cylinder Head Gasket is an aftermarket replacement for select Suzuki DF100A, DF115A, DF140, and DF140A 4-stroke outboard engines, along with compatible Johnson and Evinrude 140 HP 4-stroke outboards.

This replacement head gasket cross references Suzuki OEM part numbers 11141-92J00 and 11141-92J01, as well as Johnson Evinrude BRP OEM numbers 5033908 and 5034644.

The cylinder head gasket is installed between the engine block and cylinder head. It provides the sealing interface required to maintain combustion chamber compression while separating the engine's cooling and lubrication passages.

Applications include earlier Suzuki DF140, DF140T, and DF140Z engines listed from 2002-2010, later Suzuki DF100A, DF115A, and DF140A engine configurations, and the specific Johnson Evinrude 140 HP models listed below.

Important: Verify the original OEM head gasket number and your engine model and serial number before ordering. Not every Suzuki 100-140 HP or Johnson Evinrude 140 HP outboard uses this gasket.

Product Information

  • Pro Marine Part Number: 9214
  • Brand: Pro Marine Aftermarket
  • Product Type: Cylinder Head Gasket
  • Suzuki OEM Cross References: 11141-92J00, 11141-92J01
  • Johnson Evinrude BRP Cross References: 5033908, 5034644
  • Engine Manufacturers: Suzuki, Johnson, Evinrude
  • Engine Type: 4-Stroke Outboard
  • Suzuki Horsepower: 100 HP, 115 HP, and 140 HP
  • Johnson Evinrude Horsepower: 140 HP
  • Suzuki Engine Families: DF100A, DF115A, DF140, DF140A
  • Additional Suzuki Variations: DF100AT, DF115AST, DF115AT, DF115AZ, DF115ST, DF140T, DF140Z, DF140AT, DF140AZ
  • Earlier Suzuki DF140 Applications: 2002-2010
  • Later Suzuki Applications: Listed DF100A, DF115A, and DF140A configurations
  • Installation Location: Between Cylinder Head and Engine Block
  • Condition: New

OEM and Cross Reference Numbers

Pro Marine 9214 is an aftermarket replacement for the following Suzuki and Johnson Evinrude cylinder head gasket part numbers.

Manufacturer Part Number Description
Pro Marine 9214 Aftermarket Cylinder Head Gasket
Suzuki OEM 11141-92J00 Cylinder Head Gasket Cross Reference
Suzuki OEM 11141-92J01 Cylinder Head Gasket Cross Reference
Johnson Evinrude BRP OEM 5033908 Cylinder Head Gasket Cross Reference
Johnson Evinrude BRP OEM 5034644 Cylinder Head Gasket Cross Reference

These numbers are provided to help identify the correct replacement when searching by Suzuki, Johnson, Evinrude, or BRP original equipment part numbers.

What This Part Is Used For

The cylinder head gasket creates a seal between the cylinder head and engine block of a compatible 4-stroke outboard engine.

It helps maintain combustion chamber pressure while separating cooling water, engine oil, and combustion passages.

A damaged head gasket may allow combustion gases or engine fluids to leak across sealing surfaces, potentially resulting in compression loss, overheating, or internal engine contamination.

Common Repair Applications

  • Suzuki DF100A 100 HP cylinder head repairs
  • Suzuki DF115A 115 HP cylinder head repairs
  • Suzuki DF140 140 HP cylinder head repairs
  • Suzuki DF140A 140 HP cylinder head repairs
  • Johnson 140 HP 4-stroke cylinder head repairs
  • Evinrude 140 HP 4-stroke cylinder head repairs
  • Replacement of damaged or leaking head gaskets
  • Engine repairs requiring cylinder head removal
  • Internal engine rebuilding and service

Important Fitment Note

Pro Marine 9214 replaces the listed Suzuki and Johnson Evinrude OEM head gasket numbers.

Suzuki DF140 engines from the earlier 2002-2010 applications are listed separately from the later DF140A engine family. The supplied compatibility data also includes select DF100A and DF115A applications.

Suzuki model letters and serial number references help distinguish engine configurations. Compatibility should be confirmed using the exact engine identification information.

Do not assume compatibility with every Suzuki 100 HP, 115 HP, or 140 HP engine or every Johnson Evinrude 140 HP outboard. Verify the required OEM gasket number.

Compatible Outboard Applications

The following tables organize the supplied Suzuki and Johnson Evinrude fitment into readable engine families and model groups.

Suzuki DF100A - 100 HP 4-Stroke

Engine Model Catalog Applications Serial References
DF100A 2013 and additional listed configurations -510001
10003F-310001
11503F-310001
11503Z-310001
710001
DF100AT Listed T configurations 10003F-040001
10003F-710001

Suzuki DF115A - 115 HP 4-Stroke

Engine Model Catalog Applications Serial References
DF115A 2013 and additional listed configurations -510001
10003F-310001
11503F-310001
11503Z-310001
710001
DF115AST Listed ST configurations 11504F-040001
11504F-710001
DF115AT Listed T configurations 11503F-040001
11503F-710001
DF115AZ Listed Z configurations 11503Z-040001
11503Z-710001
DF115ST Listed ST application -510001

Suzuki DF140 - 140 HP 4-Stroke - 2002-2010

The earlier Suzuki DF140 engine family includes the standard DF140 and the listed DF140T and DF140Z variations.

Engine Model Compatible Years Additional References
DF140 2002-2010 14002F-210001
14002Z-210001
DF140T 2002-2010 T model configurations
DF140Z 2002-2010 Z model configurations

Suzuki DF140A - 140 HP 4-Stroke

The supplied application data also includes the later Suzuki DF140A engine family, with a 2013 catalog listing and additional model and serial configurations.

Engine Model Catalog Applications Serial References
DF140A 2013 and additional listed configurations -510001
14003F-310001
14003Z-310001
710001
DF140AT Listed T configurations 14003F-040001
14003F-710001
DF140AZ Listed Z configurations 14003Z-040001
14003Z-710001

Johnson and Evinrude 140 HP 4-Stroke Outboards

Pro Marine 9214 is also listed for the following Johnson and Evinrude 140 HP 4-stroke engine model numbers.

The model numbers are grouped to make identification easier while preserving the supplied application references.

Model Group Compatible Model Numbers Application
BJ140 Models BJ140CX4SRS
BJ140PL4SRS
BJ140PX4SRS
BJ140CX4SOC
BJ140PL4SOC
BJ140PX4SOC
BJ140CX4DR
BJ140L4SDR
BJ140X4SDR
Listed 140 HP 4-stroke BJ-series configurations.
J140CX Models J140CX4SOR
J140CX4SRC
J140CX4STS
J140CX4SDA
Listed 140 HP 4-stroke CX-series configurations.
J140PL Models J140PL4SOR
J140PL4SRC
J140PL4STS
J140PL4SDA
Listed 140 HP 4-stroke PL-series configurations.
J140PX Models J140PX4SOR
J140PX4SRS
J140PX4STS
J140PX4SDA
Listed 140 HP 4-stroke PX-series configurations.

Johnson Evinrude Fitment Information

The supplied Johnson Evinrude compatibility data includes both J140 and BJ140 model designations.

The listed models are 140 HP 4-stroke outboard applications. Exact model identification is important when selecting replacement engine components.

Note: Specific production years were not supplied for these model numbers. Verify compatibility using the complete model number and corresponding BRP parts diagram.

Common Symptoms of a Failed Head Gasket

A damaged cylinder head gasket may allow combustion pressure, cooling water, or engine oil to leak between internal engine passages.

Possible symptoms include:

  • Loss of cylinder compression
  • Engine overheating
  • Cooling water entering a combustion chamber
  • Water contamination in engine oil
  • Rough running or misfiring
  • Reduced engine power
  • Difficulty starting
  • Combustion gases entering the cooling system
  • Visible damage to the original head gasket
Diagnostic Reminder

These symptoms may also result from other engine problems. Perform appropriate diagnostic testing before concluding that the cylinder head gasket requires replacement.

Installation and Service Tips

Cylinder head gasket replacement requires removal of the cylinder head and inspection of the engine's sealing surfaces. Follow the applicable Suzuki or Johnson Evinrude service manual for the exact engine model.

Recommended Installation Practices

  • Confirm the original Suzuki or BRP OEM gasket number.
  • Verify the engine model and serial number.
  • Allow the engine to cool completely before disassembly.
  • Remove the cylinder head according to the applicable service manual.
  • Inspect the cylinder head and engine block sealing surfaces.
  • Check for warpage, corrosion, cracks, and other damage.
  • Remove old gasket material without damaging the sealing surfaces.
  • Keep debris out of cylinders, oil passages, and cooling passages.
  • Install the replacement gasket in the correct orientation.
  • Follow the manufacturer's specified tightening sequence and torque procedure.
  • Replace additional seals or fasteners when required by the service manual.
  • Inspect the cooling system for conditions that may have caused the original failure.
  • Check engine operation and cooling performance after reassembly.

Important Cylinder Head Installation Warning

Correct gasket installation requires proper surface preparation, cylinder head inspection, and the correct fastener tightening procedure.

Do not install a replacement head gasket over warped, cracked, or improperly prepared sealing surfaces. Improper installation can cause compression loss, cooling water leakage, overheating, and engine damage.

Key Features and Benefits

  • Pro Marine Aftermarket Replacement: Alternative to the listed Suzuki and Johnson Evinrude OEM head gaskets.
  • Suzuki 100-140 HP Applications: Listed for select DF100A, DF115A, DF140, and DF140A 4-stroke outboards.
  • Johnson Evinrude Compatibility: Fits the specified 140 HP 4-stroke model applications.
  • Engine Repair Component: Used during compatible cylinder head repairs and engine rebuilding.
  • Combustion Chamber Sealing: Provides the gasket interface between the cylinder head and engine block.
  • Cooling and Lubrication Passage Sealing: Helps maintain separation between internal engine passages.
  • Multiple OEM Cross References: Suzuki 11141-92J00 and 11141-92J01, plus BRP 5033908 and 5034644.
  • Dealer Pricing Available: Qualified marine repair businesses can apply for wholesale pricing.

Frequently Asked Questions

What Suzuki OEM part numbers does Pro Marine 9214 replace?

Pro Marine 9214 cross references Suzuki 11141-92J00 and 11141-92J01.

What Johnson Evinrude OEM numbers does this gasket replace?

This gasket cross references BRP 5033908 and 5034644.

Does this head gasket fit Suzuki DF100A outboards?

Yes. It is listed for select Suzuki DF100A 100 HP 4-stroke applications, including DF100A and DF100AT configurations.

Does this head gasket fit Suzuki DF115A outboards?

Yes. It is listed for select Suzuki DF115A 115 HP 4-stroke applications, including DF115A, DF115AST, DF115AT, and DF115AZ configurations. The supplied fitment also includes a DF115ST application.

Does this gasket fit Suzuki DF140 outboards from 2002-2010?

Yes. The supplied fitment includes Suzuki DF140, DF140T, and DF140Z 140 HP 4-stroke applications from 2002-2010.

Does this gasket fit Suzuki DF140A outboards?

Yes. It is listed for select Suzuki DF140A 140 HP 4-stroke applications, including DF140A, DF140AT, and DF140AZ configurations.

Does this gasket fit Johnson and Evinrude 140 HP outboards?

Yes. It is listed for the specific Johnson Evinrude 140 HP 4-stroke model numbers shown in the compatibility table.

Will this gasket fit every Suzuki 100-140 HP outboard?

No. Compatibility is limited to the listed engine models using the corresponding OEM head gasket numbers. Other Suzuki engine families may require different gaskets.

What does a cylinder head gasket do?

The cylinder head gasket seals the joint between the cylinder head and engine block. It helps maintain compression while separating combustion, cooling, and lubrication passages.

What are common symptoms of a blown head gasket?

Possible symptoms include compression loss, overheating, rough running, water intrusion, and engine oil contamination. Proper diagnostic testing is required to confirm the cause.

Should I replace the head gasket after removing the cylinder head?

Yes. Install a new compatible cylinder head gasket when reassembling the engine after cylinder head removal.

Is Pro Marine 9214 a genuine Suzuki or BRP OEM gasket?

No. Pro Marine 9214 is an aftermarket replacement for the listed Suzuki and Johnson Evinrude OEM part numbers.

Can I install this head gasket myself?

Cylinder head gasket replacement requires engine disassembly, inspection of sealing surfaces, and proper tightening procedures. Professional installation is recommended.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies genuine OEM and aftermarket marine engine parts, cylinder head gaskets, internal engine components, rebuild parts, and maintenance products to marine repair shops, dealerships, technicians, and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on orders over $100 within the continental United States.
  • In-stock orders received before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options available through UPS, USPS, and FedEx.
  • Typical delivery time is 1-5 business days.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused, and in original packaging.
  • Installed parts are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Confirming Head Gasket Fitment?

If you are unsure whether Pro Marine 9214 is the correct cylinder head gasket for your Suzuki, Johnson, or Evinrude outboard, contact Pro Marine with your engine model and serial number.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

9214, 11141-92J00, 11141-92J01, 1114192J00, 1114192J01, 5033908, 5034644

Searchable Terms

Pro Marine 9214, Suzuki 11141-92J00, Suzuki 11141-92J01, Suzuki 1114192J00, Suzuki 1114192J01, Johnson Evinrude 5033908, Johnson Evinrude 5034644, Suzuki head gasket, Suzuki cylinder head gasket, Suzuki DF100A head gasket, Suzuki DF100AT head gasket, Suzuki DF115A head gasket, Suzuki DF115AST head gasket, Suzuki DF115AT head gasket, Suzuki DF115AZ head gasket, Suzuki DF115ST head gasket, Suzuki DF140 head gasket, Suzuki DF140T head gasket, Suzuki DF140Z head gasket, Suzuki DF140A head gasket, Suzuki DF140AT head gasket, Suzuki DF140AZ head gasket, Suzuki 100HP head gasket, Suzuki 115HP head gasket, Suzuki 140HP head gasket, Suzuki 4 stroke head gasket, Suzuki 100-140 HP cylinder head gasket, Johnson 140HP head gasket, Evinrude 140HP head gasket, Johnson Evinrude 140HP 4 stroke, Johnson Evinrude cylinder head gasket, BRP head gasket, J140CX4SOR head gasket, J140CX4SRC head gasket, J140CX4STS head gasket, J140CX4SDA head gasket, J140PL4SOR head gasket, J140PL4SRC head gasket, J140PL4STS head gasket, J140PL4SDA head gasket, J140PX4SOR head gasket, J140PX4SRS head gasket, J140PX4STS head gasket, J140PX4SDA head gasket, BJ140CX4SRS head gasket, BJ140PL4SRS head gasket, BJ140PX4SRS head gasket, BJ140CX4SOC head gasket, BJ140PL4SOC head gasket, BJ140PX4SOC head gasket, BJ140CX4DR head gasket, BJ140L4SDR head gasket, BJ140X4SDR head gasket, Suzuki outboard engine repair, Suzuki cylinder head repair, Suzuki engine rebuild parts, Johnson Evinrude engine rebuild parts, aftermarket Suzuki head gasket, aftermarket Johnson Evinrude head gasket, Pro Marine Suzuki engine parts

Item#:
9214
Cross Reference#:
11141-92J00
11141-92J01
5033908
5034644
Manufacturer Item:
11141-92J01
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
69.00
Each
Pro Marine Aftermarket for Suzuki 1999-2010 and Johnson Evinrude 4 Stroke

Pro Marine Aftermarket Suzuki and Johnson Evinrude Engine Components

Pro Marine Cylinder Head Gasket for Suzuki DF40 DF50 and Johnson Evinrude 40-50 HP 4-Stroke Outboards

The Pro Marine 8741 Cylinder Head Gasket is an aftermarket replacement for select Suzuki DF40 and DF50 40-50 HP 4-stroke outboards from 1999-2010, along with compatible Johnson and Evinrude 40 HP and 50 HP 4-stroke outboard engines.

This replacement head gasket cross references Suzuki OEM part numbers 11141-87J00, 11141-87J01, and 11141-87J02, as well as Johnson Evinrude BRP OEM numbers 5031293 and 5034353.

Installed between the cylinder head and engine block, the gasket provides the sealing interface required to maintain combustion chamber compression while separating the engine's cooling and lubrication passages.

Pro Marine 8741 is suitable for compatible cylinder head repairs, head gasket replacement, and engine rebuilding applications. It is an aftermarket alternative to the listed genuine OEM gasket numbers.

Important: This gasket is intended for the listed Suzuki DF40 and DF50 engine families and compatible Johnson Evinrude 40-50 HP 4-stroke models. Confirm the engine model and original OEM gasket number before ordering.

Product Information

  • Pro Marine Part Number: 8741
  • Brand: Pro Marine Aftermarket
  • Product Type: Cylinder Head Gasket
  • Suzuki OEM Cross References: 11141-87J00, 11141-87J01, 11141-87J02
  • Johnson Evinrude BRP Cross References: 5031293, 5034353
  • Engine Manufacturers: Suzuki, Johnson, Evinrude
  • Engine Type: 4-Stroke Outboard
  • Horsepower: 40 HP and 50 HP
  • Suzuki Engine Families: DF40, DF40QH, DF40TL, DF50, DF50QH, DF50TL
  • Suzuki Model Years: 1999-2010 on Listed Applications
  • Johnson Evinrude Applications: Select 40 HP and 50 HP 4-Stroke Models
  • Installation Location: Between Cylinder Head and Engine Block
  • Condition: New

OEM and Cross Reference Numbers

Pro Marine 8741 is an aftermarket replacement for the following Suzuki and Johnson Evinrude cylinder head gasket part numbers.

Manufacturer Part Number Description
Pro Marine 8741 Aftermarket Cylinder Head Gasket
Suzuki OEM 11141-87J00 Cylinder Head Gasket Cross Reference
Suzuki OEM 11141-87J01 Cylinder Head Gasket Cross Reference
Suzuki OEM 11141-87J02 Cylinder Head Gasket Cross Reference
Johnson Evinrude BRP OEM 5031293 Cylinder Head Gasket Cross Reference
Johnson Evinrude BRP OEM 5034353 Cylinder Head Gasket Cross Reference

These part numbers are provided to help customers identify the correct replacement when searching by original Suzuki, Johnson, Evinrude, or BRP numbers.

What This Part Is Used For

The cylinder head gasket seals the connection between the engine block and cylinder head of a 4-stroke outboard engine.

The gasket helps maintain combustion chamber pressure while separating the engine's cooling water and oil passages.

When a head gasket fails, combustion pressure or engine fluids may leak across sealing surfaces. Depending on the failure location, this can lead to compression loss, overheating, water intrusion, or other engine problems.

Common Repair Applications

  • Suzuki DF40 40 HP 4-stroke cylinder head repairs
  • Suzuki DF50 50 HP 4-stroke cylinder head repairs
  • Johnson 40 HP 4-stroke cylinder head repairs
  • Johnson 50 HP 4-stroke cylinder head repairs
  • Evinrude 40 HP 4-stroke cylinder head repairs
  • Evinrude 50 HP 4-stroke cylinder head repairs
  • Replacement of leaking or damaged head gaskets
  • Cylinder head removal and reinstallation
  • Engine rebuilding and internal engine repairs

Important Fitment Note

Pro Marine 8741 is intended for the earlier Suzuki DF40 and DF50 4-stroke engine families, along with the listed Johnson Evinrude 40-50 HP 4-stroke models.

The Suzuki applications supplied for this gasket cover 1999-2010, depending on the engine model.

This gasket should not be confused with head gaskets used on the later Suzuki DF40A, DF50A, and DF60A engine families.

Suzuki DF40 and DF50 engines are not the same application family as DF40A and DF50A engines. The correct gasket must be selected using the OEM part number and engine identification.

For Johnson and Evinrude applications, verify the exact model number and corresponding BRP OEM gasket number. Not every Johnson or Evinrude 40-50 HP outboard uses this gasket.

Compatible Outboard Applications

Pro Marine 8741 is listed for select Suzuki DF40 and DF50 outboards and compatible Johnson Evinrude 40 HP and 50 HP 4-stroke engines.

Suzuki DF40 and DF50 4-Stroke Outboards

The following table summarizes the supplied Suzuki fitment by engine family and model year range.

Suzuki Model Horsepower Compatible Years Engine Type
DF40 40 HP 1999-2010 4-Stroke
DF40QH 40 HP 1999-2007 4-Stroke
DF40TL 40 HP 1999-2007 4-Stroke
DF50 50 HP 1999-2010 4-Stroke
DF50QH 50 HP 1999-2007 4-Stroke
DF50TL 50 HP 1999-2007 4-Stroke

Johnson and Evinrude 40 HP and 50 HP 4-Stroke Outboards

This gasket also cross references BRP OEM numbers 5031293 and 5034353 and is listed for the following Johnson and Evinrude 4-stroke outboard models.

Brand Horsepower Model Numbers Application Details
Johnson 40 HP BJ40PL4SDR
BJ40PL4SOC
BJ40PL4SRS
J40PL4SDE
J40PL4SNF
J40PL4SOB
J40PL4SRM
J40PL4STC
4-stroke applications.
J40PL4SNF is listed as a 2002 remote-control, 20-inch shaft model with power trim and tilt.
Johnson 50 HP BJ50PL4SDR
BJ50PL4SOC
BJ50PL4SRS
J50PL4SDE
J50PL4SNF
J50PL4SOB
J50PL4SRM
J50PL4STC
4-stroke applications.
J50PL4SNF is listed as a 2002 remote-control, 20-inch shaft model with power trim and tilt.
Evinrude 40 HP E40PL4EES
E40PL4SIR
E40PL4SSC
E40PL4EES - 1999
E40PL4SSC - 2000
E40PL4SIR - 2001
4-stroke applications. SIR and SSC models are listed with electric start, power trim and tilt, and 20-inch shaft.
Evinrude 50 HP E50PL4EES
E50PL4SIR
E50PL4SSC
E50PL4EES - 1999
E50PL4SSC - 2000
E50PL4SIR - 2001
4-stroke applications. SIR and SSC models are listed with electric start, power trim and tilt, and 20-inch shaft.

Understanding Suzuki and Johnson Evinrude Fitment

Suzuki DF40: 40 HP 4-stroke outboard engine family listed from 1999-2010.

Suzuki DF50: 50 HP 4-stroke outboard engine family listed from 1999-2010.

QH and TL Models: Additional Suzuki DF40 and DF50 configurations listed from 1999-2007.

Johnson and Evinrude: Select 40 HP and 50 HP 4-stroke outboard engines using the listed BRP OEM gasket numbers.

Important: Confirm the exact model number and original gasket reference before ordering.

Common Symptoms of a Failed Head Gasket

A damaged head gasket can allow combustion pressure, cooling water, or engine oil to leak between internal engine passages.

The following conditions may indicate a cylinder head gasket problem.

  • Loss of cylinder compression
  • Engine overheating
  • Cooling water entering a combustion chamber
  • Water contamination in engine oil
  • Rough running or misfiring
  • Reduced engine performance
  • Difficulty starting
  • Combustion gases entering the cooling system
  • Visible gasket damage during engine disassembly
Diagnostic Reminder

These symptoms can also be caused by other engine problems. Perform appropriate diagnostic testing before determining that the head gasket requires replacement.

Installation and Service Tips

Replacing a cylinder head gasket requires removal of the cylinder head and inspection of the engine's sealing surfaces. Follow the applicable Suzuki or Johnson Evinrude service manual.

Recommended Installation Practices

  • Confirm the original OEM gasket number.
  • Verify the engine model and applicable year.
  • Allow the engine to cool before disassembly.
  • Remove the cylinder head following the service manual.
  • Inspect the cylinder head and block sealing surfaces.
  • Check for warpage, corrosion, cracks, or damage.
  • Remove old gasket material without damaging sealing surfaces.
  • Keep debris out of the cylinders and internal passages.
  • Install the replacement gasket in the correct orientation.
  • Follow the specified cylinder head fastener tightening sequence.
  • Use the required fastener tightening specifications.
  • Replace other gaskets and seals when required by the repair procedure.
  • Inspect the cooling system for conditions that may have caused the original failure.
  • Check engine operation and cooling performance after reassembly.

Important Cylinder Head Installation Warning

Correct gasket installation requires proper surface preparation, cylinder head inspection, and the correct fastener tightening procedure.

Do not install a new head gasket over warped, cracked, or improperly prepared sealing surfaces. Improper installation can result in compression loss, cooling water leakage, overheating, and engine damage.

Key Features and Benefits

  • Pro Marine Aftermarket Replacement: Alternative to the listed Suzuki and Johnson Evinrude OEM head gaskets.
  • Suzuki 40-50 HP Applications: Listed for DF40 and DF50 4-stroke outboards from 1999-2010.
  • Johnson Evinrude Compatibility: Fits the specified 40 HP and 50 HP 4-stroke model applications.
  • Engine Repair Component: Used during compatible cylinder head repairs and engine rebuilding.
  • Combustion Chamber Sealing: Provides the gasket interface between the cylinder head and engine block.
  • Cooling and Lubrication Passage Sealing: Helps maintain separation between internal engine passages.
  • Multiple OEM Cross References: Search using Suzuki 11141-87J00, 11141-87J01, 11141-87J02, or BRP 5031293 and 5034353.
  • Dealer Pricing Available: Qualified marine repair businesses can apply for wholesale pricing.

Frequently Asked Questions

What Suzuki OEM numbers does Pro Marine 8741 replace?

Pro Marine 8741 cross references 11141-87J00, 11141-87J01, and 11141-87J02.

What Johnson Evinrude OEM numbers does this gasket replace?

This gasket cross references 5031293 and 5034353.

Does this head gasket fit Suzuki DF40 outboards?

Yes. It is listed for Suzuki DF40 40 HP 4-stroke outboards from 1999-2010, along with DF40QH and DF40TL variants from 1999-2007.

Does this head gasket fit Suzuki DF50 outboards?

Yes. It is listed for Suzuki DF50 50 HP 4-stroke outboards from 1999-2010, along with DF50QH and DF50TL variants from 1999-2007.

Does this gasket fit Johnson 40 HP and 50 HP outboards?

Yes. The supplied fitment includes select Johnson 40 HP and 50 HP 4-stroke engines, including the listed J40, J50, BJ40, and BJ50 model numbers.

Does this gasket fit Evinrude 40 HP and 50 HP outboards?

Yes. It is listed for select Evinrude 40 HP and 50 HP 4-stroke engines, including E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4SIR, and E50PL4SSC.

Will this gasket fit Suzuki DF40A or DF50A outboards?

This gasket is listed for the earlier DF40 and DF50 engine families, not the later DF40A and DF50A applications. Always confirm the OEM gasket number before ordering.

What is the difference between Suzuki DF40 and DF40A head gaskets?

Suzuki DF40 and DF40A engines belong to different application families and may use different cylinder head gaskets. Pro Marine 8741 cross references Suzuki 11141-87J00, 11141-87J01, and 11141-87J02. Select the gasket that matches the engine's OEM parts diagram.

What does a cylinder head gasket do?

The cylinder head gasket seals the joint between the engine block and cylinder head, helping maintain compression and separation between combustion, cooling, and lubrication passages.

What are symptoms of a blown head gasket?

Possible symptoms include compression loss, overheating, rough running, water intrusion, and contamination of engine oil. Proper diagnostic testing is required to confirm the cause.

Should I replace the head gasket after removing the cylinder head?

Yes. Install a new compatible cylinder head gasket when reassembling the engine after cylinder head removal.

Is Pro Marine 8741 a genuine Suzuki or BRP OEM gasket?

No. Pro Marine 8741 is an aftermarket replacement for the listed Suzuki and Johnson Evinrude OEM part numbers.

Can I install this head gasket myself?

Cylinder head gasket replacement requires engine disassembly, inspection of sealing surfaces, and proper fastener tightening. Professional installation is recommended.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies genuine OEM and aftermarket marine engine parts, cylinder head gaskets, internal engine components, rebuild parts, and maintenance products to marine repair shops, dealerships, technicians, and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on orders over $100 within the continental United States.
  • In-stock orders received before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options available through UPS, USPS, and FedEx.
  • Typical delivery time is 1-5 business days.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused, and in original packaging.
  • Installed parts are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Confirming Head Gasket Fitment?

If you are unsure whether Pro Marine 8741 is the correct cylinder head gasket for your Suzuki, Johnson, or Evinrude outboard, contact Pro Marine with your engine model and serial number.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

8741, 11141-87J00, 11141-87J01, 11141-87J02, 1114187J00, 1114187J01, 1114187J02, 5031293, 5034353

Searchable Terms

Pro Marine 8741, Suzuki 11141-87J00, Suzuki 11141-87J01, Suzuki 11141-87J02, Johnson Evinrude 5031293, Johnson Evinrude 5034353, Suzuki head gasket, Suzuki cylinder head gasket, Suzuki DF40 head gasket, Suzuki DF50 head gasket, Suzuki DF40QH head gasket, Suzuki DF40TL head gasket, Suzuki DF50QH head gasket, Suzuki DF50TL head gasket, Suzuki 40HP head gasket, Suzuki 50HP head gasket, Suzuki 4 stroke head gasket, Suzuki 1999 head gasket, Suzuki 2000 head gasket, Suzuki 2001 head gasket, Suzuki 2002 head gasket, Suzuki 2003 head gasket, Suzuki 2004 head gasket, Suzuki 2005 head gasket, Suzuki 2006 head gasket, Suzuki 2007 head gasket, Suzuki 2008 head gasket, Suzuki 2009 head gasket, Suzuki 2010 head gasket, Johnson 40HP head gasket, Johnson 50HP head gasket, Evinrude 40HP head gasket, Evinrude 50HP head gasket, Johnson 4 stroke head gasket, Evinrude 4 stroke head gasket, Johnson Evinrude cylinder head gasket, BRP head gasket, J40PL4SNF head gasket, J50PL4SNF head gasket, E40PL4EES head gasket, E40PL4SIR head gasket, E40PL4SSC head gasket, E50PL4EES head gasket, E50PL4SIR head gasket, E50PL4SSC head gasket, Suzuki outboard engine repair, Suzuki cylinder head repair, Suzuki engine rebuild parts, Johnson Evinrude engine rebuild parts, aftermarket Suzuki head gasket, aftermarket Johnson Evinrude head gasket, Pro Marine Suzuki engine parts

Item#:
8741
Cross Reference#:
11141-87J00
11141-87J01
11141-87J02
5031293
5034353
Manufacturer Item:
11141-87J02
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
60.76
Each
|◀ ◀ 373 - 384 of 1065 ▶ ▶|
View: