S2K Commerce - Products Dropdown
Actions
S2K Commerce - Order Entry
Actions
Engine Rebuild Kit 1100K OMC Johnson Evinrude 40-60 HP 2-Cylinder
The Pro Marine 1100K Engine Rebuild Kit includes the major internal components required to rebuild Johnson and Evinrude 2-cylinder outboard engines in the 40-60 horsepower range.
This standard bore rebuild kit is designed for engines using a 3.187" cylinder bore and is commonly used during a full powerhead rebuild to restore compression, reliability, and performance.
Compatibility
This rebuild kit fits select Johnson and Evinrude 2-cylinder 2-stroke outboard engines in the 40-60 HP range.
| Brand | Application | HP / Engine | Fuel System | Notes |
|---|---|---|---|---|
| Johnson | Outboard | 40-60 HP | Carbureted | 2 Cylinder 2-Stroke 3.187" Bore |
| Evinrude | Outboard | 40-60 HP | Carbureted | 2 Cylinder 2-Stroke 3.187" Bore |
Application Chart
| Brand | Engine Type | Horsepower | Cylinders | Bore |
|---|---|---|---|---|
| Johnson | Outboard | 40 HP | 2 Cylinder | 3.187" |
| Johnson | Outboard | 50 HP | 2 Cylinder | 3.187" |
| Johnson | Outboard | 55 HP | 2 Cylinder | 3.187" |
| Johnson | Outboard | 60 HP | 2 Cylinder | 3.187" |
| Evinrude | Outboard | 40 HP | 2 Cylinder | 3.187" |
| Evinrude | Outboard | 50 HP | 2 Cylinder | 3.187" |
| Evinrude | Outboard | 55 HP | 2 Cylinder | 3.187" |
| Evinrude | Outboard | 60 HP | 2 Cylinder | 3.187" |
Engine Model Compatibility
This rebuild kit fits many Johnson and Evinrude 2-cylinder outboards using the 3.187" bore powerhead.
- J40ELCTS
- J40TLCTS
- J40ELCRD
- J40TLCRD
- J50ELCTS
- J50TLCTS
- J50ELCRD
- J50TLCRD
- E50ESL
- E50TEL
- J60ELCTS
- J60TLCTS
- J60ELCRD
- J60TLCRD
- E60ESL
- E60TLCOS
Johnson and Evinrude model numbers vary by shaft length, trim configuration, steering type, and production year. Always verify your engine model number before ordering parts.
What Is Included
The Pro Marine 1100K rebuild kit includes the primary internal components required for a complete powerhead rebuild.
- Pistons
- Piston ring sets
- Wrist pins
- Piston circlips
- Rod bearings
- Upper main crankshaft bearing
- Center main crankshaft bearing
- Lower main crankshaft bearing
- Complete powerhead gasket set
- Oil seals
- O-rings
- Intake gaskets
- Exhaust gaskets
- Cylinder head gaskets
Part Numbers & Cross References
| Reference Type | Part Number |
|---|---|
| Pro Marine Part | 1100K |
What This Kit Is Used For
Engine rebuild kits like the 1100K are used when rebuilding Johnson and Evinrude 2-stroke outboards that have experienced piston wear, ring failure, bearing damage, or loss of compression.
Replacing pistons, bearings, gaskets, and seals during a powerhead rebuild helps restore compression, improve reliability, and extend engine life.
FAQ
What engines does this rebuild kit fit?
Johnson and Evinrude 40-60 HP 2-cylinder outboards using a 3.187" bore.
Does this rebuild kit include pistons and rings?
Yes. Pistons, piston rings, wrist pins, and circlips are included.
Are crankshaft bearings included?
Yes. Upper, center, and lower main crankshaft bearings are included.
Does the kit include gaskets and seals?
Yes. The kit includes a complete powerhead gasket set along with seals and O-rings.
Dealer & Customer Support
Are you a marine repair shop, boat dealer, marina, or parts retailer? Pro Marine offers wholesale pricing and dealer discounts for qualified businesses in the marine industry.
If you work in the marine industry and regularly purchase outboard engine parts, we invite you to apply for a Pro Marine Dealer Account.
Contact Pro Marine
Phone: 941-721-3000
Contact Us Online
Shipping Information
- Free shipping on orders over $100
- Continental United States
- Ships via UPS, USPS, or FedEx
- Orders placed before 5:30 PM EST typically ship the same day
- Typical delivery time is 1-5 business days
Return Policy
Pro Marine accepts returns within 30 days of purchase on new, unused parts in original packaging.
If you are unsure about compatibility before ordering, please contact our team and we will help confirm the correct part for your engine.
Searchable Part Numbers
Pro Marine Part: 1100K
Common Searches:
Johnson 40 rebuild kit
Johnson 50 rebuild kit
Johnson 55 rebuild kit
Johnson 60 rebuild kit
Evinrude 40 rebuild kit
Evinrude 50 rebuild kit
Evinrude 55 rebuild kit
Evinrude 60 rebuild kit
OMC 2 cylinder rebuild kit
64E-43898-09-00
3C8611810M
3C8611811
3C8611811M
3C8611812
3C8611812M
3C8013030M
3C8013031
3C8013031M
3C8013034
3C8013034M
3C8023120M
3C8023122
3C8023122M
Flexible Wraparound Outboard Rigging Protection
1.5" Wrappable Split Braided Rigging Tube - F6N150
Pro Marine F6N150 is a 1.5" black wrappable split braided rigging tube supplied in a 5-foot length.
The split, wraparound design allows this protective sleeve to be installed around existing outboard wiring, hoses and cables without disconnecting the entire engine rigging bundle.
It is a useful option for rerigging, cleanup and abrasion protection when traditional closed rigging tube would require too much disassembly.
Nominal Size: 1.5"
Length: 5 Feet
Color: Black
Style: Wrappable Split Braided Tube
Application: Universal Marine Rigging
Manufacturer: Pro Marine
OEM or Aftermarket: Aftermarket
What This Rigging Tube is Used For
F6N150 wraps around an existing marine rigging bundle to help organize and protect wiring, hoses and cables.
Depending on the boat and engine setup, it may be used around:
- Engine wiring harnesses
- Battery cables
- Control cables
- Fuel hose
- Hydraulic steering hoses
- Gauge and network wiring
- Trim wiring
- Accessory wiring
Why Choose Wrappable Braided Rigging Tube?
The main advantage of a wrappable split sleeve is that the engine does not have to be completely disconnected just to install the protective covering.
The sleeve opens along its length, wraps around the existing bundle and provides a cleaner finished appearance while helping reduce direct abrasion and snagging.
It is especially useful when:
- The engine is already fully rigged
- You want to clean up exposed wiring and hoses
- Traditional closed rigging tube would be difficult to install
- You want flexible protection around an existing bundle
- You are repairing or rerouting an older transom installation
The braided sleeve should wrap around the wiring and hoses without tightly squeezing fuel hose, steering hoses or control cables.
If the 1.5" size is too small for the bundle, use the 2" F6N200 wrappable braided tube instead.
Need the 2" Braided Version?
Larger 2" wraparound braided rigging tube for cable and hose bundles that need more room than the 1.5" F6N150 provides.
View 2" Braided Rigging TubeSplit Conduit Rigging Tube Options
If you prefer a split conduit style instead of braided wrap, Pro Marine stocks both 1.5" and 2" split-conduit options.
1.5" Split Conduit - SPLITTUBING-15
1.5" split-conduit alternative for wrapping around an existing outboard rigging bundle.
View 1.5" Split Conduit
2" Split Conduit - SPLITTUBING-2
Larger split-conduit option for bulkier engine wiring and hose bundles.
View 2" Split ConduitTraditional 2" Rigging Tube Options
For new installations where the cables and hoses can be fed through a closed tube, Pro Marine also stocks traditional 2" marine rigging tube.
2" Black Rigging Tube - RIGTUBE-B
Traditional black 2" outboard rigging tube sold by the foot for clean new or fully accessible installations.
View Black 2" Rigging Tube
2" White Rigging Tube - RIGTUBE-W
White 2" traditional rigging tube for installations where a lighter color better matches the hull, transom or outboard.
View White 2" Rigging TubeWhich Rigging Tube Style Should I Use?
| Style | Installation | Best Use | Sizes |
|---|---|---|---|
| Wrappable Braided Tube | Wraps around existing rigging | Flexible protection and clean cable organization | 1.5" and 2" |
| Split Conduit | Wraps around existing rigging | Existing installations, repairs and rerigging | 1.5" and 2" |
| Traditional Rigging Tube | Rigging is fed through a closed tube | New installations and finished transom rigging | 2" Black and White |
Related Rigging Hardware
2" Transom Flange - TFLANGE-2
Standard flange for traditional 2" rigging-tube transom installations.
View Transom Flange
2" T-Flange with Fuel Port - TFLANGE-FP
Transom flange with a separate fuel-hose port for compatible outboard rigging installations.
View Fuel Port Flange
2" Rigging Hose Union - TUNION
Connects two compatible sections of traditional 2" rigging hose for extensions and repairs.
View Rigging Hose UnionInstallation Tips
- Measure the complete rigging bundle before choosing the sleeve size.
- Wrap the braided sleeve around the existing bundle instead of disconnecting the engine rigging.
- Do not tightly compress fuel hose, steering hoses or control cables.
- Leave sufficient slack for full outboard steering movement.
- Check full trim and tilt travel before finalizing the installation.
- Avoid excessively tight bends in the finished rigging bundle.
- Inspect the wiring and hoses for existing damage before covering them.
- Replace damaged wiring or hoses rather than using the sleeve to conceal damage.
When Should a Wrappable Rigging Sleeve Be Replaced?
Inspect the braided tube whenever the engine rigging is serviced.
Replacement may be needed if you find:
- Torn or heavily worn braided material
- Severe abrasion
- Sections that no longer stay wrapped around the bundle
- Exposed wiring or hoses
- A rigging bundle that has become too large for the 1.5" sleeve
Key Features and Benefits
- 1.5" wrappable split braided rigging tube
- 5-foot length
- Black finish
- Universal marine application
- Pro Marine aftermarket product
- Installs around existing engine rigging
- Helps organize wiring, cables and hoses
- Helps protect exposed rigging from abrasion and snagging
- 2" braided version available for larger bundles
- Split conduit and traditional rigging-tube alternatives available
FAQ
What size is F6N150?
F6N150 is a 1.5" wrappable split braided rigging tube.
How long is F6N150?
Pro Marine lists F6N150 as a 5-foot length.
What color is it?
F6N150 is black.
Who manufactures F6N150?
F6N150 is a Pro Marine aftermarket product.
Do I have to disconnect my engine wiring to install it?
The wrappable split design allows it to be installed around an existing
rigging bundle, which can reduce the need to disconnect hoses and wiring.
What if 1.5" is too small?
Use the
F6N200 2" Wrappable Split Braided Tube
for larger bundles.
Do you also stock split conduit?
Yes. Pro Marine stocks
1.5" split conduit
and
2" split conduit
.
Do you carry traditional rigging tube?
Yes. Pro Marine stocks
2" black rigging tube
and
2" white rigging tube
.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 continental U.S.
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1-5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Parts must be new, unused, and in original packaging.
- Installed parts are not returnable.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Terms
F6N150, 1.5 inch braided rigging tube, 1-1/2 inch rigging sleeve, wrappable rigging tube, split braided tube, outboard rigging sleeve, marine cable protection, outboard wiring sleeve, 5 foot rigging tube, F6N200, SPLITTUBING-15, SPLITTUBING-2, RIGTUBE-B, RIGTUBE-W, TFLANGE-2, TFLANGE-FP, TUNION
290260723
290260728
290260728
290430110
290430110
290931540
290931760
290931765
420260723
420260728
420430110
420931540
420931765
0173312
0777351
173312
18-8074
39729334059
777351
9-38018
420888135