Z6_GHK6HJC0OG6S20Q8HU3K6R0G63
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM5
Z7_GHK6HJC0OG6S20Q8HU3K6R0GM7
Z7_GHK6HJC0OG6S20Q8HU3K6R0Q22

Johnson, Evinrude & E-TEC Outboard Parts

Shop OEM and aftermarket Johnson, Evinrude, and E-TEC outboard parts for maintenance, repair, troubleshooting, and complete engine rebuild projects. Browse marine parts by system, including cooling, fuel delivery, electrical, internal engine components, lower unit parts, steering, trim, and routine service items.

Pro Marine USA carries parts for a wide range of Johnson and Evinrude outboards, including carbureted, Ficht / FFI, and E-TEC direct-injection platforms. Use your engine horsepower, model number, serial number, or OEM part number whenever possible to confirm fitment before ordering.

Shop Johnson, Evinrude & E-TEC Parts by System

Find the Correct Johnson, Evinrude or E-TEC Part

Johnson and Evinrude parts can vary by horsepower, model number, engine family, and production range. If you are unsure which component fits your engine, use the OEM parts lookup to identify the original part number from a factory parts diagram.

Once you have the OEM part number, search Pro Marine to find available OEM and aftermarket replacement options.

Use Our OEM Parts Lookup »

Common Johnson, Evinrude & E-TEC Engine Families

Pro Marine supports many Johnson and Evinrude outboards across a wide horsepower range, including older carbureted engines and later direct-injection platforms.

  • Small Outboards: 2HP through 30HP 2-stroke and select 4-stroke applications
  • Midrange: common 35HP through 90HP carbureted and fuel-injected platforms
  • V4 and V6: popular 115HP, 135HP, 140HP, 150HP, and 175HP applications
  • High Horsepower: 200HP, 225HP, 250HP, and 300HP applications
  • Ficht / FFI: direct-injection Johnson and Evinrude engine families
  • E-TEC: Evinrude E-TEC direct-injection platforms across multiple horsepower ranges

Common Johnson & Evinrude Repair Areas

  • Engine overheating: inspect the water pump, impeller, thermostat, pressure-control components, cooling passages, and engine anodes.
  • Hard starting or rough running: inspect fuel pumps, carburetors or injectors, filters, spark plugs, ignition components, and intake sealing.
  • No spark or intermittent ignition: inspect power packs, ignition coils, stators, timer bases, sensors, wiring, and grounds.
  • Low compression or power loss: inspect pistons, rings, cylinders, reeds, bearings, gaskets, and other internal engine components.
  • Lower unit noise or water intrusion: inspect prop shaft seals, driveshaft seals, shift shaft seals, bearings, gears, and gear lube condition.
  • Trim or steering problems: inspect trim motors, hydraulic components, steering systems, hoses, seals, and related rigging parts.

Why Buy Johnson, Evinrude & E-TEC Parts from Pro Marine USA?

  • OEM and aftermarket replacement options for many Johnson, Evinrude, and E-TEC applications.
  • Parts for routine maintenance, professional repair, engine rebuilding, lower units, fuel systems, electrical systems, steering, and trim.
  • OEM diagram and part-number lookup tools to help identify the correct component before ordering.
  • Dealer pricing available for qualified marine repair businesses and dealers.
  • Large selection of older OMC-era parts and modern E-TEC service components.
  • Fast weekday shipping on qualifying in-stock orders.

Frequently Asked Questions

How do I find the correct Johnson or Evinrude outboard part?

Start with the engine horsepower, model number, production year, and serial information whenever available. Use the OEM parts lookup to identify the original part number from the factory diagram.

Can I search Johnson and Evinrude parts by OEM part number?

Yes. Enter the OEM part number into the Pro Marine site search to locate available OEM and aftermarket replacement options. If you do not know the part number, use the OEM parts lookup first.

Do Johnson and Evinrude parts vary by model and year?

Yes. Components may vary across engines with similar horsepower depending on model number, engine family, and production range. Confirm complete engine identification information before ordering.

Do you carry parts for Evinrude E-TEC engines?

Yes. Pro Marine carries parts for many Evinrude E-TEC applications, including cooling, fuel, electrical, internal engine, lower unit, steering, trim, and maintenance components.

Do you carry parts for older Johnson and Evinrude outboards?

Yes. Pro Marine carries many repair and rebuild parts for older Johnson, Evinrude, and OMC outboards, including carbureted and early fuel-injected engine families.

What Johnson and Evinrude parts are commonly replaced during routine maintenance?

Common maintenance items include spark plugs, fuel filters, water pump kits, impellers, thermostats, gear lube, drain plug seals, anodes, oil-system components, and model-specific service items.

Fitment Tip: Johnson, Evinrude, and E-TEC parts can vary by model number, horsepower, engine family, and production range. Confirm the OEM part number or complete engine identification information whenever possible before ordering.

|◀ ◀ 1693 - 1704 of 2557 ▶ ▶|
View:
Johnson 200-300HP Suzuki DF200-DF300 4-stroke
Johnson 200-225hp 4 Stroke
Suzuki DF200-DF300 4 Stroke
Item#:
4985P
Cross Reference#:
0769403
15440-90J00
15440-93J00
5034985
769403
Manufacturer Item:
5034985
Manufacturer:
Pro Marine
Available:
Out of Stock
ETA:
01/10/2027
Your Price:
47.37
Each
4 Stroke Outboards Including Johnson Evinrude 140 HP - OEM 11141-92J00

Pro Marine Aftermarket Suzuki and Johnson Evinrude Engine Components

Pro Marine Cylinder Head Gasket for Suzuki DF100A DF115A DF140 DF140A and Johnson Evinrude 140 HP Outboards

The Pro Marine 9214 Cylinder Head Gasket is an aftermarket replacement for select Suzuki DF100A, DF115A, DF140, and DF140A 4-stroke outboard engines, along with compatible Johnson and Evinrude 140 HP 4-stroke outboards.

This replacement head gasket cross references Suzuki OEM part numbers 11141-92J00 and 11141-92J01, as well as Johnson Evinrude BRP OEM numbers 5033908 and 5034644.

The cylinder head gasket is installed between the engine block and cylinder head. It provides the sealing interface required to maintain combustion chamber compression while separating the engine's cooling and lubrication passages.

Applications include earlier Suzuki DF140, DF140T, and DF140Z engines listed from 2002-2010, later Suzuki DF100A, DF115A, and DF140A engine configurations, and the specific Johnson Evinrude 140 HP models listed below.

Important: Verify the original OEM head gasket number and your engine model and serial number before ordering. Not every Suzuki 100-140 HP or Johnson Evinrude 140 HP outboard uses this gasket.

Product Information

  • Pro Marine Part Number: 9214
  • Brand: Pro Marine Aftermarket
  • Product Type: Cylinder Head Gasket
  • Suzuki OEM Cross References: 11141-92J00, 11141-92J01
  • Johnson Evinrude BRP Cross References: 5033908, 5034644
  • Engine Manufacturers: Suzuki, Johnson, Evinrude
  • Engine Type: 4-Stroke Outboard
  • Suzuki Horsepower: 100 HP, 115 HP, and 140 HP
  • Johnson Evinrude Horsepower: 140 HP
  • Suzuki Engine Families: DF100A, DF115A, DF140, DF140A
  • Additional Suzuki Variations: DF100AT, DF115AST, DF115AT, DF115AZ, DF115ST, DF140T, DF140Z, DF140AT, DF140AZ
  • Earlier Suzuki DF140 Applications: 2002-2010
  • Later Suzuki Applications: Listed DF100A, DF115A, and DF140A configurations
  • Installation Location: Between Cylinder Head and Engine Block
  • Condition: New

OEM and Cross Reference Numbers

Pro Marine 9214 is an aftermarket replacement for the following Suzuki and Johnson Evinrude cylinder head gasket part numbers.

Manufacturer Part Number Description
Pro Marine 9214 Aftermarket Cylinder Head Gasket
Suzuki OEM 11141-92J00 Cylinder Head Gasket Cross Reference
Suzuki OEM 11141-92J01 Cylinder Head Gasket Cross Reference
Johnson Evinrude BRP OEM 5033908 Cylinder Head Gasket Cross Reference
Johnson Evinrude BRP OEM 5034644 Cylinder Head Gasket Cross Reference

These numbers are provided to help identify the correct replacement when searching by Suzuki, Johnson, Evinrude, or BRP original equipment part numbers.

What This Part Is Used For

The cylinder head gasket creates a seal between the cylinder head and engine block of a compatible 4-stroke outboard engine.

It helps maintain combustion chamber pressure while separating cooling water, engine oil, and combustion passages.

A damaged head gasket may allow combustion gases or engine fluids to leak across sealing surfaces, potentially resulting in compression loss, overheating, or internal engine contamination.

Common Repair Applications

  • Suzuki DF100A 100 HP cylinder head repairs
  • Suzuki DF115A 115 HP cylinder head repairs
  • Suzuki DF140 140 HP cylinder head repairs
  • Suzuki DF140A 140 HP cylinder head repairs
  • Johnson 140 HP 4-stroke cylinder head repairs
  • Evinrude 140 HP 4-stroke cylinder head repairs
  • Replacement of damaged or leaking head gaskets
  • Engine repairs requiring cylinder head removal
  • Internal engine rebuilding and service

Important Fitment Note

Pro Marine 9214 replaces the listed Suzuki and Johnson Evinrude OEM head gasket numbers.

Suzuki DF140 engines from the earlier 2002-2010 applications are listed separately from the later DF140A engine family. The supplied compatibility data also includes select DF100A and DF115A applications.

Suzuki model letters and serial number references help distinguish engine configurations. Compatibility should be confirmed using the exact engine identification information.

Do not assume compatibility with every Suzuki 100 HP, 115 HP, or 140 HP engine or every Johnson Evinrude 140 HP outboard. Verify the required OEM gasket number.

Compatible Outboard Applications

The following tables organize the supplied Suzuki and Johnson Evinrude fitment into readable engine families and model groups.

Suzuki DF100A - 100 HP 4-Stroke

Engine Model Catalog Applications Serial References
DF100A 2013 and additional listed configurations -510001
10003F-310001
11503F-310001
11503Z-310001
710001
DF100AT Listed T configurations 10003F-040001
10003F-710001

Suzuki DF115A - 115 HP 4-Stroke

Engine Model Catalog Applications Serial References
DF115A 2013 and additional listed configurations -510001
10003F-310001
11503F-310001
11503Z-310001
710001
DF115AST Listed ST configurations 11504F-040001
11504F-710001
DF115AT Listed T configurations 11503F-040001
11503F-710001
DF115AZ Listed Z configurations 11503Z-040001
11503Z-710001
DF115ST Listed ST application -510001

Suzuki DF140 - 140 HP 4-Stroke - 2002-2010

The earlier Suzuki DF140 engine family includes the standard DF140 and the listed DF140T and DF140Z variations.

Engine Model Compatible Years Additional References
DF140 2002-2010 14002F-210001
14002Z-210001
DF140T 2002-2010 T model configurations
DF140Z 2002-2010 Z model configurations

Suzuki DF140A - 140 HP 4-Stroke

The supplied application data also includes the later Suzuki DF140A engine family, with a 2013 catalog listing and additional model and serial configurations.

Engine Model Catalog Applications Serial References
DF140A 2013 and additional listed configurations -510001
14003F-310001
14003Z-310001
710001
DF140AT Listed T configurations 14003F-040001
14003F-710001
DF140AZ Listed Z configurations 14003Z-040001
14003Z-710001

Johnson and Evinrude 140 HP 4-Stroke Outboards

Pro Marine 9214 is also listed for the following Johnson and Evinrude 140 HP 4-stroke engine model numbers.

The model numbers are grouped to make identification easier while preserving the supplied application references.

Model Group Compatible Model Numbers Application
BJ140 Models BJ140CX4SRS
BJ140PL4SRS
BJ140PX4SRS
BJ140CX4SOC
BJ140PL4SOC
BJ140PX4SOC
BJ140CX4DR
BJ140L4SDR
BJ140X4SDR
Listed 140 HP 4-stroke BJ-series configurations.
J140CX Models J140CX4SOR
J140CX4SRC
J140CX4STS
J140CX4SDA
Listed 140 HP 4-stroke CX-series configurations.
J140PL Models J140PL4SOR
J140PL4SRC
J140PL4STS
J140PL4SDA
Listed 140 HP 4-stroke PL-series configurations.
J140PX Models J140PX4SOR
J140PX4SRS
J140PX4STS
J140PX4SDA
Listed 140 HP 4-stroke PX-series configurations.

Johnson Evinrude Fitment Information

The supplied Johnson Evinrude compatibility data includes both J140 and BJ140 model designations.

The listed models are 140 HP 4-stroke outboard applications. Exact model identification is important when selecting replacement engine components.

Note: Specific production years were not supplied for these model numbers. Verify compatibility using the complete model number and corresponding BRP parts diagram.

Common Symptoms of a Failed Head Gasket

A damaged cylinder head gasket may allow combustion pressure, cooling water, or engine oil to leak between internal engine passages.

Possible symptoms include:

  • Loss of cylinder compression
  • Engine overheating
  • Cooling water entering a combustion chamber
  • Water contamination in engine oil
  • Rough running or misfiring
  • Reduced engine power
  • Difficulty starting
  • Combustion gases entering the cooling system
  • Visible damage to the original head gasket
Diagnostic Reminder

These symptoms may also result from other engine problems. Perform appropriate diagnostic testing before concluding that the cylinder head gasket requires replacement.

Installation and Service Tips

Cylinder head gasket replacement requires removal of the cylinder head and inspection of the engine's sealing surfaces. Follow the applicable Suzuki or Johnson Evinrude service manual for the exact engine model.

Recommended Installation Practices

  • Confirm the original Suzuki or BRP OEM gasket number.
  • Verify the engine model and serial number.
  • Allow the engine to cool completely before disassembly.
  • Remove the cylinder head according to the applicable service manual.
  • Inspect the cylinder head and engine block sealing surfaces.
  • Check for warpage, corrosion, cracks, and other damage.
  • Remove old gasket material without damaging the sealing surfaces.
  • Keep debris out of cylinders, oil passages, and cooling passages.
  • Install the replacement gasket in the correct orientation.
  • Follow the manufacturer's specified tightening sequence and torque procedure.
  • Replace additional seals or fasteners when required by the service manual.
  • Inspect the cooling system for conditions that may have caused the original failure.
  • Check engine operation and cooling performance after reassembly.

Important Cylinder Head Installation Warning

Correct gasket installation requires proper surface preparation, cylinder head inspection, and the correct fastener tightening procedure.

Do not install a replacement head gasket over warped, cracked, or improperly prepared sealing surfaces. Improper installation can cause compression loss, cooling water leakage, overheating, and engine damage.

Key Features and Benefits

  • Pro Marine Aftermarket Replacement: Alternative to the listed Suzuki and Johnson Evinrude OEM head gaskets.
  • Suzuki 100-140 HP Applications: Listed for select DF100A, DF115A, DF140, and DF140A 4-stroke outboards.
  • Johnson Evinrude Compatibility: Fits the specified 140 HP 4-stroke model applications.
  • Engine Repair Component: Used during compatible cylinder head repairs and engine rebuilding.
  • Combustion Chamber Sealing: Provides the gasket interface between the cylinder head and engine block.
  • Cooling and Lubrication Passage Sealing: Helps maintain separation between internal engine passages.
  • Multiple OEM Cross References: Suzuki 11141-92J00 and 11141-92J01, plus BRP 5033908 and 5034644.
  • Dealer Pricing Available: Qualified marine repair businesses can apply for wholesale pricing.

Frequently Asked Questions

What Suzuki OEM part numbers does Pro Marine 9214 replace?

Pro Marine 9214 cross references Suzuki 11141-92J00 and 11141-92J01.

What Johnson Evinrude OEM numbers does this gasket replace?

This gasket cross references BRP 5033908 and 5034644.

Does this head gasket fit Suzuki DF100A outboards?

Yes. It is listed for select Suzuki DF100A 100 HP 4-stroke applications, including DF100A and DF100AT configurations.

Does this head gasket fit Suzuki DF115A outboards?

Yes. It is listed for select Suzuki DF115A 115 HP 4-stroke applications, including DF115A, DF115AST, DF115AT, and DF115AZ configurations. The supplied fitment also includes a DF115ST application.

Does this gasket fit Suzuki DF140 outboards from 2002-2010?

Yes. The supplied fitment includes Suzuki DF140, DF140T, and DF140Z 140 HP 4-stroke applications from 2002-2010.

Does this gasket fit Suzuki DF140A outboards?

Yes. It is listed for select Suzuki DF140A 140 HP 4-stroke applications, including DF140A, DF140AT, and DF140AZ configurations.

Does this gasket fit Johnson and Evinrude 140 HP outboards?

Yes. It is listed for the specific Johnson Evinrude 140 HP 4-stroke model numbers shown in the compatibility table.

Will this gasket fit every Suzuki 100-140 HP outboard?

No. Compatibility is limited to the listed engine models using the corresponding OEM head gasket numbers. Other Suzuki engine families may require different gaskets.

What does a cylinder head gasket do?

The cylinder head gasket seals the joint between the cylinder head and engine block. It helps maintain compression while separating combustion, cooling, and lubrication passages.

What are common symptoms of a blown head gasket?

Possible symptoms include compression loss, overheating, rough running, water intrusion, and engine oil contamination. Proper diagnostic testing is required to confirm the cause.

Should I replace the head gasket after removing the cylinder head?

Yes. Install a new compatible cylinder head gasket when reassembling the engine after cylinder head removal.

Is Pro Marine 9214 a genuine Suzuki or BRP OEM gasket?

No. Pro Marine 9214 is an aftermarket replacement for the listed Suzuki and Johnson Evinrude OEM part numbers.

Can I install this head gasket myself?

Cylinder head gasket replacement requires engine disassembly, inspection of sealing surfaces, and proper tightening procedures. Professional installation is recommended.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies genuine OEM and aftermarket marine engine parts, cylinder head gaskets, internal engine components, rebuild parts, and maintenance products to marine repair shops, dealerships, technicians, and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on orders over $100 within the continental United States.
  • In-stock orders received before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options available through UPS, USPS, and FedEx.
  • Typical delivery time is 1-5 business days.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused, and in original packaging.
  • Installed parts are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Confirming Head Gasket Fitment?

If you are unsure whether Pro Marine 9214 is the correct cylinder head gasket for your Suzuki, Johnson, or Evinrude outboard, contact Pro Marine with your engine model and serial number.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

9214, 11141-92J00, 11141-92J01, 1114192J00, 1114192J01, 5033908, 5034644

Searchable Terms

Pro Marine 9214, Suzuki 11141-92J00, Suzuki 11141-92J01, Suzuki 1114192J00, Suzuki 1114192J01, Johnson Evinrude 5033908, Johnson Evinrude 5034644, Suzuki head gasket, Suzuki cylinder head gasket, Suzuki DF100A head gasket, Suzuki DF100AT head gasket, Suzuki DF115A head gasket, Suzuki DF115AST head gasket, Suzuki DF115AT head gasket, Suzuki DF115AZ head gasket, Suzuki DF115ST head gasket, Suzuki DF140 head gasket, Suzuki DF140T head gasket, Suzuki DF140Z head gasket, Suzuki DF140A head gasket, Suzuki DF140AT head gasket, Suzuki DF140AZ head gasket, Suzuki 100HP head gasket, Suzuki 115HP head gasket, Suzuki 140HP head gasket, Suzuki 4 stroke head gasket, Suzuki 100-140 HP cylinder head gasket, Johnson 140HP head gasket, Evinrude 140HP head gasket, Johnson Evinrude 140HP 4 stroke, Johnson Evinrude cylinder head gasket, BRP head gasket, J140CX4SOR head gasket, J140CX4SRC head gasket, J140CX4STS head gasket, J140CX4SDA head gasket, J140PL4SOR head gasket, J140PL4SRC head gasket, J140PL4STS head gasket, J140PL4SDA head gasket, J140PX4SOR head gasket, J140PX4SRS head gasket, J140PX4STS head gasket, J140PX4SDA head gasket, BJ140CX4SRS head gasket, BJ140PL4SRS head gasket, BJ140PX4SRS head gasket, BJ140CX4SOC head gasket, BJ140PL4SOC head gasket, BJ140PX4SOC head gasket, BJ140CX4DR head gasket, BJ140L4SDR head gasket, BJ140X4SDR head gasket, Suzuki outboard engine repair, Suzuki cylinder head repair, Suzuki engine rebuild parts, Johnson Evinrude engine rebuild parts, aftermarket Suzuki head gasket, aftermarket Johnson Evinrude head gasket, Pro Marine Suzuki engine parts

Item#:
9214
Cross Reference#:
11141-92J00
11141-92J01
5033908
5034644
Manufacturer Item:
11141-92J01
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
69.00
Each
Pro Marine Aftermarket for Suzuki 1999-2010 and Johnson Evinrude 4 Stroke

Pro Marine Aftermarket Suzuki and Johnson Evinrude Engine Components

Pro Marine Cylinder Head Gasket for Suzuki DF40 DF50 and Johnson Evinrude 40-50 HP 4-Stroke Outboards

The Pro Marine 8741 Cylinder Head Gasket is an aftermarket replacement for select Suzuki DF40 and DF50 40-50 HP 4-stroke outboards from 1999-2010, along with compatible Johnson and Evinrude 40 HP and 50 HP 4-stroke outboard engines.

This replacement head gasket cross references Suzuki OEM part numbers 11141-87J00, 11141-87J01, and 11141-87J02, as well as Johnson Evinrude BRP OEM numbers 5031293 and 5034353.

Installed between the cylinder head and engine block, the gasket provides the sealing interface required to maintain combustion chamber compression while separating the engine's cooling and lubrication passages.

Pro Marine 8741 is suitable for compatible cylinder head repairs, head gasket replacement, and engine rebuilding applications. It is an aftermarket alternative to the listed genuine OEM gasket numbers.

Important: This gasket is intended for the listed Suzuki DF40 and DF50 engine families and compatible Johnson Evinrude 40-50 HP 4-stroke models. Confirm the engine model and original OEM gasket number before ordering.

Product Information

  • Pro Marine Part Number: 8741
  • Brand: Pro Marine Aftermarket
  • Product Type: Cylinder Head Gasket
  • Suzuki OEM Cross References: 11141-87J00, 11141-87J01, 11141-87J02
  • Johnson Evinrude BRP Cross References: 5031293, 5034353
  • Engine Manufacturers: Suzuki, Johnson, Evinrude
  • Engine Type: 4-Stroke Outboard
  • Horsepower: 40 HP and 50 HP
  • Suzuki Engine Families: DF40, DF40QH, DF40TL, DF50, DF50QH, DF50TL
  • Suzuki Model Years: 1999-2010 on Listed Applications
  • Johnson Evinrude Applications: Select 40 HP and 50 HP 4-Stroke Models
  • Installation Location: Between Cylinder Head and Engine Block
  • Condition: New

OEM and Cross Reference Numbers

Pro Marine 8741 is an aftermarket replacement for the following Suzuki and Johnson Evinrude cylinder head gasket part numbers.

Manufacturer Part Number Description
Pro Marine 8741 Aftermarket Cylinder Head Gasket
Suzuki OEM 11141-87J00 Cylinder Head Gasket Cross Reference
Suzuki OEM 11141-87J01 Cylinder Head Gasket Cross Reference
Suzuki OEM 11141-87J02 Cylinder Head Gasket Cross Reference
Johnson Evinrude BRP OEM 5031293 Cylinder Head Gasket Cross Reference
Johnson Evinrude BRP OEM 5034353 Cylinder Head Gasket Cross Reference

These part numbers are provided to help customers identify the correct replacement when searching by original Suzuki, Johnson, Evinrude, or BRP numbers.

What This Part Is Used For

The cylinder head gasket seals the connection between the engine block and cylinder head of a 4-stroke outboard engine.

The gasket helps maintain combustion chamber pressure while separating the engine's cooling water and oil passages.

When a head gasket fails, combustion pressure or engine fluids may leak across sealing surfaces. Depending on the failure location, this can lead to compression loss, overheating, water intrusion, or other engine problems.

Common Repair Applications

  • Suzuki DF40 40 HP 4-stroke cylinder head repairs
  • Suzuki DF50 50 HP 4-stroke cylinder head repairs
  • Johnson 40 HP 4-stroke cylinder head repairs
  • Johnson 50 HP 4-stroke cylinder head repairs
  • Evinrude 40 HP 4-stroke cylinder head repairs
  • Evinrude 50 HP 4-stroke cylinder head repairs
  • Replacement of leaking or damaged head gaskets
  • Cylinder head removal and reinstallation
  • Engine rebuilding and internal engine repairs

Important Fitment Note

Pro Marine 8741 is intended for the earlier Suzuki DF40 and DF50 4-stroke engine families, along with the listed Johnson Evinrude 40-50 HP 4-stroke models.

The Suzuki applications supplied for this gasket cover 1999-2010, depending on the engine model.

This gasket should not be confused with head gaskets used on the later Suzuki DF40A, DF50A, and DF60A engine families.

Suzuki DF40 and DF50 engines are not the same application family as DF40A and DF50A engines. The correct gasket must be selected using the OEM part number and engine identification.

For Johnson and Evinrude applications, verify the exact model number and corresponding BRP OEM gasket number. Not every Johnson or Evinrude 40-50 HP outboard uses this gasket.

Compatible Outboard Applications

Pro Marine 8741 is listed for select Suzuki DF40 and DF50 outboards and compatible Johnson Evinrude 40 HP and 50 HP 4-stroke engines.

Suzuki DF40 and DF50 4-Stroke Outboards

The following table summarizes the supplied Suzuki fitment by engine family and model year range.

Suzuki Model Horsepower Compatible Years Engine Type
DF40 40 HP 1999-2010 4-Stroke
DF40QH 40 HP 1999-2007 4-Stroke
DF40TL 40 HP 1999-2007 4-Stroke
DF50 50 HP 1999-2010 4-Stroke
DF50QH 50 HP 1999-2007 4-Stroke
DF50TL 50 HP 1999-2007 4-Stroke

Johnson and Evinrude 40 HP and 50 HP 4-Stroke Outboards

This gasket also cross references BRP OEM numbers 5031293 and 5034353 and is listed for the following Johnson and Evinrude 4-stroke outboard models.

Brand Horsepower Model Numbers Application Details
Johnson 40 HP BJ40PL4SDR
BJ40PL4SOC
BJ40PL4SRS
J40PL4SDE
J40PL4SNF
J40PL4SOB
J40PL4SRM
J40PL4STC
4-stroke applications.
J40PL4SNF is listed as a 2002 remote-control, 20-inch shaft model with power trim and tilt.
Johnson 50 HP BJ50PL4SDR
BJ50PL4SOC
BJ50PL4SRS
J50PL4SDE
J50PL4SNF
J50PL4SOB
J50PL4SRM
J50PL4STC
4-stroke applications.
J50PL4SNF is listed as a 2002 remote-control, 20-inch shaft model with power trim and tilt.
Evinrude 40 HP E40PL4EES
E40PL4SIR
E40PL4SSC
E40PL4EES - 1999
E40PL4SSC - 2000
E40PL4SIR - 2001
4-stroke applications. SIR and SSC models are listed with electric start, power trim and tilt, and 20-inch shaft.
Evinrude 50 HP E50PL4EES
E50PL4SIR
E50PL4SSC
E50PL4EES - 1999
E50PL4SSC - 2000
E50PL4SIR - 2001
4-stroke applications. SIR and SSC models are listed with electric start, power trim and tilt, and 20-inch shaft.

Understanding Suzuki and Johnson Evinrude Fitment

Suzuki DF40: 40 HP 4-stroke outboard engine family listed from 1999-2010.

Suzuki DF50: 50 HP 4-stroke outboard engine family listed from 1999-2010.

QH and TL Models: Additional Suzuki DF40 and DF50 configurations listed from 1999-2007.

Johnson and Evinrude: Select 40 HP and 50 HP 4-stroke outboard engines using the listed BRP OEM gasket numbers.

Important: Confirm the exact model number and original gasket reference before ordering.

Common Symptoms of a Failed Head Gasket

A damaged head gasket can allow combustion pressure, cooling water, or engine oil to leak between internal engine passages.

The following conditions may indicate a cylinder head gasket problem.

  • Loss of cylinder compression
  • Engine overheating
  • Cooling water entering a combustion chamber
  • Water contamination in engine oil
  • Rough running or misfiring
  • Reduced engine performance
  • Difficulty starting
  • Combustion gases entering the cooling system
  • Visible gasket damage during engine disassembly
Diagnostic Reminder

These symptoms can also be caused by other engine problems. Perform appropriate diagnostic testing before determining that the head gasket requires replacement.

Installation and Service Tips

Replacing a cylinder head gasket requires removal of the cylinder head and inspection of the engine's sealing surfaces. Follow the applicable Suzuki or Johnson Evinrude service manual.

Recommended Installation Practices

  • Confirm the original OEM gasket number.
  • Verify the engine model and applicable year.
  • Allow the engine to cool before disassembly.
  • Remove the cylinder head following the service manual.
  • Inspect the cylinder head and block sealing surfaces.
  • Check for warpage, corrosion, cracks, or damage.
  • Remove old gasket material without damaging sealing surfaces.
  • Keep debris out of the cylinders and internal passages.
  • Install the replacement gasket in the correct orientation.
  • Follow the specified cylinder head fastener tightening sequence.
  • Use the required fastener tightening specifications.
  • Replace other gaskets and seals when required by the repair procedure.
  • Inspect the cooling system for conditions that may have caused the original failure.
  • Check engine operation and cooling performance after reassembly.

Important Cylinder Head Installation Warning

Correct gasket installation requires proper surface preparation, cylinder head inspection, and the correct fastener tightening procedure.

Do not install a new head gasket over warped, cracked, or improperly prepared sealing surfaces. Improper installation can result in compression loss, cooling water leakage, overheating, and engine damage.

Key Features and Benefits

  • Pro Marine Aftermarket Replacement: Alternative to the listed Suzuki and Johnson Evinrude OEM head gaskets.
  • Suzuki 40-50 HP Applications: Listed for DF40 and DF50 4-stroke outboards from 1999-2010.
  • Johnson Evinrude Compatibility: Fits the specified 40 HP and 50 HP 4-stroke model applications.
  • Engine Repair Component: Used during compatible cylinder head repairs and engine rebuilding.
  • Combustion Chamber Sealing: Provides the gasket interface between the cylinder head and engine block.
  • Cooling and Lubrication Passage Sealing: Helps maintain separation between internal engine passages.
  • Multiple OEM Cross References: Search using Suzuki 11141-87J00, 11141-87J01, 11141-87J02, or BRP 5031293 and 5034353.
  • Dealer Pricing Available: Qualified marine repair businesses can apply for wholesale pricing.

Frequently Asked Questions

What Suzuki OEM numbers does Pro Marine 8741 replace?

Pro Marine 8741 cross references 11141-87J00, 11141-87J01, and 11141-87J02.

What Johnson Evinrude OEM numbers does this gasket replace?

This gasket cross references 5031293 and 5034353.

Does this head gasket fit Suzuki DF40 outboards?

Yes. It is listed for Suzuki DF40 40 HP 4-stroke outboards from 1999-2010, along with DF40QH and DF40TL variants from 1999-2007.

Does this head gasket fit Suzuki DF50 outboards?

Yes. It is listed for Suzuki DF50 50 HP 4-stroke outboards from 1999-2010, along with DF50QH and DF50TL variants from 1999-2007.

Does this gasket fit Johnson 40 HP and 50 HP outboards?

Yes. The supplied fitment includes select Johnson 40 HP and 50 HP 4-stroke engines, including the listed J40, J50, BJ40, and BJ50 model numbers.

Does this gasket fit Evinrude 40 HP and 50 HP outboards?

Yes. It is listed for select Evinrude 40 HP and 50 HP 4-stroke engines, including E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4SIR, and E50PL4SSC.

Will this gasket fit Suzuki DF40A or DF50A outboards?

This gasket is listed for the earlier DF40 and DF50 engine families, not the later DF40A and DF50A applications. Always confirm the OEM gasket number before ordering.

What is the difference between Suzuki DF40 and DF40A head gaskets?

Suzuki DF40 and DF40A engines belong to different application families and may use different cylinder head gaskets. Pro Marine 8741 cross references Suzuki 11141-87J00, 11141-87J01, and 11141-87J02. Select the gasket that matches the engine's OEM parts diagram.

What does a cylinder head gasket do?

The cylinder head gasket seals the joint between the engine block and cylinder head, helping maintain compression and separation between combustion, cooling, and lubrication passages.

What are symptoms of a blown head gasket?

Possible symptoms include compression loss, overheating, rough running, water intrusion, and contamination of engine oil. Proper diagnostic testing is required to confirm the cause.

Should I replace the head gasket after removing the cylinder head?

Yes. Install a new compatible cylinder head gasket when reassembling the engine after cylinder head removal.

Is Pro Marine 8741 a genuine Suzuki or BRP OEM gasket?

No. Pro Marine 8741 is an aftermarket replacement for the listed Suzuki and Johnson Evinrude OEM part numbers.

Can I install this head gasket myself?

Cylinder head gasket replacement requires engine disassembly, inspection of sealing surfaces, and proper fastener tightening. Professional installation is recommended.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies genuine OEM and aftermarket marine engine parts, cylinder head gaskets, internal engine components, rebuild parts, and maintenance products to marine repair shops, dealerships, technicians, and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on orders over $100 within the continental United States.
  • In-stock orders received before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options available through UPS, USPS, and FedEx.
  • Typical delivery time is 1-5 business days.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused, and in original packaging.
  • Installed parts are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Confirming Head Gasket Fitment?

If you are unsure whether Pro Marine 8741 is the correct cylinder head gasket for your Suzuki, Johnson, or Evinrude outboard, contact Pro Marine with your engine model and serial number.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

8741, 11141-87J00, 11141-87J01, 11141-87J02, 1114187J00, 1114187J01, 1114187J02, 5031293, 5034353

Searchable Terms

Pro Marine 8741, Suzuki 11141-87J00, Suzuki 11141-87J01, Suzuki 11141-87J02, Johnson Evinrude 5031293, Johnson Evinrude 5034353, Suzuki head gasket, Suzuki cylinder head gasket, Suzuki DF40 head gasket, Suzuki DF50 head gasket, Suzuki DF40QH head gasket, Suzuki DF40TL head gasket, Suzuki DF50QH head gasket, Suzuki DF50TL head gasket, Suzuki 40HP head gasket, Suzuki 50HP head gasket, Suzuki 4 stroke head gasket, Suzuki 1999 head gasket, Suzuki 2000 head gasket, Suzuki 2001 head gasket, Suzuki 2002 head gasket, Suzuki 2003 head gasket, Suzuki 2004 head gasket, Suzuki 2005 head gasket, Suzuki 2006 head gasket, Suzuki 2007 head gasket, Suzuki 2008 head gasket, Suzuki 2009 head gasket, Suzuki 2010 head gasket, Johnson 40HP head gasket, Johnson 50HP head gasket, Evinrude 40HP head gasket, Evinrude 50HP head gasket, Johnson 4 stroke head gasket, Evinrude 4 stroke head gasket, Johnson Evinrude cylinder head gasket, BRP head gasket, J40PL4SNF head gasket, J50PL4SNF head gasket, E40PL4EES head gasket, E40PL4SIR head gasket, E40PL4SSC head gasket, E50PL4EES head gasket, E50PL4SIR head gasket, E50PL4SSC head gasket, Suzuki outboard engine repair, Suzuki cylinder head repair, Suzuki engine rebuild parts, Johnson Evinrude engine rebuild parts, aftermarket Suzuki head gasket, aftermarket Johnson Evinrude head gasket, Pro Marine Suzuki engine parts

Item#:
8741
Cross Reference#:
11141-87J00
11141-87J01
11141-87J02
5031293
5034353
Manufacturer Item:
11141-87J02
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
60.76
Each
Port Side 200-250 HP and Johnson Evinrude 200-225 HP Outboards

Pro Marine Aftermarket Suzuki and Johnson Evinrude V6 Engine Components

Pro Marine Port Cylinder Head Gasket for Suzuki DF200 DF225 DF250 V6 4-Stroke Outboards

The Pro Marine 9324 Port Cylinder Head Gasket is an aftermarket replacement for the port cylinder head on select Suzuki DF200, DF225, and DF250 V6 4-stroke outboards. Applications include 200 HP, 225 HP, and 250 HP Suzuki engines, along with specified Johnson and Evinrude 200 HP and 225 HP 4-stroke outboards.

This gasket cross references Suzuki OEM 11142-93J00, 11142-93J01, 11142-93J02, 11142-93J03, and 11142-93J10, along with Johnson Evinrude BRP OEM numbers 5034854, 5035971, and 5036630.

Installed between the port cylinder head and engine block, the head gasket helps maintain combustion chamber compression while sealing the engine's cooling water and lubrication passages.

Compatible applications include select Suzuki DF200, DF225, and DF250 engines from 2004-2010, additional 2013 and 2015 catalog applications, and later serial-specific model configurations.

Important: This is the PORT SIDE ONLY. The matching starboard-side cylinder head gasket is sold separately as Pro Marine 9314 .

Important: Port and Starboard Head Gaskets Are Different

Compatible Suzuki DF200, DF225, and DF250 V6 outboards use separate cylinder head gaskets for the port and starboard cylinder banks.

  • Port Side (PORT): Pro Marine 9324 - Suzuki OEM 11142-93J10
  • Starboard Side (STBD): Pro Marine 9314 - Suzuki OEM 11141-93J10

These gaskets are not interchangeable. Verify which cylinder bank is being serviced before ordering.

Product Information

  • Pro Marine Part Number: 9324
  • Brand: Pro Marine Aftermarket
  • Product Type: Cylinder Head Gasket
  • Cylinder Bank: Port (PORT)
  • Primary Suzuki OEM Reference: 11142-93J10
  • Additional Suzuki OEM References: 11142-93J00, 11142-93J01, 11142-93J02, 11142-93J03
  • Johnson Evinrude BRP References: 5034854, 5035971, 5036630
  • Engine Manufacturers: Suzuki, Johnson, Evinrude
  • Engine Type: V6 4-Stroke Outboard
  • Suzuki Horsepower: 200 HP, 225 HP, 250 HP
  • Johnson Evinrude Horsepower: 200 HP, 225 HP
  • Suzuki Engine Families: DF200, DF225, DF250
  • Additional Suzuki Variations: DF200T, DF200Z, DF225T, DF225Z, DF250T, DF250Z and listed DF250ST configurations
  • Earlier Suzuki Applications: 2004-2010
  • Additional Catalog Listings: 2013, 2015, and specified later configurations
  • Matching Starboard Gasket: Pro Marine 9314
  • Condition: New

Matching Starboard Side Cylinder Head Gasket Available

Servicing both cylinder heads on your Suzuki DF200, DF225, or DF250 V6 outboard? The matching starboard-side gasket is available separately from Pro Marine USA.

Pro Marine 9314 - STBD Cylinder Head Gasket

Matching aftermarket starboard-side cylinder head gasket for select Suzuki DF200, DF225, and DF250 V6 4-stroke outboards.

Suzuki OEM: 11141-93J10
Location: Starboard Cylinder Bank
Sold Separately

View Matching Starboard Head Gasket

OEM and Cross Reference Numbers

Pro Marine 9324 replaces the following Suzuki and Johnson Evinrude port cylinder head gasket numbers.

Manufacturer Part Number Description
Pro Marine 9324 Aftermarket Port Cylinder Head Gasket
Suzuki OEM 11142-93J00 Port Head Gasket Cross Reference
Suzuki OEM 11142-93J01 Port Head Gasket Cross Reference
Suzuki OEM 11142-93J02 Port Head Gasket Cross Reference
Suzuki OEM 11142-93J03 Port Head Gasket Cross Reference
Suzuki OEM 11142-93J10 Port Head Gasket Cross Reference
Johnson Evinrude BRP 5034854 Port Head Gasket Cross Reference
Johnson Evinrude BRP 5035971 Port Head Gasket Cross Reference
Johnson Evinrude BRP 5036630 Port Head Gasket Cross Reference

What This Part Is Used For

The port cylinder head gasket seals the connection between the port cylinder head and engine block on compatible Suzuki and Johnson Evinrude V6 outboards.

Its purpose is to maintain combustion chamber compression while separating the engine's cooling water and lubrication passages.

This gasket is used during repairs involving the port cylinder head, including head gasket replacement, cylinder head service, and compatible V6 engine rebuilding.

Common Repair Applications

  • Suzuki DF200 V6 port cylinder head repairs
  • Suzuki DF225 V6 port cylinder head repairs
  • Suzuki DF250 V6 port cylinder head repairs
  • Johnson 200 HP and 225 HP 4-stroke V6 repairs
  • Evinrude 200 HP and 225 HP 4-stroke V6 repairs
  • Replacement of a leaking or damaged port head gasket
  • Engine repairs requiring port cylinder head removal
  • Compatible V6 outboard engine rebuilding

Important Fitment Note

Pro Marine 9324 is a PORT-side cylinder head gasket for select Suzuki DF200, DF225, and DF250 V6 4-stroke outboards.

The supplied fitment includes earlier 2004-2010 Suzuki applications, additional 2013 and 2015 catalog listings, and specific later model variations identified by serial references.

Certain specialized DF250 configurations, including DF250ST applications, may require additional OEM verification. Confirm the exact port-side gasket number in the engine's parts diagram.

Do not order by horsepower alone. Verify the engine model, serial number, cylinder bank, and OEM gasket number.

Compatible Suzuki Outboard Applications

Pro Marine 9324 is listed for select Suzuki DF200, DF225, and DF250 V6 4-stroke outboard engines.

The following tables organize the supplied model and serial information into readable engine families.

Suzuki DF200 - 200 HP V6 4-Stroke

Engine Model Listed Applications Serial References
DF200 2004-2010
2013 and 2015 listings
Additional serial-specific applications
-51001
20002F-210001
20002F-310001
20002Z-210001
20002Z-310001
22503F-210001
22503F-310001
22503Z-210001
22503Z-310001
25003F-210001
25003F-310001
25003Z-210001
25003Z-310001
25004F-210001
25004F-310001
710001
DF200T 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial reference
20002F-440001
20002F-540001
20002F-640001
DF200Z 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial reference
20002Z-440001
20002Z-540001
20002Z-640001

Suzuki DF225 - 225 HP V6 4-Stroke

Engine Model Listed Applications Serial References
DF225 2004-2010
2013 and 2015 listings
Additional serial-specific applications
-51001
20002F-210001
20002F-310001
20002Z-210001
20002Z-310001
22503F-210001
22503F-310001
22503Z-210001
22503Z-310001
25003F-210001
25003F-310001
25003Z-210001
25003Z-310001
25004F-210001
25004F-310001
710001
DF225T 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
22503F-040001
22503F-440001
22503F-540001
22503F-640001
DF225Z 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
22503Z-040001
22503Z-440001
22503Z-540001
22503Z-640001

Suzuki DF250 - 250 HP V6 4-Stroke

Engine Model Listed Applications Serial References
DF250 2004-2010
2013 and 2015 listings
Additional serial-specific applications
-51001
20002F-210001
20002F-310001
20002Z-210001
20002Z-310001
22503F-210001
22503F-310001
22503Z-210001
22503Z-310001
25003F-210001
25003F-310001
25003Z-210001
25003Z-310001
25004F-210001
25004F-310001
710001
DF250T 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
25003F-040001
25003F-440001
25003F-540001
25003F-640001
DF250Z 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
25003Z-040001
25003Z-440001
25003Z-540001
25003Z-640001
DF250ST Catalog variants 020, 021, 022, 024, 025
OEM verification required
25004F-040001
25004F-440001
25004F-540001
25004F-640001

Additional Suzuki Catalog Model Identifiers

The supplied fitment includes the following model-specific catalog identifiers:

  • DF200T: 020, 021, 022, 024, 025
  • DF200Z: 020, 021, 022, 024, 025
  • DF225T: 020, 021, 022, 024, 025
  • DF225Z: 020, 021, 022, 024, 025
  • DF250T: 020, 021, 022, 024, 025
  • DF250Z: 020, 021, 022, 024, 025
  • DF250ST: 020, 021, 022, 024, 025 - verify OEM gasket number

Compatible Johnson and Evinrude Outboard Applications

Pro Marine 9324 also cross references BRP port head gasket numbers 5034854, 5035971, and 5036630.

The following Johnson Evinrude 200 HP and 225 HP 4-stroke models are included in the supplied fitment.

Engine Family Horsepower Compatible Model Numbers
J200 200 HP J200CX4SRS
J200PX4SRS
J200CX4SOC
J200PX4SOC
BJ200 200 HP BJ200CX4SDC
BJ200X4SDC
BJ200CX4SO
BJ200PX4SO
J225 225 HP J225CX4SRS
J225PX4SRS
J225CX4SOC
J225CZ4SOS
J225PX4SOC
J225PZ4SOS
BJ225 225 HP BJ225CX4SDC
BJ225X4SDC
BJ225CX4SO
BJ225PX4SO

Johnson Evinrude Fitment Information

The listed J200, BJ200, J225, and BJ225 model numbers are specific 4-stroke applications. Confirm the complete engine model and required BRP OEM port-side gasket number before ordering.

Common Symptoms of a Failed Cylinder Head Gasket

A damaged head gasket may allow combustion pressure, cooling water, or engine oil to leak between internal engine passages.

Possible symptoms include:

  • Loss of cylinder compression
  • Engine overheating
  • Cooling water entering a combustion chamber
  • Water contamination in engine oil
  • Rough running or engine misfires
  • Reduced engine performance
  • Difficulty starting
  • Combustion gases entering the cooling system
  • Visible gasket damage during cylinder head removal
Diagnostic Reminder

These symptoms can also be caused by other engine problems. Perform appropriate diagnostic testing before determining that the head gasket requires replacement.

Installation and Service Tips

Cylinder head gasket replacement requires removal of the appropriate cylinder head and inspection of the engine's sealing surfaces. Follow the service manual for the exact engine model.

Recommended Installation Practices

  • Verify the engine model and serial number.
  • Confirm the port cylinder bank is being serviced.
  • Confirm the required Suzuki or BRP OEM gasket number.
  • Allow the engine to cool before disassembly.
  • Remove the cylinder head according to the service manual.
  • Inspect the cylinder head and engine block sealing surfaces.
  • Check for warpage, corrosion, cracks, and other damage.
  • Remove old gasket material without damaging the sealing surfaces.
  • Keep debris out of cylinders and internal passages.
  • Install the replacement gasket in the correct orientation.
  • Follow the manufacturer's specified tightening sequence and procedure.
  • Replace additional seals or fasteners when required by the service manual.
  • Inspect the cooling system for conditions that may have caused the original failure.
  • Check engine operation and cooling performance after reassembly.

Important Cylinder Head Installation Warning

Proper gasket installation requires correct surface preparation, cylinder head inspection, and the appropriate fastener tightening procedure.

Do not install a new head gasket over warped, cracked, or improperly prepared sealing surfaces. Improper installation can cause compression loss, cooling water leakage, overheating, and engine damage.

Key Features and Benefits

  • Port-Specific Design: Intended for the port cylinder head on compatible V6 outboards.
  • Pro Marine Aftermarket Replacement: Alternative to the listed Suzuki and BRP OEM port head gaskets.
  • Suzuki 200-250 HP Applications: Listed for select DF200, DF225, and DF250 V6 4-stroke engines.
  • Johnson Evinrude Compatibility: Listed for the specified 200 HP and 225 HP 4-stroke models.
  • Engine Repair Component: Used during compatible cylinder head repairs and engine rebuilding.
  • Combustion Chamber Sealing: Provides the gasket interface between the port cylinder head and engine block.
  • Matching Starboard Gasket Available: Pro Marine 9314 is sold separately.
  • Dealer Pricing Available: Qualified marine businesses can apply for wholesale pricing.

Frequently Asked Questions

Is Pro Marine 9324 the port or starboard head gasket?

Pro Marine 9324 is the port-side cylinder head gasket. The matching starboard gasket is Pro Marine 9314.

What Suzuki OEM numbers does Pro Marine 9324 replace?

It cross references 11142-93J00, 11142-93J01, 11142-93J02, 11142-93J03, and 11142-93J10.

What Johnson Evinrude OEM numbers does this gasket replace?

The listed BRP cross references are 5034854, 5035971, and 5036630.

What is the matching starboard head gasket?

The matching starboard gasket is Pro Marine 9314 , which cross references Suzuki OEM 11141-93J10.

Does this gasket fit Suzuki DF200 outboards?

Yes. It is listed for select Suzuki DF200 200 HP V6 4-stroke outboards, including DF200, DF200T, and DF200Z applications.

Does this gasket fit Suzuki DF225 outboards?

Yes. It is listed for select Suzuki DF225 225 HP V6 4-stroke outboards, including DF225, DF225T, and DF225Z applications.

Does this gasket fit Suzuki DF250 outboards?

Yes. It is listed for select Suzuki DF250 250 HP V6 4-stroke outboards, including DF250, DF250T, and DF250Z applications. DF250ST applications should be confirmed against the OEM diagram.

Does this gasket fit Johnson and Evinrude 200 HP and 225 HP outboards?

Yes. It is listed for the specific Johnson Evinrude 200 HP and 225 HP 4-stroke model numbers shown in the compatibility table.

Can I use the port gasket on the starboard side?

No. The port and starboard cylinder banks require their corresponding head gaskets. Pro Marine 9324 is for the port side only.

Do I need both head gaskets for a V6 engine rebuild?

If both cylinder heads are removed, each cylinder bank requires its correct replacement gasket. The port and starboard gaskets are sold separately.

Is Pro Marine 9324 a genuine Suzuki OEM gasket?

No. Pro Marine 9324 is an aftermarket replacement for the listed Suzuki and Johnson Evinrude OEM part numbers.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies genuine OEM and aftermarket marine engine parts, cylinder head gaskets, internal engine components, rebuild parts, and maintenance products to marine repair shops, dealerships, technicians, and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on orders over $100 within the continental United States.
  • In-stock orders received before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options available through UPS, USPS, and FedEx.
  • Typical delivery time is 1-5 business days.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused, and in original packaging.
  • Installed parts are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Confirming Head Gasket Fitment?

If you are unsure whether Pro Marine 9324 is the correct port cylinder head gasket for your Suzuki, Johnson, or Evinrude outboard, contact Pro Marine with your engine model and serial number.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

9324, 11142-93J00, 11142-93J01, 11142-93J02, 11142-93J03, 11142-93J10, 1114293J00, 1114293J01, 1114293J02, 1114293J03, 1114293J10, 5034854, 5035971, 5036630

Searchable Terms

Pro Marine 9324, Suzuki 11142-93J00, Suzuki 11142-93J01, Suzuki 11142-93J02, Suzuki 11142-93J03, Suzuki 11142-93J10, Johnson Evinrude 5034854, Johnson Evinrude 5035971, Johnson Evinrude 5036630, Suzuki port head gasket, Suzuki PORT head gasket, Suzuki left cylinder head gasket, Suzuki V6 cylinder head gasket, Suzuki DF200 port head gasket, Suzuki DF200T port head gasket, Suzuki DF200Z port head gasket, Suzuki DF225 port head gasket, Suzuki DF225T port head gasket, Suzuki DF225Z port head gasket, Suzuki DF250 port head gasket, Suzuki DF250T port head gasket, Suzuki DF250Z port head gasket, Suzuki 200HP head gasket, Suzuki 225HP head gasket, Suzuki 250HP head gasket, Suzuki 200-250 HP head gasket, Suzuki 4 stroke port head gasket, Suzuki outboard cylinder head gasket, Johnson 200HP port head gasket, Johnson 225HP port head gasket, Evinrude 200HP port head gasket, Evinrude 225HP port head gasket, Johnson Evinrude V6 head gasket, BRP port head gasket, J200CX4SRS head gasket, J200PX4SRS head gasket, J225CX4SRS head gasket, J225PX4SRS head gasket, BJ200CX4SDC head gasket, BJ200X4SDC head gasket, BJ225CX4SDC head gasket, BJ225X4SDC head gasket, BJ200CX4SO head gasket, BJ200PX4SO head gasket, BJ225CX4SO head gasket, BJ225PX4SO head gasket, J200CX4SOC head gasket, J200PX4SOC head gasket, J225CX4SOC head gasket, J225CZ4SOS head gasket, J225PX4SOC head gasket, J225PZ4SOS head gasket, Suzuki V6 engine rebuild, Suzuki cylinder head repair, Suzuki outboard engine repair, aftermarket Suzuki head gasket, Pro Marine Suzuki engine parts, Pro Marine 9314 matching starboard gasket

Item#:
9324
Cross Reference#:
11142-93J00
11142-93J01
11142-93J02
11142-93J03
11142-93J10
5034854
5035971
5036630
Manufacturer Item:
11142-93J10
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
65.91
Each
Starboard Side 200-250 HP 2004-2025 and Johnson Evinrude 200-225 HP

Pro Marine Aftermarket Suzuki and Johnson Evinrude V6 Engine Components

Pro Marine Starboard Cylinder Head Gasket for Suzuki DF200 DF225 DF250 V6 4-Stroke Outboards

The Pro Marine 9314 Starboard Cylinder Head Gasket is an aftermarket replacement for the starboard (STBD) cylinder head on select Suzuki DF200, DF225, and DF250 200-250 HP V6 4-stroke outboard engines.

This gasket also fits the specified Johnson and Evinrude 200 HP and 225 HP 4-stroke V6 outboards listed in the compatibility tables below.

Pro Marine 9314 cross references Suzuki OEM 11141-93J00, 11141-93J01, 11141-93J02, 11141-93J03, and 11141-93J10, along with BRP OEM 5034853, 5035938, and 5036629.

The gasket seals the starboard cylinder head to the engine block, helping maintain combustion chamber compression while separating cooling water and engine lubrication passages.

Important: This is the STARBOARD SIDE ONLY. The matching port-side cylinder head gasket is sold separately as Pro Marine 9324 .

Important: Starboard and Port Head Gaskets Are Different

Suzuki DF200, DF225, and DF250 V6 engines use separate cylinder head gaskets for the starboard and port cylinder banks.

  • Starboard Side (STBD): Pro Marine 9314 - Suzuki OEM 11141-93J10
  • Port Side (PORT): Pro Marine 9324 - Suzuki OEM 11142-93J10

These gaskets are not interchangeable. Confirm which cylinder bank is being serviced before ordering.

Product Information

  • Pro Marine Part Number: 9314
  • Brand: Pro Marine Aftermarket
  • Product Type: Cylinder Head Gasket
  • Cylinder Bank: Starboard (STBD)
  • Primary Suzuki OEM Reference: 11141-93J10
  • Additional Suzuki OEM References: 11141-93J00, 11141-93J01, 11141-93J02, 11141-93J03
  • Johnson Evinrude BRP References: 5034853, 5035938, 5036629
  • Engine Manufacturers: Suzuki, Johnson, Evinrude
  • Engine Type: V6 4-Stroke Outboard
  • Suzuki Horsepower: 200 HP, 225 HP, 250 HP
  • Johnson Evinrude Horsepower: 200 HP, 225 HP
  • Suzuki Engine Families: DF200, DF225, DF250
  • Additional Suzuki Models: DF200T, DF200Z, DF225T, DF225Z, DF250T, DF250Z and listed DF250ST configurations
  • Earlier Suzuki Applications: 2004-2010
  • Additional Suzuki Catalog Listings: 2013, 2015, and specified later model variants
  • Matching Port Gasket: Pro Marine 9324
  • Condition: New

Matching Port Side Cylinder Head Gasket Available

Servicing both cylinder heads on your Suzuki DF200, DF225, or DF250 V6 outboard? The matching port-side gasket is available separately from Pro Marine USA.

Pro Marine 9324 - PORT Cylinder Head Gasket

Matching aftermarket port-side cylinder head gasket for select Suzuki DF200, DF225, and DF250 V6 4-stroke outboards.

Suzuki OEM: 11142-93J10
Location: Port Cylinder Bank
Sold Separately

View Matching Port Head Gasket

Verify both gasket part numbers against your engine model and serial number. The starboard and port gaskets are purchased individually.

OEM and Cross Reference Numbers

Pro Marine 9314 replaces the following Suzuki and Johnson Evinrude starboard cylinder head gasket numbers.

Manufacturer Part Number Description
Pro Marine 9314 Aftermarket Starboard Head Gasket
Suzuki OEM 11141-93J00 STBD Cylinder Head Gasket Reference
Suzuki OEM 11141-93J01 STBD Cylinder Head Gasket Reference
Suzuki OEM 11141-93J02 STBD Cylinder Head Gasket Reference
Suzuki OEM 11141-93J03 STBD Cylinder Head Gasket Reference
Suzuki OEM 11141-93J10 STBD Cylinder Head Gasket Reference
Johnson Evinrude BRP 5034853 Starboard Head Gasket Cross Reference
Johnson Evinrude BRP 5035938 Starboard Head Gasket Cross Reference
Johnson Evinrude BRP 5036629 Starboard Head Gasket Cross Reference

What This Part Is Used For

The starboard cylinder head gasket seals the connection between the starboard cylinder head and engine block on compatible Suzuki and Johnson Evinrude V6 outboards.

It helps maintain combustion chamber compression and separates the cooling water and engine oil passages at the cylinder head sealing surface.

This gasket is used during repairs involving the starboard cylinder head, including head gasket replacement, cylinder head service, and compatible V6 engine rebuilding.

Common Repair Applications

  • Suzuki DF200 V6 starboard cylinder head repairs
  • Suzuki DF225 V6 starboard cylinder head repairs
  • Suzuki DF250 V6 starboard cylinder head repairs
  • Johnson 200 HP and 225 HP 4-stroke V6 repairs
  • Evinrude 200 HP and 225 HP 4-stroke V6 repairs
  • Replacement of a leaking or damaged starboard head gasket
  • Engine repairs requiring starboard cylinder head removal
  • Compatible V6 outboard engine rebuilding

Important Fitment Note

Pro Marine 9314 is a starboard-side cylinder head gasket for select Suzuki DF200, DF225, and DF250 V6 4-stroke outboards.

The supplied fitment includes earlier 2004-2010 Suzuki applications, additional 2013 and 2015 catalog listings, and specific later model variations identified by model suffixes and serial references.

Some DF250ST and other specialized DF250 configurations may use different cylinder head gaskets. Confirm OEM 11141-93J10 or another listed 11141-93J reference in the engine's specific parts diagram.

Do not order by horsepower alone. Verify the engine model, serial number, cylinder bank, and OEM gasket number.

Compatible Suzuki Outboard Applications

Pro Marine 9314 is listed for select Suzuki DF200, DF225, and DF250 200-250 HP V6 4-stroke outboards.

The following tables group the supplied engine fitment into readable model families while retaining the listed serial and catalog identifiers.

Suzuki DF200 - 200 HP V6 4-Stroke

Engine Model Listed Applications Serial References
DF200 2004-2010
2013 and 2015 listings
Additional serial-specific applications
-51001
20002F-210001
20002F-310001
20002Z-210001
20002Z-310001
22503F-210001
22503F-310001
22503Z-210001
22503Z-310001
25003F-210001
25003F-310001
25003Z-210001
25003Z-310001
25004F-210001
25004F-310001
710001
DF200T 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial reference
20002F-440001
20002F-540001
20002F-640001
DF200Z 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial reference
20002Z-440001
20002Z-540001
20002Z-640001

Suzuki DF225 - 225 HP V6 4-Stroke

Engine Model Listed Applications Serial References
DF225 2004-2010
2013 and 2015 listings
Additional serial-specific applications
-51001
20002F-210001
20002F-310001
20002Z-210001
20002Z-310001
22503F-210001
22503F-310001
22503Z-210001
22503Z-310001
25003F-210001
25003F-310001
25003Z-210001
25003Z-310001
25004F-210001
25004F-310001
710001
DF225T 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
22503F-040001
22503F-440001
22503F-540001
22503F-640001
DF225Z 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
22503Z-040001
22503Z-440001
22503Z-540001
22503Z-640001

Suzuki DF250 - 250 HP V6 4-Stroke

Engine Model Listed Applications Serial References
DF250 2004-2010
2013 and 2015 listings
Additional serial-specific applications
-51001
20002F-210001
20002F-310001
20002Z-210001
20002Z-310001
22503F-210001
22503F-310001
22503Z-210001
22503Z-310001
25003F-210001
25003F-310001
25003Z-210001
25003Z-310001
25004F-210001
25004F-310001
710001
DF250T 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
25003F-040001
25003F-440001
25003F-540001
25003F-640001
DF250Z 2004-2007
Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
25003Z-040001
25003Z-440001
25003Z-540001
25003Z-640001
DF250ST Catalog variants 020, 021, 022, 024, 025
Additional listed serial references
OEM verification required
25004F-040001
25004F-440001
25004F-540001
25004F-640001
DF250ST Fitment Warning

DF250ST applications appear in the supplied catalog fitment, but certain DF250S/SS configurations use a different starboard head gasket, Suzuki OEM 11141-98J10. Verify the exact OEM gasket number before purchasing Pro Marine 9314.

Additional Suzuki Catalog Model Identifiers

The supplied fitment includes the following model-specific catalog identifiers:

  • DF200T: 020, 021, 022, 024, 025
  • DF200Z: 020, 021, 022, 024, 025
  • DF225T: 020, 021, 022, 024, 025
  • DF225Z: 020, 021, 022, 024, 025
  • DF250T: 020, 021, 022, 024, 025
  • DF250Z: 020, 021, 022, 024, 025
  • DF250ST: 020, 021, 022, 024, 025 - verify OEM gasket number

These identifiers help distinguish catalog applications. They do not establish compatibility with every engine in a horsepower family.

Compatible Johnson and Evinrude Outboard Applications

Pro Marine 9314 also cross references BRP starboard head gasket numbers 5034853, 5035938, and 5036629.

The following Johnson Evinrude 200 HP and 225 HP 4-stroke models are included in the supplied fitment.

Engine Family Horsepower Compatible Model Numbers
J200 200 HP J200CX4SRS
J200PX4SRS
J200CX4SOC
J200PX4SOC
BJ200 200 HP BJ200CX4SDC
BJ200X4SDC
BJ200CX4SO
BJ200PX4SO
J225 225 HP J225CX4SRS
J225PX4SRS
J225CX4SOC
J225CZ4SOS
J225PX4SOC
J225PZ4SOS
BJ225 225 HP BJ225CX4SDC
BJ225X4SDC
BJ225CX4SO
BJ225PX4SO

Johnson Evinrude Fitment Information

The listed J200, BJ200, J225, and BJ225 models are specific Johnson Evinrude 4-stroke applications.

Confirm the complete engine model and the required BRP OEM starboard head gasket number before ordering.

Common Symptoms of a Failed Cylinder Head Gasket

A damaged head gasket can allow combustion pressure, cooling water, or engine oil to leak between internal engine passages.

Possible symptoms include:

  • Loss of cylinder compression
  • Engine overheating
  • Cooling water entering a combustion chamber
  • Water contamination in engine oil
  • Rough running or engine misfires
  • Reduced engine performance
  • Difficulty starting
  • Combustion gases entering the cooling system
  • Visible gasket damage during cylinder head removal
Diagnostic Reminder

These symptoms can also be caused by other engine problems. Perform appropriate diagnostic testing before determining that the head gasket requires replacement.

Installation and Service Tips

Cylinder head gasket replacement requires removal of the appropriate cylinder head and inspection of the engine's sealing surfaces. Follow the service manual for the exact engine model.

Recommended Installation Practices

  • Verify the engine model and serial number.
  • Confirm the starboard cylinder bank is being serviced.
  • Confirm the required Suzuki or BRP OEM gasket number.
  • Allow the engine to cool before disassembly.
  • Remove the cylinder head according to the service manual.
  • Inspect the cylinder head and engine block sealing surfaces.
  • Check for warpage, corrosion, cracks, and other damage.
  • Remove old gasket material without damaging the sealing surfaces.
  • Keep debris out of the cylinders and internal passages.
  • Install the replacement gasket in the correct orientation.
  • Follow the manufacturer's specified tightening sequence and procedure.
  • Replace additional seals or fasteners when required by the service manual.
  • Inspect the cooling system for conditions that may have caused the original failure.
  • Check engine operation and cooling performance after reassembly.

Important Cylinder Head Installation Warning

Proper gasket installation requires correct surface preparation, cylinder head inspection, and the appropriate fastener tightening procedure.

Do not install a new head gasket over warped, cracked, or improperly prepared sealing surfaces. Improper installation can cause compression loss, cooling water leakage, overheating, and engine damage.

Key Features and Benefits

  • Starboard-Specific Design: Intended for the starboard cylinder head on compatible V6 outboards.
  • Pro Marine Aftermarket Replacement: Alternative to the listed Suzuki and BRP OEM starboard head gaskets.
  • Suzuki 200-250 HP Applications: Listed for select DF200, DF225, and DF250 V6 4-stroke engines.
  • Johnson Evinrude Compatibility: Listed for the specified 200 HP and 225 HP 4-stroke models.
  • Engine Repair Component: Used during compatible cylinder head repairs and engine rebuilding.
  • Combustion Chamber Sealing: Provides the gasket interface between the starboard cylinder head and engine block.
  • Matching Port Gasket Available: Pro Marine 9324 is sold separately.
  • Dealer Pricing Available: Qualified marine businesses can apply for wholesale pricing.

Frequently Asked Questions

What Suzuki OEM numbers does Pro Marine 9314 replace?

Pro Marine 9314 cross references 11141-93J00, 11141-93J01, 11141-93J02, 11141-93J03, and 11141-93J10.

What Johnson Evinrude OEM numbers does this gasket replace?

The listed BRP cross references are 5034853, 5035938, and 5036629.

Is Pro Marine 9314 the starboard or port head gasket?

Pro Marine 9314 is the starboard (STBD) cylinder head gasket. It is not the port-side gasket.

What is the matching port-side head gasket?

The matching port-side gasket is Pro Marine 9324 , which cross references Suzuki OEM 11142-93J10.

Does this gasket fit Suzuki DF200 outboards?

Yes. It is listed for select Suzuki DF200 200 HP V6 4-stroke outboards, including DF200, DF200T, and DF200Z applications.

Does this gasket fit Suzuki DF225 outboards?

Yes. It is listed for select Suzuki DF225 225 HP V6 4-stroke outboards, including DF225, DF225T, and DF225Z applications.

Does this gasket fit Suzuki DF250 outboards?

Yes. It is listed for select Suzuki DF250 250 HP V6 4-stroke outboards, including DF250, DF250T, and DF250Z applications. DF250ST applications require additional OEM verification.

Does this gasket fit Johnson and Evinrude 200 HP and 225 HP outboards?

Yes. It is listed for the specific Johnson Evinrude 200 HP and 225 HP 4-stroke model numbers shown in the compatibility table.

Are the starboard and port head gaskets interchangeable?

No. The starboard and port cylinder banks use different head gaskets. Pro Marine 9314 is for the starboard side, while Pro Marine 9324 is for the port side.

Do I need both head gaskets for a V6 engine rebuild?

If both cylinder heads are removed during an engine rebuild, each cylinder bank requires its correct replacement gasket. The starboard and port gaskets are sold separately.

What are common symptoms of a blown head gasket?

Possible symptoms include compression loss, overheating, rough running, water intrusion, and engine oil contamination. Proper diagnostic testing is required to confirm the cause.

Is Pro Marine 9314 a genuine Suzuki OEM gasket?

No. Pro Marine 9314 is an aftermarket replacement for the listed Suzuki and Johnson Evinrude OEM part numbers.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies genuine OEM and aftermarket marine engine parts, cylinder head gaskets, internal engine components, rebuild parts, and maintenance products to marine repair shops, dealerships, technicians, and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible products.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on orders over $100 within the continental United States.
  • In-stock orders received before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options available through UPS, USPS, and FedEx.
  • Typical delivery time is 1-5 business days.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused, and in original packaging.
  • Installed parts are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Confirming Head Gasket Fitment?

If you are unsure whether Pro Marine 9314 is the correct starboard cylinder head gasket for your Suzuki, Johnson, or Evinrude outboard, contact Pro Marine with your engine model and serial number.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

9314, 11141-93J00, 11141-93J01, 11141-93J02, 11141-93J03, 11141-93J10, 1114193J00, 1114193J01, 1114193J02, 1114193J03, 1114193J10, 5034853, 5035938, 5036629

Searchable Terms

Pro Marine 9314, Suzuki 11141-93J00, Suzuki 11141-93J01, Suzuki 11141-93J02, Suzuki 11141-93J03, Suzuki 11141-93J10, Johnson Evinrude 5034853, Johnson Evinrude 5035938, Johnson Evinrude 5036629, Suzuki starboard head gasket, Suzuki STBD head gasket, Suzuki right cylinder head gasket, Suzuki V6 cylinder head gasket, Suzuki DF200 head gasket, Suzuki DF200T head gasket, Suzuki DF200Z head gasket, Suzuki DF225 head gasket, Suzuki DF225T head gasket, Suzuki DF225Z head gasket, Suzuki DF250 head gasket, Suzuki DF250T head gasket, Suzuki DF250Z head gasket, Suzuki 200HP head gasket, Suzuki 225HP head gasket, Suzuki 250HP head gasket, Suzuki 200-250 HP head gasket, Suzuki 4 stroke head gasket, Suzuki outboard cylinder head gasket, Johnson 200HP head gasket, Johnson 225HP head gasket, Evinrude 200HP head gasket, Evinrude 225HP head gasket, Johnson Evinrude V6 head gasket, BRP starboard head gasket, J200CX4SRS head gasket, J200PX4SRS head gasket, J225CX4SRS head gasket, J225PX4SRS head gasket, BJ200CX4SDC head gasket, BJ200X4SDC head gasket, BJ225CX4SDC head gasket, BJ225X4SDC head gasket, BJ200CX4SO head gasket, BJ200PX4SO head gasket, BJ225CX4SO head gasket, BJ225PX4SO head gasket, J200CX4SOC head gasket, J200PX4SOC head gasket, J225CX4SOC head gasket, J225CZ4SOS head gasket, J225PX4SOC head gasket, J225PZ4SOS head gasket, Suzuki outboard engine rebuild, Suzuki V6 engine repair, Suzuki cylinder head repair, aftermarket Suzuki head gasket, Pro Marine Suzuki engine parts, Pro Marine 9324 matching port gasket

Item#:
9314
Cross Reference#:
11141-93J00
11141-93J01
11141-93J02
11141-93J02
11141-93J03
11141-93J10
5034853
5035938
5036629
Manufacturer Item:
11141-93J10
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
70.56
Each
Suzuki DF200-DF300HP 2004-2010 Johnson Evinrude 200-225
Item#:
9311
Cross Reference#:
15410-93J00
15410-93J01
5034984
Manufacturer Item:
15410-93J01
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
46.35
Each
Aftermarket Replacement for 15410-87J10 and 5030702 - 25-140 HP

Pro Marine Aftermarket Fuel System Components

Pro Marine 7716P Fuel Filter - Suzuki DF25-DF140 and Johnson/Evinrude Four-Stroke Outboards

The Pro Marine 7716P Fuel Filter is an aftermarket replacement fuel filter for select Suzuki DF25, DF30, DF40, DF50, DF60, DF70, DF90, DF100, DF115 and DF140 four-stroke outboard engines. It also fits specified Johnson and Evinrude 25-140 HP four-stroke outboards.

Designed to replace the specified original equipment fuel filters, Pro Marine 7716P helps remove contaminants from the engine's fuel supply before they reach downstream fuel system components.

This Pro Marine aftermarket filter cross references Suzuki OEM 15410-87J10 and 15410-60C00, along with Johnson/Evinrude 5030702, 5032323, 0765573 and 765573. It also cross references Sierra 18-7716.

Whether performing scheduled maintenance, replacing a restricted fuel filter, or servicing an older Suzuki-based Johnson/Evinrude outboard, Pro Marine 7716P provides an aftermarket replacement option for the specific engines listed below.

Product Information

  • Part Number: 7716P
  • Brand: Pro Marine
  • Product Type: Aftermarket Fuel Filter
  • Suzuki OEM References: 15410-60C00, 15410-87J10
  • Johnson/Evinrude References: 5030702, 5032323, 0765573, 765573
  • Sierra Cross Reference: 18-7716
  • Engine Type: Four-Stroke Outboard
  • Suzuki Applications: Select DF25 through DF140 Models
  • Johnson/Evinrude Applications: Select 25 through 140 HP Four-Stroke Models
  • Application: Engine Fuel System Filtration

OEM and Cross Reference Numbers

Pro Marine 7716P is an aftermarket replacement associated with the following OEM and aftermarket fuel filter references.

Manufacturer Part Number Reference
Pro Marine 7716P Aftermarket Fuel Filter
Suzuki Marine 15410-60C00 OEM Cross Reference
Suzuki Marine 15410-87J10 OEM Cross Reference
Johnson / Evinrude 5030702 OEM Cross Reference
Johnson / Evinrude 5032323 OEM Cross Reference
Johnson / Evinrude 0765573 OEM Reference
Johnson / Evinrude 765573 Reference Without Leading Zero
Sierra Marine 18-7716 Aftermarket Cross Reference

OEM part numbers are provided for identification and cross-reference purposes. This product is a Pro Marine aftermarket replacement, not a Genuine Suzuki or Johnson/Evinrude OEM part.

What This Part Is Used For

The engine fuel filter helps remove dirt, debris and other contaminants from fuel before they travel through downstream fuel system components.

Over time, accumulated contamination can restrict fuel flow. Replacing a restricted filter may help restore normal fuel delivery when the filter is responsible for the restriction.

Common Service Applications

  • Routine Suzuki four-stroke outboard maintenance
  • Johnson and Evinrude four-stroke engine servicing
  • Replacement of contaminated or restricted fuel filters
  • Fuel system troubleshooting
  • Preventive maintenance during scheduled service
  • Fuel system repairs following contamination
  • Marine dealership and repair shop service work

Important Fitment Information

This filter does not fit every Suzuki or Johnson/Evinrude engine between 25 and 140 HP.

The compatibility information below identifies specific Suzuki engine generations, production years and model variations. Johnson/Evinrude applications are identified by their model numbers, with production years and rigging details included where supplied.

Always confirm the original fuel filter part number using the complete engine model and applicable OEM parts diagram.

Compatible Suzuki Outboard Applications

The following applications are based on the specified Suzuki four-stroke outboard models. Individual production years have been combined into readable ranges without extending fitment beyond the supplied model information.

Horsepower Suzuki Model Production Years
25 HP DF25 2000-2005
25 HP DF25Q 2000-2007
25 HP DF25Q(QR) 2000-2007
25 HP DF25T 2000-2007
30 HP DF30 2000-2006
30 HP DF30Q 2000-2007
30 HP DF30Q(QR) 2000-2007
30 HP DF30T 2000-2007
40 HP DF40 1999-2010
40 HP DF40QH 1999-2007
40 HP DF40TL 1999-2007
50 HP DF50 1999-2010
50 HP DF50QH 1999-2007
50 HP DF50TL 1999-2007
60 HP DF60 1998-2009
60 HP DF60HL 1998-2007
60 HP DF60TL 1998-2007
70 HP DF70 1998-2009
70 HP DF70THL 1998-2007
70 HP DF70TL 1998-2007
90 HP DF90 2001-2008
90 HP DF90TL 2001-2007
100 HP DF100 2009-2010
115 HP DF115 2001-2010
115 HP DF115TL 2001-2007
140 HP DF140 2002-2010
140 HP DF140T 2002-2010
140 HP DF140Z 2002-2010

Compatible Johnson and Evinrude Four-Stroke Applications

Pro Marine 7716P is also listed for the following Johnson and Evinrude four-stroke outboards. These applications include specific early Evinrude models and later Suzuki-based Johnson/Evinrude model designations.

Early Evinrude and Johnson Four-Stroke Applications

Brand Model Year
Evinrude E40PL4EES 1999
Evinrude E50PL4EES 1999
Evinrude E70FTLECS 1998
Evinrude E70PL4EEC 1999
Johnson J70FLTLECS 1998

Evinrude 25-30 HP Four-Stroke - 2000-2001

HP Model Year Configuration
25 E25EL4SIC / E25EL4SSS 2001 / 2000 Electric Start, 20-inch Shaft
25 E25PL4SIC / E25PL4SSS 2001 / 2000 Electric Start, Power Trim and Tilt, 15-inch Shaft
25 E25R4SIC / E25R4SSS 2001 / 2000 Rope Start, Tiller, 15-inch Shaft
25 E25RL4SIC / E25RL4SSS 2001 / 2000 Rope Start, Tiller, 20-inch Shaft
25 E25TE4SIC / E25TE4SSS 2001 / 2000 Electric Start, Tiller, 15-inch Shaft
25 E25TEL4SIC / E25TEL4SSS 2001 / 2000 Electric Start, Tiller, 20-inch Shaft
30 E30EL4SIC / E30EL4SSS 2001 / 2000 Electric Start, 20-inch Shaft
30 E30PL4SIC / E30PL4SSS 2001 / 2000 Electric Start, Power Trim and Tilt, 20-inch Shaft
30 E30R4SIC / E30R4SSS 2001 / 2000 Rope Start, Tiller, 15-inch Shaft
30 E30RL4SIC / E30RL4SSS 2001 / 2000 Rope Start, Tiller, 20-inch Shaft
30 E30TE4SIC / E30TE4SSS 2001 / 2000 Electric Start, Tiller, 15-inch Shaft
30 E30TEL4SIC / E30TEL4SSS 2001 / 2000 Electric Start, Tiller, 20-inch Shaft

Evinrude 40-70 HP Four-Stroke - 2000-2001

HP Model Year Configuration
40 E40PL4SSC 2000 Electric Start, Power Trim and Tilt, 20-inch Shaft
40 E40PL4SIR 2001 Electric Start, Power Trim and Tilt, 20-inch Shaft
50 E50PL4SSC 2000 Electric Start, Power Trim and Tilt, 20-inch Shaft
50 E50PL4SIR 2001 Electric Start, Power Trim and Tilt, 20-inch Shaft
70 E70 PL4SSR 2000 Electric Start, Power Trim and Tilt, 20-inch Shaft
70 E70PL4SIA 2001 Electric Start, Power Trim and Tilt, Blue, 20-inch Shaft

Johnson 25-30 HP Four-Stroke Models

Horsepower Compatible Model Numbers
25 HP J25PL4SOC
J25PL4SRS
J25TEL4SRS
J25TEL4SOC
30 HP J30PL4SDR
J30PL4SOC
J30PL4SRS
J30PL4SUA
J30TEL4SDR
J30TEL4SOC
J30TEL4SRS
J30TEL4SUA

Johnson 40-50 HP Four-Stroke Models

Horsepower Compatible Model Numbers
40 HP J40PL4SDE
J40PL4SNF (2002)
J40PL4SOB
J40PL4SRM
J40PL4STC
BJ40PL4SDR
BJ40PL4SOC
BJ40PL4SRS
50 HP J50PL4SDE
J50PL4SNF (2002)
J50PL4SOB
J50PL4SRM
J50PL4STC
BJ50PL4SDR
BJ50PL4SOC
BJ50PL4SRS

Johnson 60-70 HP Four-Stroke Models

Horsepower Compatible Model Numbers
60 HP J60PL4SDM
J60PL4SNF (2002)
J60PL4SRR
J60PL4STC
BJ60PL4SDM
BJ60PL4SRR
BJ60PL4STC
70 HP J70PL4SDM
J70PL4SNF (2002)
J70PL4SRR
J70PL4STC
BJ70PL4SDM
BJ70PL4SRR
BJ70PL4STC

Johnson 90 HP Four-Stroke Models

Model Family Compatible Model Numbers
J90PL4 J90PL4SDA
J90PL4SRC
J90PL4STS
J90PX4 J90PX4SDA
J90PX4SRC
J90PX4STS
BJ90PL4 BJ90PL4SDA
BJ90PL4SRC
BJ90PL4STS
BJ90PX4 BJ90PX4SDA
BJ90PX4SRC
BJ90PX4STS

Johnson 115 HP Four-Stroke Models

Model Family Compatible Model Numbers
J115PL4 J115PL4SDA
J115PL4SRC
J115PL4STS
J115PX4 J115PX4SDA
J115PX4SRC
J115PX4STS
BJ115L4 BJ115L4SRC
BJ115L4STS
BJ115PL4 BJ115PL4SDA
BJ115PX4 BJ115PX4SDA
BJ115X4 BJ115X4SRC
BJ115X4STS

Johnson 140 HP Four-Stroke Models

Model Family Compatible Model Numbers
J140CX4 J140CX4SDA
J140CX4SRC
J140CX4STS
J140PL4 J140PL4SDA
J140PL4SRC
J140PL4STS
J140PX4 J140PX4SDA
J140PX4SRS
J140PX4STS
BJ140CX4 BJ140CX4DR
BJ140CX4SRS
BJ140L4 BJ140L4SDR
BJ140PL4 BJ140PL4SRS
BJ140PX4 BJ140PX4SRS
BJ140X4 BJ140X4SDR
Johnson and Evinrude Compatibility Note

These applications are specific four-stroke engine model designations. The presence of a horsepower rating in this table does not establish compatibility with every Johnson or Evinrude engine of that horsepower.

Common Symptoms of a Restricted Fuel Filter

A restricted or contaminated fuel filter may reduce fuel delivery to the engine. Depending on operating conditions and the severity of the restriction, symptoms may include:

  • Hesitation during acceleration
  • Reduced engine performance at higher RPM
  • Difficulty maintaining RPM under load
  • Hard starting associated with insufficient fuel delivery
  • Engine stalling or inconsistent operation
  • Visible debris or contamination in the fuel system
  • Reduced fuel flow through a restricted filter

These symptoms can have other causes. Diagnose the fuel system before replacing components.

Installation and Service Tips

Follow the appropriate Suzuki or Johnson/Evinrude factory service manual when replacing fuel filtration components.

  • Confirm the correct replacement filter using the OEM part number.
  • Turn off the engine before opening the fuel system.
  • Keep ignition sources away from the work area.
  • Relieve fuel system pressure where required.
  • Prevent dirt and debris from entering open fuel connections.
  • Inspect the filter housing and associated sealing components.
  • Install the replacement filter according to the service manual.
  • Replace associated seals when required.
  • Prime the fuel system as instructed by the manufacturer.
  • Inspect carefully for leaks before operating the engine.

Fuel System Safety Warning

Gasoline is highly flammable. Do not service fuel system components near open flames, sparks or other ignition sources. Follow the manufacturer's fuel system safety procedures.

Key Features and Benefits

  • Pro Marine Aftermarket Replacement: An alternative to the original equipment fuel filter for the specified applications.
  • Fuel System Filtration: Helps remove contaminants from fuel before they reach downstream components.
  • Suzuki Compatibility: Fits the specified Suzuki DF25 through DF140 four-stroke engine models.
  • Johnson/Evinrude Compatibility: Covers the listed 25 through 140 HP four-stroke engine model designations.
  • Multiple Cross References: Associated with Suzuki 15410-60C00, 15410-87J10, Johnson/Evinrude 5030702, 5032323, 0765573, 765573 and Sierra 18-7716.
  • Maintenance and Repair: Suitable for routine fuel filter replacement where this part is specified.

Frequently Asked Questions

Is Pro Marine 7716P a Genuine Suzuki fuel filter?

No. Pro Marine 7716P is an aftermarket replacement fuel filter for the specified Suzuki and Johnson/Evinrude four-stroke applications.

What Suzuki OEM numbers does 7716P replace?

The supplied Suzuki cross references are 15410-60C00 and 15410-87J10.

What Johnson/Evinrude numbers cross reference 7716P?

The supplied references include 5030702, 5032323, 0765573 and 765573.

What Sierra filter cross references Pro Marine 7716P?

The Sierra cross reference is 18-7716.

Does 7716P fit Suzuki DF25 and DF30 outboards?

Yes. It is listed for the specified DF25 and DF30 models and Q, QR and T variations from 2000-2007, depending on the exact model designation.

Does this filter fit Suzuki DF40 and DF50?

Yes. It is listed for DF40 and DF50 models from 1999-2010 and the specified QH and TL variations from 1999-2007.

Does it fit Suzuki DF60 and DF70?

Yes. It is listed for DF60 and DF70 models from 1998-2009 and the specified HL, THL and TL variations.

Does it fit Suzuki DF90?

Yes. The supplied applications include DF90 models from 2001-2008 and DF90TL models from 2001-2007.

Does it fit Suzuki DF100 and DF115?

Yes. It is listed for DF100 models from 2009-2010 and DF115 models from 2001-2010, along with DF115TL models from 2001-2007.

Does Pro Marine 7716P fit Suzuki DF140?

Yes. The supplied applications include DF140, DF140T and DF140Z models from 2002-2010.

Does it fit Evinrude 25 and 30 HP four-strokes?

Yes. The supplied applications include specific Evinrude 25 and 30 HP four-stroke models from 2000-2001.

Does this filter fit Johnson 40, 50, 60 and 70 HP engines?

Yes. It is listed for the specific Johnson four-stroke model numbers shown in the compatibility tables.

Does it fit Johnson 90, 115 and 140 HP four-strokes?

Yes. It fits the specified Suzuki-based Johnson four-stroke model designations listed above.

Does 7716P fit every Suzuki engine from 25-140 HP?

No. Compatibility is limited to the listed engine models and years. Different engine generations may use different fuel filtration components.

How do I verify the correct filter before ordering?

Use the complete engine model and identification information to locate the original filter in the applicable OEM parts diagram. Confirm the OEM part number before ordering.

Dealer Discounts & Store Policies

Wholesale Marine Parts Pricing

Pro Marine USA supplies Pro Marine aftermarket parts along with Genuine Mercury, Yamaha, Suzuki, BRP and Tohatsu marine engine parts for professional marine repair shops, dealerships, technicians and retail customers.

Qualified marine businesses can apply for a Pro Marine dealer account to access wholesale pricing on eligible parts.

Apply for Dealer Pricing

Shipping Information

  • Free shipping on qualifying orders over $100 within the continental United States. Oil and oversized items are excluded.
  • In-stock orders placed before 5:30 PM EST ship the same business day, Monday-Friday.
  • Shipping options are available through UPS, USPS and FedEx.
  • Typical delivery time is 1-5 business days, depending on destination and shipping service.

30-Day Return Policy

  • Eligible returns are accepted within 30 days.
  • Parts must be new, unused and in original packaging.
  • Installed parts are not returnable.
  • OEM electrical items are not returnable.
  • Return authorization is required before returning merchandise.

Need Help Confirming Fitment?

If you are unsure whether Pro Marine 7716P is correct for your Suzuki or Johnson/Evinrude outboard, contact Pro Marine USA with the complete engine model and identification information.

Contact Pro Marine USA or call 941-721-3000.

Searchable Part Numbers

7716P, 7716, 18-7716, 15410-60C00, 1541060C00, 15410-87J10, 1541087J10, 5030702, 5032323, 0765573, 765573

Searchable Terms

Pro Marine 7716P, Pro Marine fuel filter, Pro Marine Suzuki fuel filter, Pro Marine aftermarket fuel filter, Suzuki 15410-60C00 replacement, Suzuki 15410-87J10 replacement, Suzuki DF25 fuel filter, Suzuki DF25Q, Suzuki DF25T, Suzuki DF30 fuel filter, Suzuki DF30Q, Suzuki DF30T, Suzuki DF40 fuel filter, Suzuki DF40QH, Suzuki DF40TL, Suzuki DF50 fuel filter, Suzuki DF50QH, Suzuki DF50TL, Suzuki DF60 fuel filter, Suzuki DF60HL, Suzuki DF60TL, Suzuki DF70 fuel filter, Suzuki DF70THL, Suzuki DF70TL, Suzuki DF90 fuel filter, Suzuki DF90TL, Suzuki DF100 fuel filter, Suzuki DF115 fuel filter, Suzuki DF115TL, Suzuki DF140 fuel filter, Suzuki DF140T, Suzuki DF140Z, Johnson 5030702, Johnson 5032323, Johnson 0765573, Johnson 765573, Johnson four-stroke fuel filter, Evinrude four-stroke fuel filter, Evinrude 25 HP fuel filter, Evinrude 30 HP fuel filter, Evinrude 40 HP fuel filter, Evinrude 50 HP fuel filter, Evinrude 70 HP fuel filter, Johnson 25 HP fuel filter, Johnson 30 HP fuel filter, Johnson 40 HP fuel filter, Johnson 50 HP fuel filter, Johnson 60 HP fuel filter, Johnson 70 HP fuel filter, Johnson 90 HP fuel filter, Johnson 115 HP fuel filter, Johnson 140 HP fuel filter, Sierra 18-7716 replacement, Suzuki outboard fuel filter, marine four-stroke fuel filter, outboard fuel system maintenance

Item#:
7716P
Cross Reference#:
0765573
15410-60C00
15410-87J10
18-7716
5030702
5032323
765573
Manufacturer Item:
15410-87J10
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
8.65
Each
Mercury 135-200hp 2.0L 2.5L Johnson / Evinrude 150-235 V6 Xflow
Item#:
DV380
Cross Reference#:
13310
13310T1
133101
75661
802639
802639T
902639T
Manufacturer Item:
802639
Manufacturer:
Arco
Available:
In Stock
Your Price:
29.96
Each
Johnson Evinrude 185-225hp V6 V8 Looper
Item#:
DV387
Cross Reference#:
332276
332277
332278
397374
397887
5000333
584800
586392
Manufacturer Item:
397374
Manufacturer:
Arco
Available:
In Stock
Your Price:
31.76
Each
Mercury 30-60hp SportJet 175-250 Johnson/Evinrude 40-75hp
Item#:
206
Cross Reference#:
0377139
0379258
0769657
0775546
18-1154
18-1154
20080
21860
377139
377139
379258
53853
63742
63742T
769657
9-51202
Manufacturer Item:
63742T
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
14.55
Each
Mercury 135-300hp 2.5-3.0 V6 Johnson / Evinrude 120-300 V4 V6
Item#:
308
Cross Reference#:
0390641
0777375
18-1345
18-1396
21623
390641
41421
67923
67923T
777375
9-51204
93306-308U0-00
Manufacturer Item:
67923T
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
25.70
Each
Johnson/Evinrude 85-300hp 40-200 E-tec Mercury 200-300 DFI / XS / Pro XS
Item#:
387
Cross Reference#:
0387041
0769405
18-1353
22810
387041
5007190
769405
878758
88269
88269T
Manufacturer Item:
387041
Manufacturer:
Pro Marine
Available:
In Stock
Your Price:
36.70
Each
|◀ ◀ 1693 - 1704 of 2557 ▶ ▶|
View: