S2K Commerce - Products Dropdown
Actions
S2K Commerce - Order Entry
Actions
Outboard Motor Parts | OEM & Aftermarket
Shop OEM and aftermarket outboard motor parts for Mercury, Yamaha, Suzuki, Honda, Johnson / Evinrude / E-TEC, Tohatsu / Nissan, and Chrysler / Force engines. Pro Marine USA carries parts for routine maintenance, troubleshooting, repair, and complete marine engine rebuilds.
Browse by outboard manufacturer or engine system, or use our OEM parts lookup to identify the correct part number before ordering. Find cooling, fuel, ignition, electrical, internal engine, lower unit, steering, trim, service kit, gasket, seal, and rebuild parts in one place.
Shop Outboard Parts by Manufacturer
Chrysler / Force Outboard Parts for Chrysler and Force outboard repair 
Honda Outboard Honda cooling, fuel, electrical, and engine parts 
Johnson / Evinrude / E-TEC Outboard Johnson, Evinrude, E-TEC, and OMC replacement parts 
Mercury Outboard Mercury and Mariner maintenance, repair, and rebuild parts 
Suzuki Outboard Suzuki service, lower unit, fuel, and engine parts 
Tohatsu / Nissan Outboard Tohatsu and Nissan outboard replacement parts 
Yamaha Outboard Yamaha maintenance, repair, lower unit, and rebuild parts Find the Correct Outboard Part
Not sure which part fits your engine? Start with the engine manufacturer, horsepower, model number, serial number, and year whenever available.
Our OEM parts lookup lets you view factory parts diagrams and identify the original part number for many popular outboard engines. Once you have the OEM number, search Pro Marine to find available OEM and aftermarket replacement options.
Use Our OEM Parts Lookup »Shop Outboard Parts by Engine System
Outboard engines use several interconnected systems. Select your manufacturer above to browse the exact categories available for your engine, including the following common repair and maintenance areas.
Common Outboard Problems and Where to Start
- Engine overheating: inspect the water pump, impeller, thermostat, pressure-control components, cooling passages, and engine anodes.
- Hard starting or rough idle: check fuel delivery, carburetor or injector operation, spark plugs, ignition components, filters, and intake sealing.
- Weak spark or no spark: test ignition coils, stators, switch boxes or ignition modules, sensors, wiring, grounds, and related electrical components.
- Low compression or poor power: inspect pistons, rings, cylinder condition, head and powerhead gaskets, bearings, and other internal engine components.
- Milky gear lube: inspect prop shaft, driveshaft, shift shaft, bearing carrier, and other lower unit seals for water intrusion.
- Lower unit or gearcase noise: inspect bearings, gears, clutch components, shafts, and gear lube condition before continued operation.
- Trim or steering problems: inspect hydraulic fluid level, seals, hoses, trim motors, pumps, steering cylinders, and mechanical connections.
Why Buy Outboard Parts from Pro Marine USA?
- OEM and aftermarket replacement options for major outboard engine brands.
- Marine engine parts for routine maintenance, professional repair, and complete rebuild projects.
- OEM diagram and part-number lookup tools to help identify the correct component before ordering.
- Dealer pricing available for qualified marine repair businesses and dealers.
- Large selection of service kits, engine parts, lower unit components, fuel system parts, electrical parts, steering, and rigging products.
- Same-day weekday shipping available on qualifying in-stock orders placed before the shipping cutoff.
OEM and Aftermarket Outboard Parts
OEM parts are supplied by the original engine manufacturer and are designed for the specific engine application. Aftermarket parts are replacement components produced by independent marine parts manufacturers and may provide additional availability or value for many common repairs.
Pro Marine carries both genuine OEM parts and quality aftermarket replacement parts for many outboard maintenance, repair, and rebuild applications. Always confirm fitment using the engine model, serial number, horsepower, year range, or OEM part number when available.
Frequently Asked Questions
How do I find the correct parts for my outboard motor?
Start by identifying the engine manufacturer, horsepower, model number, serial number, and year. Select the manufacturer above to browse by engine system, or use the OEM parts lookup to locate the original part number from a factory diagram.
Can I search Pro Marine by OEM part number?
Yes. If you already have the OEM part number, enter it into the Pro Marine site search to locate available OEM and aftermarket replacement options. If you do not know the part number, use the OEM parts lookup first.
What information should I have before ordering an outboard part?
Have the engine manufacturer, horsepower, model number, serial number, and year whenever possible. An OEM part number from the original component or parts diagram is especially helpful because visually similar parts may fit different engine families.
What is the difference between OEM and aftermarket outboard parts?
OEM parts come from the original engine manufacturer. Aftermarket parts are replacement components manufactured by other marine parts companies for compatible applications. Pro Marine carries both OEM and aftermarket options across many common outboard engine systems.
Are aftermarket outboard motor parts reliable?
Quality aftermarket marine parts are commonly used for maintenance, professional repair, and engine rebuilding. The best option depends on the application, manufacturer, availability, and customer preference.
Do you carry parts for older outboard motors?
Yes. Pro Marine carries parts for many older Mercury, Mariner, Johnson, Evinrude, Chrysler, Force, Yamaha, Honda, Suzuki, Nissan, and Tohatsu outboards. Availability varies by engine family and component.
What outboard parts are commonly replaced during routine maintenance?
Common maintenance items include engine oil, oil filters, fuel filters, spark plugs, water pump impellers, complete water pump kits, thermostats, gear lube, drain plug seals, anodes, and manufacturer-specific service kit components.
Fitment Tip: Outboard parts can vary by model, serial range, horsepower, and production year. Confirm the OEM part number or engine identification information whenever possible before ordering.
648-14385-00-00
Mercury Shock Rod Assembly 8M0060145
The Mercury 8M0060145 Shock Rod Assembly is an OEM component used in the power trim system on select Mercury outboards. It helps control movement within the trim assembly and supports smooth, stable engine positioning during operation.
Fitment Overview
This shock rod assembly fits Mercury 105HP Jet, 135HP, and 150HP outboards using the earlier power trim assembly design for serial numbers 2B752836 and below.
Compatibility
| Engine Model | Horsepower | Serial Range |
|---|---|---|
| Mercury Jet | 105 HP | 2B752836 and Below |
| Mercury FourStroke | 135 HP | 2B752836 and Below |
| Mercury FourStroke | 150 HP | 2B752836 and Below |
Fits These Serial Ranges
Confirmed application: Mercury 105HP Jet, 135HP, and 150HP models using the earlier power trim assembly design for serial numbers 2B752836 and below.
Important: This part is for engines before the serial break. If your engine is
serial number 2B752836 and up, you will need the updated shock rod kit:
Mercury Shock Rod Kit 8M0168235 for 2B752836 and Up
Repair Your Existing Shock Rod Cap Instead
If your existing shock rod cap housing is still in good condition and only the seals are leaking or worn, you may be able to repair your current assembly instead of replacing the complete shock rod assembly.
Pro Marine now offers an all-new replacement seal kit designed for rebuilding compatible Mercury shock rod cap assemblies:
Pro Marine 8M0060145P Shock Rod Cap Seal Kit
- Lower-cost alternative to full assembly replacement
- Designed for compatible Mercury shock rod cap assemblies
- Ideal for leaking or worn seal repairs
- Great option when the original cap housing is still reusable
Part Numbers and Cross References
| Type | Part Number |
|---|---|
| Mercury OEM | 8M0060145 |
| Application | Shock Rod Assembly |
| System | Power Trim Assembly |
What This Part Is Used For
This shock rod assembly is used inside the power trim assembly to help control internal movement and support smooth trim operation. It plays a key role in stabilizing the engine during trim and reducing stress on trim system components.
- Used in Mercury power trim assemblies
- Supports smooth trim and tilt operation
- Helps control internal movement of trim components
- Designed for earlier trim assembly configurations
If you are servicing the trim system on a compatible Mercury outboard, this component may need replacement due to wear or internal damage.
System Function and Connections
- System Type: Hydraulic power trim
- Location: Inside the power trim assembly
- Related Components: Trim pump, pistons, cylinders, and bracket components
FAQ
What does Mercury 8M0060145 fit?
It fits Mercury 105HP Jet, 135HP, and 150HP outboards with serial numbers 2B752836 and below.
How do I know if I need this or the updated kit?
Check your serial number. If your engine is 2B752836 and below, use this part. If it is above that, use the updated 8M0168235 kit.
Can I repair my existing shock rod cap instead of replacing the full assembly?
Yes. If your cap housing is still reusable and only the seals are worn or leaking, the Pro Marine 8M0060145P seal kit may be a lower-cost repair option.
Is this part used in the steering system?
No. This is a component of the power trim assembly.
Why is the serial break important?
Mercury changed the trim system design, requiring different components before and after the serial break.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 (continental U.S.).
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1–5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Items must be new, unused, and in original packaging.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers
8M0060145, Mercury shock rod assembly, Mercury 105HP Jet trim rod, Mercury 135HP trim rod, Mercury 150HP trim rod, Mercury trim system 2B752836 and below, 8M0060145P, Mercury shock rod seal kit, Pro Marine shock rod cap seal kit
CDI Unit 9369585540P
The 9369585540P CDI Unit is a replacement ignition module used on Yamaha and Mercury 2-cylinder 2-stroke outboards. This unit controls ignition timing and spark delivery, ensuring reliable starting and smooth engine performance.
Fitment Overview
This CDI unit replaces multiple Yamaha and Mercury ignition modules, including 695-85540-10-00, 695-85540-11-00, 695-85540-12-00, 43077M, and 43077T. These part numbers are used across small horsepower 2-cylinder outboards.
Compatibility
| Brand | Horsepower | Engine Type |
|---|---|---|
| Yamaha | 9.9 HP | 2-Cylinder 2-Stroke |
| Yamaha | 15 HP | 2-Cylinder 2-Stroke |
| Yamaha | 25 HP | 2-Cylinder 2-Stroke |
| Mercury / Mariner | 9.9 HP | 2-Cylinder 2-Stroke |
| Mercury / Mariner | 15 HP | 2-Cylinder 2-Stroke |
| Mercury / Mariner | 20 HP | 2-Cylinder 2-Stroke |
| Mercury / Mariner | 25 HP | 2-Cylinder 2-Stroke |
This ignition module is used across multiple model years depending on ignition system configuration. Always confirm using your original CDI number or engine diagram.
Fits These Serial Ranges
This CDI unit does not follow a single serial break and is used across multiple Yamaha and Mercury 2-cylinder ignition systems.
Important: Match your existing CDI number to one of the cross references below to confirm correct fitment.
Part Numbers and Cross References
| Type | Part Number |
|---|---|
| Pro Marine | 9369585540P |
| Yamaha OEM | 695-85540-10-00 |
| Yamaha OEM | 695-85540-11-00 |
| Yamaha OEM | 695-85540-12-00 |
| CDI Electronics | 117-695-11 |
| CDI Electronics | 17-69511 |
| Sierra | 18-5131 |
| Mercury OEM | 43077M |
| Mercury OEM | 43077T |
| Mercury OEM | 69450M |
What This Part Is Used For
The CDI (Capacitor Discharge Ignition) unit stores and releases electrical energy to fire the spark plugs at the correct time. It is a critical component in the ignition system for proper engine operation.
- Controls ignition timing
- Delivers spark to ignition coils
- Ensures reliable starting
- Supports smooth engine performance
A faulty CDI unit can cause no spark, intermittent spark, misfires, or engine shutdown.
FAQ
What engines does this CDI fit?
It fits Yamaha and Mercury 2-cylinder 2-stroke outboards in the 9.9HP to 25HP range.
How do I confirm fitment?
Match your existing CDI part number to one of the cross references listed above.
Is this a Mercury switch box?
Yes, this unit replaces Mercury switch box numbers such as 43077M and 43077T.
What are signs of a bad CDI?
No spark, weak spark, intermittent misfire, or engine not starting.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 (continental U.S.).
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1–5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Items must be new, unused, and in original packaging.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers
9369585540P, 695-85540-10-00, 695-85540-11-00, 695-85540-12-00, 117-695-11, 17-69511, 18-5131, 43077M, 43077T, 69450M
17-69511
18-5131
43077M
43077T
69450M
695-85540-10-00
695-85540-11-00
695-85540-12-00
9-37500
92520M
Pro Marine Shock Rod Cap Seal Kit 8M0060145P
The Pro Marine 8M0060145P Shock Rod Cap Seal Kit is designed to rebuild the cap assembly used on compatible Mercury 8M0060145 Shock Rod Assemblies.
This seal kit provides a lower-cost repair option for customers whose existing shock rod cap housing is still reusable but the seals are leaking, damaged, or worn.
Designed For These Applications
This seal kit is used with the Mercury 8M0060145 Shock Rod Assembly found on select Mercury trim and tilt systems used on:
| Engine Model | Horsepower | Serial Range |
|---|---|---|
| Mercury Jet | 105 HP | 2B752836 and Below |
| Mercury FourStroke | 135 HP | 2B752836 and Below |
| Mercury FourStroke | 150 HP | 2B752836 and Below |
What This Seal Kit Repairs
This kit is specifically intended to reseal the shock rod cap assembly used on the Mercury 8M0060145 hydraulic shock rod assembly.
It is commonly used to repair:
- Hydraulic fluid leaks
- Worn cap seals
- Trim fluid seepage
- Aging hydraulic seal components
- Preventive trim system maintenance
If your cap assembly is physically damaged, heavily corroded, cracked, or otherwise not reusable, you may need the complete shock rod assembly instead.
Need the Complete Shock Rod Assembly?
If your original shock rod cap housing is damaged or not suitable for rebuilding, check out the complete OEM Mercury shock rod assembly:
OEM Mercury 8M0060145 Shock Rod Assembly
- Complete Mercury shock rod assembly
- OEM Mercury / Quicksilver component
- Used when the original cap housing cannot be resealed
- Fits select Mercury 105 Jet, 135HP, and 150HP applications
Part Numbers and Cross References
| Type | Part Number |
|---|---|
| Pro Marine | 8M0060145P |
| Used With | Mercury 8M0060145 |
| Application | Shock Rod Cap Seal Kit |
| System | Hydraulic Power Trim |
What This Kit Is Used For
This kit is used during hydraulic trim and tilt system service to rebuild the cap portion of compatible Mercury shock rod assemblies.
Replacing leaking or worn seals can help restore trim system sealing and reduce hydraulic fluid leakage without replacing the complete assembly.
This is often a more economical repair solution when the original cap housing itself is still reusable.
Features and Benefits
- Pro Marine shock rod cap seal kit
- Designed for Mercury 8M0060145 shock rod assemblies
- Lower-cost alternative to replacing the full assembly
- Helps repair leaking hydraulic trim systems
- Designed for reusable cap housings
- Supports hydraulic trim and tilt maintenance
- Ideal for preventive trim system service
- Marine-grade replacement seals
System Function and Connections
- System Type: Hydraulic power trim
- Application: Shock rod cap reseal
- Used With: Mercury 8M0060145 shock rod assembly
- Related Components: Trim cylinders, pistons, trim pump, hydraulic assemblies
FAQ
What does the Pro Marine 8M0060145P fit?
This seal kit is designed for the cap assembly used on Mercury 8M0060145 shock rod assemblies.
Can this repair a leaking trim assembly?
Yes. This kit is intended to repair leaking or worn seals inside compatible shock rod cap assemblies.
Does this replace the complete shock rod assembly?
No. This kit is only for rebuilding the cap portion of the assembly.
What if my cap housing is damaged?
If the cap housing is cracked, heavily corroded, or otherwise not reusable, you should replace the complete shock rod assembly.
Where can I find the complete shock rod assembly?
You can view the OEM Mercury 8M0060145 Shock Rod Assembly linked above.
Why would I use this kit instead of replacing the full assembly?
This kit can be a lower-cost repair option when only the seals have failed and the original cap housing is still reusable.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 continental U.S.
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1–5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Hydraulic trim components should be installed only after confirming correct fitment.
- Items must be new, unused, and in original packaging.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers
8M0060145P, Mercury shock rod seal kit, Mercury shock rod cap seal kit, Mercury trim seal kit, Mercury hydraulic trim repair, Mercury shock rod rebuild kit, Mercury 8M0060145 seals, Mercury trim cap seals, Mercury hydraulic trim seals, Mercury 105 Jet trim repair, Mercury 135HP trim seals, Mercury 150HP trim seals, Mercury trim cap rebuild
69J-45332-00-94
69J82563P Yamaha 25-300 HP Trim and Tilt Switch
The Pro Marine 69J82563P Trim and Tilt Switch is an aftermarket replacement for select Yamaha outboards using the 69J and related 704-series trim switch assemblies.
This switch is used across select Yamaha 25-300 HP 2-stroke and 4-stroke applications, including F, LF, T, VF, VZ, Z, and LZ engine families. Exact model and year verification is still required before ordering.
Product Information
- Pro Marine Part Number: 69J82563P
- Brand: Pro Marine
- Part Type: Power Trim and Tilt Switch
- General Fitment: Select Yamaha 25-300 HP
- Engine Types: Select 2-Stroke and 4-Stroke Applications
- Primary OEM Reference: 69J-82563-00-00
- Superseding Yamaha Reference: 69J-82563-01-00
- OEM Version Available: Yamaha 69J-82563-00-00
Important Fitment Note
This switch does not fit every Yamaha outboard from 25-300 HP. The horsepower range is a summary of the supplied Yamaha application data.
Yamaha used different trim and tilt switches depending on model year, engine family, control arrangement, and rigging configuration.
Always verify your complete Yamaha engine model or original trim-switch part number before ordering.
OEM and Cross Reference Numbers
| Part Number | Relationship |
|---|---|
| 69J82563P | Pro Marine Aftermarket |
| 69J-82563-00-00 | Yamaha OEM Reference |
| 69J-82563-01-00 | Yamaha OEM - Supersedes 69J-82563-00-00 |
| 704-82563-40-00 | Earlier Yamaha Reference |
| 704-82563-41-00 | Earlier Yamaha Reference |
| 704-82563-42-00 | Later Yamaha 704-Series Reference |
Yamaha OEM 69J-82563-00-00 Trim and Tilt Switch
Prefer genuine Yamaha OEM? Pro Marine USA also carries the Yamaha version of this trim and tilt switch. Yamaha 69J-82563-00-00 has been superseded by 69J-82563-01-00.
What This Part is Used For
The trim and tilt switch provides the operator input used to raise or lower the outboard through the compatible Yamaha power trim and tilt system.
It is commonly replaced when the original switch becomes damaged, intermittent, corroded, or no longer reliably commands one or both trim directions.
Compatible Yamaha Applications
The supplied Yamaha application data has been grouped below into customer-readable engine families and year ranges.
| Engine Family | Years | Engine Type |
|---|---|---|
| F25 / T25 | 2006-Present | 4-Stroke |
| F40 | 2006-Present | 4-Stroke |
| F50 / T50 | 2006-Present | 4-Stroke |
| F60 / T60 | 2006-Present | 4-Stroke |
| F70 | 2006-Present | 4-Stroke |
| F115 / LF115 / VF115 | 2006-Present | 4-Stroke |
| F130 / LF130 | 2006-Present | 4-Stroke |
| F150 / LF150 / FL150 | 2004-Present | 4-Stroke |
| VF150 | 2006-Present | 4-Stroke |
| F175 / VF175 | 2006-Present | 4-Stroke |
| F200 / LF200 | 2002-Present | 4-Stroke |
| VF200 | 2006-Present | 4-Stroke |
| VZ200 | 2005-Present | 2-Stroke HPDI |
| F225 / LF225 | 2002-Present | 4-Stroke |
| VF225 | 2006-Present | 4-Stroke |
| VZ225 | 2003-Present | 2-Stroke HPDI |
| F250 / LF250 | 2005-Present | 4-Stroke |
| VF250 | 2006-Present | 4-Stroke |
| VZ250 | 2003-Present | 2-Stroke HPDI |
| Z250 / LZ250 | 2003-Present | 2-Stroke HPDI |
| F300 / LF300 | 2006-Present | 4-Stroke |
| VZ300 | 2004-Present | 2-Stroke HPDI |
| Z300 / LZ300 | 2004-Present | 2-Stroke HPDI |
Common Symptoms and Replacement Reasons
- Trim or tilt does not respond when the switch is pressed.
- UP or DOWN function operates intermittently.
- One direction works while the other does not.
- Switch housing or button is damaged.
- Wiring or connector at the original switch is damaged or corroded.
- Water intrusion has caused unreliable switch operation.
A non-operating trim system is not always caused by the switch. Wiring, connectors, relays, fuses, battery voltage, and the trim motor should also be checked during diagnosis.
Installation Tips
- Disconnect battery power before servicing the trim and tilt electrical system.
- Compare the replacement switch and connector with the original part before installation.
- Inspect nearby wiring and terminals for corrosion or damage.
- Route wiring so it cannot be pinched, stretched, or chafed.
- After installation, verify both UP and DOWN trim functions.
Key Features and Benefits
- Pro Marine Brand: Aftermarket replacement for listed Yamaha applications.
- Broad Application Coverage: Select Yamaha 25-300 HP 2-stroke and 4-stroke outboards.
- OEM Cross References: Replaces multiple Yamaha 69J and 704-series trim-switch numbers.
- UP and DOWN Control: Provides trim and tilt switch input on compatible systems.
- OEM Version Available: Genuine Yamaha alternative is also available from Pro Marine USA.
Frequently Asked Questions
What does Pro Marine 69J82563P fit?
It fits select Yamaha 25-300 HP 2-stroke and 4-stroke outboards, including specific F, LF, T, VF, VZ, Z, and LZ model families.
Does it fit every Yamaha 25-300 HP outboard?
No. The horsepower range is only a general fitment summary. Exact engine model and original trim-switch configuration must be verified.
Does 69J82563P replace Yamaha 69J-82563-00-00?
Yes. 69J-82563-00-00 is one of the primary Yamaha OEM references for this part.
What supersedes Yamaha 69J-82563-00-00?
Yamaha 69J-82563-01-00 supersedes the earlier 69J-82563-00-00 number.
Is a genuine Yamaha version available?
Yes. Pro Marine USA also carries the Yamaha OEM trim and tilt switch .
If my engine will not trim, is the switch definitely bad?
No. Trim problems can also be caused by relays, wiring, connectors, fuses, battery voltage, or the trim motor. The circuit should be tested before replacing parts.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 continental U.S.
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1-5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Parts must be new, unused, and in original packaging.
- Installed parts are not returnable.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers
69J82563P, 69J-82563-00-00, 69J-82563-01-00, 704-82563-40-00, 704-82563-41-00, 704-82563-42-00, 69J825630000, 69J825630100, 704825634000, 704825634100, 704825634200
Searchable Terms
Yamaha 25-300 HP trim switch, Yamaha trim and tilt switch, Yamaha power trim switch, Yamaha 2-stroke trim switch, Yamaha 4-stroke trim switch, Yamaha HPDI trim switch, Yamaha F150 trim switch, Yamaha F200 trim switch, Yamaha F225 trim switch, Yamaha F250 trim switch, Yamaha F300 trim switch, Yamaha VZ250 trim switch, 69J-82563-00-00 replacement, 69J-82563-01-00 replacement, Pro Marine 69J82563P
69J-82563-01-00
704-82563-40-00
704-82563-41-00
704-82563-42-00
Fits Mercury 500R 4.6L V8 Supercharged Verado Outboards
Designed specifically for Mercury 500R 4.6L V8 supercharged Verado engines. The 8M0210486 Supercharger Belt is an OEM replacement belt used in the supercharger drive system. This belt is critical for maintaining proper boost pressure and ensuring peak engine performance.
Compatibility
This supercharger belt is used exclusively on Mercury 500R 4.6L V8 supercharged Verado outboards. It is part of the supercharger drive system and is essential for proper engine operation.
Application Chart
| Brand | Engine Model | Displacement | Engine Type | Component |
|---|---|---|---|---|
| Mercury Racing | 500R Verado | 4.6L V8 | Supercharged 4-Stroke | Supercharger Drive Belt |
Always confirm compatibility using your engine serial number and existing belt part number before ordering.
Part Numbers & Cross References
| Reference Type | Part Number |
|---|---|
| OEM / Pro Marine Part | 8M0210486 |
What This Part Is Used For
The supercharger belt drives the supercharger system, which compresses incoming air to increase engine power output. In the Mercury 500R platform, this system is critical for achieving the engine’s high-performance output.
Over time, belts can wear due to heat, load, and continuous operation. Replacing the belt as part of routine maintenance helps prevent loss of boost, reduced performance, or unexpected failure.
Frequently Asked Questions
What engines does this belt fit?
This belt fits Mercury Racing 500R 4.6L V8 supercharged Verado outboards only.
Is this used on standard Verado models?
No. This belt is specific to the supercharged 500R platform and does not fit standard Verado engines.
What does the supercharger belt do?
It drives the supercharger, which provides boost pressure and increased engine performance.
When should this belt be replaced?
It should be inspected regularly and replaced when signs of wear such as cracking, fraying, or slipping are present.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 (continental U.S.).
- Orders ship via UPS, USPS, or FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical ground delivery time is 1–5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Items must be new, unused, and in original packaging.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers
Part Number: 8M0210486
Common Search Terms: Mercury 500R supercharger belt, Verado 500R belt, 4.6L V8 supercharger belt, marine supercharger drive belt
8M0062859
8M6003035
885349500
814496M
814496M
82263M
82263M
93210-09156-00
93210-09165-00
93210-09350-00
93210-09729-00
93210-09754-00
93210-09811-00
8886774