S2K Commerce - Products Dropdown
Actions
S2K Commerce - Order Entry
Actions
Outboard Motor Parts | OEM & Aftermarket
Shop OEM and aftermarket outboard motor parts for Mercury, Yamaha, Suzuki, Honda, Johnson / Evinrude / E-TEC, Tohatsu / Nissan, and Chrysler / Force engines. Pro Marine USA carries parts for routine maintenance, troubleshooting, repair, and complete marine engine rebuilds.
Browse by outboard manufacturer or engine system, or use our OEM parts lookup to identify the correct part number before ordering. Find cooling, fuel, ignition, electrical, internal engine, lower unit, steering, trim, service kit, gasket, seal, and rebuild parts in one place.
Shop Outboard Parts by Manufacturer
Chrysler / Force Outboard Parts for Chrysler and Force outboard repair 
Honda Outboard Honda cooling, fuel, electrical, and engine parts 
Johnson / Evinrude / E-TEC Outboard Johnson, Evinrude, E-TEC, and OMC replacement parts 
Mercury Outboard Mercury and Mariner maintenance, repair, and rebuild parts 
Suzuki Outboard Suzuki service, lower unit, fuel, and engine parts 
Tohatsu / Nissan Outboard Tohatsu and Nissan outboard replacement parts 
Yamaha Outboard Yamaha maintenance, repair, lower unit, and rebuild parts Find the Correct Outboard Part
Not sure which part fits your engine? Start with the engine manufacturer, horsepower, model number, serial number, and year whenever available.
Our OEM parts lookup lets you view factory parts diagrams and identify the original part number for many popular outboard engines. Once you have the OEM number, search Pro Marine to find available OEM and aftermarket replacement options.
Use Our OEM Parts Lookup »Shop Outboard Parts by Engine System
Outboard engines use several interconnected systems. Select your manufacturer above to browse the exact categories available for your engine, including the following common repair and maintenance areas.
Common Outboard Problems and Where to Start
- Engine overheating: inspect the water pump, impeller, thermostat, pressure-control components, cooling passages, and engine anodes.
- Hard starting or rough idle: check fuel delivery, carburetor or injector operation, spark plugs, ignition components, filters, and intake sealing.
- Weak spark or no spark: test ignition coils, stators, switch boxes or ignition modules, sensors, wiring, grounds, and related electrical components.
- Low compression or poor power: inspect pistons, rings, cylinder condition, head and powerhead gaskets, bearings, and other internal engine components.
- Milky gear lube: inspect prop shaft, driveshaft, shift shaft, bearing carrier, and other lower unit seals for water intrusion.
- Lower unit or gearcase noise: inspect bearings, gears, clutch components, shafts, and gear lube condition before continued operation.
- Trim or steering problems: inspect hydraulic fluid level, seals, hoses, trim motors, pumps, steering cylinders, and mechanical connections.
Why Buy Outboard Parts from Pro Marine USA?
- OEM and aftermarket replacement options for major outboard engine brands.
- Marine engine parts for routine maintenance, professional repair, and complete rebuild projects.
- OEM diagram and part-number lookup tools to help identify the correct component before ordering.
- Dealer pricing available for qualified marine repair businesses and dealers.
- Large selection of service kits, engine parts, lower unit components, fuel system parts, electrical parts, steering, and rigging products.
- Same-day weekday shipping available on qualifying in-stock orders placed before the shipping cutoff.
OEM and Aftermarket Outboard Parts
OEM parts are supplied by the original engine manufacturer and are designed for the specific engine application. Aftermarket parts are replacement components produced by independent marine parts manufacturers and may provide additional availability or value for many common repairs.
Pro Marine carries both genuine OEM parts and quality aftermarket replacement parts for many outboard maintenance, repair, and rebuild applications. Always confirm fitment using the engine model, serial number, horsepower, year range, or OEM part number when available.
Frequently Asked Questions
How do I find the correct parts for my outboard motor?
Start by identifying the engine manufacturer, horsepower, model number, serial number, and year. Select the manufacturer above to browse by engine system, or use the OEM parts lookup to locate the original part number from a factory diagram.
Can I search Pro Marine by OEM part number?
Yes. If you already have the OEM part number, enter it into the Pro Marine site search to locate available OEM and aftermarket replacement options. If you do not know the part number, use the OEM parts lookup first.
What information should I have before ordering an outboard part?
Have the engine manufacturer, horsepower, model number, serial number, and year whenever possible. An OEM part number from the original component or parts diagram is especially helpful because visually similar parts may fit different engine families.
What is the difference between OEM and aftermarket outboard parts?
OEM parts come from the original engine manufacturer. Aftermarket parts are replacement components manufactured by other marine parts companies for compatible applications. Pro Marine carries both OEM and aftermarket options across many common outboard engine systems.
Are aftermarket outboard motor parts reliable?
Quality aftermarket marine parts are commonly used for maintenance, professional repair, and engine rebuilding. The best option depends on the application, manufacturer, availability, and customer preference.
Do you carry parts for older outboard motors?
Yes. Pro Marine carries parts for many older Mercury, Mariner, Johnson, Evinrude, Chrysler, Force, Yamaha, Honda, Suzuki, Nissan, and Tohatsu outboards. Availability varies by engine family and component.
What outboard parts are commonly replaced during routine maintenance?
Common maintenance items include engine oil, oil filters, fuel filters, spark plugs, water pump impellers, complete water pump kits, thermostats, gear lube, drain plug seals, anodes, and manufacturer-specific service kit components.
Fitment Tip: Outboard parts can vary by model, serial range, horsepower, and production year. Confirm the OEM part number or engine identification information whenever possible before ordering.
Pro Marine Yamaha 704 Dual Engine Mechanical Control
Yamaha 704 Dual Engine Top Mount Remote Control Box - 48207P
Pro Marine 48207P is an aftermarket replacement Yamaha 704 dual-engine top-mount remote control box for compatible Yamaha outboards using mechanical throttle and shift controls.
This control is designed for twin-engine mechanical-control installations and includes the dual control switch and wire harness used with the applicable Yamaha 704 rigging system.
Pro Marine 48207P replaces a wide range of Yamaha 704 control numbers, including 704-48207-P1-00, 704-48207-P0-00, 704-48207-R0-00, 704-48207-R1-00 and 704-48207-R2-00, along with several earlier 704-48207-xx-xx numbers.
Part Type: Dual Engine Top Mount Remote Control
Brand: Pro Marine
OEM or Aftermarket: Aftermarket
Application: Yamaha Outboard
Control Type: Mechanical Throttle and Shift
Engine Configuration: Dual Engine
Mounting Style: Top / Surface Mount
Manufacturer Item #: 704-48207-P1-00
Pro Marine Item #: 48207P
Compatible Applications
Pro Marine 48207P is designed for compatible Yamaha dual-outboard installations using the Yamaha 704-style top-mount mechanical remote control system.
| Application | Control Type | Mounting |
|---|---|---|
| Yamaha Dual Outboard | Mechanical Throttle and Shift | Top / Surface Mount |
| Yamaha 704 Control System | Dual Lever Mechanical Control | Console Top Mount |
This is a dual-engine Yamaha mechanical-control box.
Do not select this control solely by engine horsepower. Yamaha used different control systems depending on engine generation, rigging style and whether the engines use mechanical or electronic controls.
Before ordering, verify that your installation uses a compatible Yamaha 704 top-mount mechanical control and confirm that the original control crosses to one of the listed OEM numbers.
OEM and Cross Reference Numbers
Pro Marine 48207P replaces or cross-references the following Yamaha 704 dual-engine remote-control numbers.
| Brand / Type | Part Number |
|---|---|
| Pro Marine | 48207P |
| Yamaha OEM | 704-48207-P1-00 |
| Yamaha OEM | 704-48207-P0-00 |
| Yamaha OEM | 704-48207-R0-00 |
| Yamaha OEM | 704-48207-R1-00 |
| Yamaha OEM | 704-48207-R2-00 |
| Yamaha OEM | 704-48207-10-00 |
| Yamaha OEM | 704-48207-20-00 |
| Yamaha OEM | 704-48207-21-00 |
| Yamaha OEM | 704-48207-22-00 |
| Yamaha OEM | 704-48207-23-00 |
| Yamaha OEM | 704-48207-23-10 |
| Yamaha OEM | 704-48207-30-00 |
| Yamaha OEM | 704-48207-31-00 |
| Yamaha OEM | 704-48207-39-00 |
What This Control is Used For
The remote control box provides the operator with independent throttle and shift control for two mechanically controlled Yamaha outboards.
Each control lever operates its corresponding engine, allowing the operator to shift each engine between forward, neutral and reverse while controlling engine speed.
Dual-engine controls are especially useful for maneuvering because each engine can be shifted and throttled independently.
Yamaha 704 Top Mount Design
The Yamaha 704-style control is a surface-mounted / top-mounted binnacle control designed to install on top of the helm or console.
Unlike a side-mount control box, the operating mechanism is positioned above the console surface with the control hardware mounted below the panel.
This style is commonly used on center consoles, offshore boats and other twin-engine installations where a centrally positioned dual control is preferred.
Mechanical Throttle and Shift Control
Pro Marine 48207P is intended for mechanically controlled Yamaha outboards.
Mechanical controls use physical control cables between the remote control and the engines to operate throttle and shift functions.
This should not be confused with later electronic or drive-by-wire Yamaha control systems. If your engines use electronic throttle and shift, verify the correct electronic control before ordering.
Before replacing a Yamaha control box, determine whether the engines use mechanical throttle and shift cables or an electronic control system.
Pro Marine 48207P is for the compatible Yamaha 704 mechanical control system.
Dual Engine Control
This control is specifically intended for a two-engine installation.
Each lever controls one engine so the operator can independently manage throttle and gear selection for the port and starboard engines.
If you have a single-engine Yamaha installation, Pro Marine also carries a separate single-engine top-mount control. Do not substitute the dual-engine 48207P for a single-engine control application.
Includes Dual Switch and Wire Harness
The current Pro Marine listing identifies 48207P as including the dual switch and wire harness used with the compatible Yamaha 704 dual-engine control configuration.
Always compare the electrical connector configuration with the control being removed before installation.
Common Reasons to Replace a Yamaha 704 Control Box
- Excessive control-lever play
- Stiff or inconsistent lever movement
- Internal mechanical wear
- Damaged control housing
- Worn throttle or shift mechanism
- Damaged electrical switches or harness
- Corrosion inside an older control assembly
- Complete twin-engine rerigging or restoration
Installation Tips
- Confirm both engines use mechanical throttle and shift controls.
- Verify the existing control crosses to one of the listed Yamaha 704 numbers.
- Compare the control-cable connections before removing the original control.
- Inspect both sets of throttle and shift cables while the control is removed.
- Replace cables that are stiff, corroded, damaged or excessively worn.
- Verify the electrical harness and switch connectors before installation.
- Adjust the control cables according to Yamaha service procedures.
- Verify forward, neutral and reverse operation on both engines.
- Check that both engines return fully to neutral before operation.
- Test all control switches after installation.
Key Features and Benefits
- Pro Marine aftermarket Yamaha remote control box
- Pro Marine item number 48207P
- Yamaha 704-style top-mount control
- Designed for dual-engine installations
- Mechanical throttle and shift control
- Independent port and starboard engine control
- Includes dual switch and wire harness
- Replaces numerous Yamaha 704-48207 control numbers
- Current manufacturer reference 704-48207-P1-00
- Suitable for compatible Yamaha mechanical-control rigging systems
FAQ
What is Pro Marine 48207P?
It is a replacement Yamaha 704 dual-engine top-mount mechanical
remote control box.
Is 48207P for one engine or two engines?
This control is designed for a dual-engine installation.
Is this a Yamaha 704 control?
Yes. Pro Marine lists 48207P as a replacement
Yamaha 704 top-mount dual remote control.
Is this a mechanical control?
Yes. 48207P is for compatible Yamaha engines using
mechanical throttle and shift controls.
Will this work with Yamaha electronic controls?
No. This control is intended for the compatible Yamaha mechanical-control
system. Electronic throttle-and-shift systems use different controls.
Does 48207P replace Yamaha 704-48207-P1-00?
Yes. Pro Marine identifies 704-48207-P1-00 as the
manufacturer reference for 48207P.
Does it replace 704-48207-P0-00?
Yes. 704-48207-P0-00 is included in the supplied and
verified cross-reference list.
Does it replace the older 704-48207-20-00 and 704-48207-23-00 controls?
Yes. Those numbers are included among the Yamaha OEM cross references
for this control.
Does the control include wiring?
The current Pro Marine listing states that the control includes the
dual switch and wire harness.
Is this top mount or side mount?
This is a top / surface mount Yamaha 704-style control
designed to install on the top of the helm or console.
Will it fit every Yamaha outboard?
No. Verify that both engines use the compatible Yamaha mechanical-control
rigging system and that the original control crosses to one of the listed
OEM numbers before ordering.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 continental U.S.
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1-5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Parts must be new, unused, and in original packaging.
- Installed parts are not returnable.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers
48207P, 704-48207-P0-00, 704-48207-P1-00, 704-48207-R0-00, 704-48207-R1-00, 704-48207-R2-00, 704-48207-10-00, 704-48207-20-00, 704-48207-21-00, 704-48207-22-00, 704-48207-23-00, 704-48207-23-10, 704-48207-30-00, 704-48207-31-00, 704-48207-39-00
Searchable Terms
Yamaha 704 control, Yamaha dual control box, Yamaha twin engine control, Yamaha top mount control, Yamaha surface mount control, Yamaha mechanical control box, Yamaha dual throttle control, Yamaha twin outboard control, Yamaha remote control box, Yamaha binnacle control, Yamaha 704 dual control, Yamaha 704-48207-P1-00, Pro Marine Yamaha control
704-48207-P0-00
704-48207-P1-00
704-48207-P1-00
704-48207-R0-00
704-48207-R1-00
704-48207-R2-00
704-48207-10-00
704-48207-20-00
704-48207-21-00
704-48207-22-00
704-48207-23-00
704-48207-23-10
704-48207-30-00
704-48207-31-00
704-48207-39-00
704-48205-B1-00
704-48205-P0-00
704-48205-P1-00
704-48205-R0-00
704-48205-R1-00
704-48205-R2-00
704-48205-10-00
704-48205-11-00
704-48205-12-00
704-48205-13-00
704-48205-14-00
Mercury OEM 8M4507538 14-Pin Gen 2 Binnacle Top Mount Control
The Mercury 8M4507538 Remote Control is a genuine Mercury OEM console / binnacle-mount control for compatible Mercury mechanical-control rigging systems using a 14-pin electrical connection and Gen 2-style control cables.
This top-mount control cross-references Mercury part numbers 8M0041431, 8M0059686, and 883711A12. Pro Marine USA also stocks the Pro Marine 8M0059686P aftermarket version for this application.
Product Information
- Part Number: 8M4507538
- Brand: Genuine Mercury OEM
- Part Type: Binnacle / Top Mount Remote Control
- Application: Compatible Mercury Mechanical-Control Rigging
- Electrical Connection: 14-Pin
- Control Cable Type: Mercury Gen 2 Style
- Mounting Style: Console / Binnacle / Top Mount
- Aftermarket Alternative: Pro Marine 8M0059686P
Important Fitment Note
Do not select this remote control by engine horsepower alone. Compatibility is determined by the Mercury rigging system used on the boat.
This control is for compatible Mercury applications using a 14-pin electrical connection and Gen 2-style mechanical throttle and shift control cables.
Before ordering, verify the electrical connector, control-cable style, mounting configuration, and original remote-control part number. Similar-looking Mercury controls may use a different harness connection, cable generation, or control system.
OEM and Cross Reference Numbers
Mercury 8M4507538 is associated with the following Mercury remote-control numbers for this compatible top-mount, 14-pin / Gen 2 cable application.
| Part Number | Brand / Relationship |
|---|---|
| 8M4507538 | Genuine Mercury OEM |
| 8M0059686 | Mercury OEM Cross Reference |
| 8M0041431 | Mercury OEM Cross Reference |
| 883711A12 | Mercury OEM Cross Reference |
| 8M0059686P | Pro Marine Aftermarket Alternative |
What This Control is Used For
The Mercury binnacle control provides the helm interface for mechanical throttle and shift operation on compatible Mercury installations.
The control mounts on top of the boat's console or helm and connects to the compatible Mercury rigging system using Gen 2-style mechanical control cables and the required 14-pin electrical connection.
It can be used when replacing a damaged or worn original control or when rigging a compatible Mercury mechanical-control installation that requires this style of top-mount control.
Mercury Rigging Fitment
Unlike many engine components, a remote control is better identified by the rigging system than by a broad engine horsepower or year range.
| Fitment Requirement | Required Configuration |
|---|---|
| Rigging System | Compatible Mercury mechanical-control system |
| Electrical Connection | Mercury 14-Pin |
| Throttle Cable | Mercury Gen 2-Style Mechanical Control Cable |
| Shift Cable | Mercury Gen 2-Style Mechanical Control Cable |
| Mounting Configuration | Top / Console / Binnacle Mount |
| Control Type | Mechanical Throttle and Shift |
| Matching OEM Numbers | 8M4507538, 8M0059686, 8M0041431, 883711A12 |
Check Your Existing Control Before Ordering
Mercury has used multiple generations and styles of remote controls. Two controls may look similar from the helm while using different electrical connectors or control cables underneath the console.
- 14-Pin: Verify the existing electrical connection matches the required Mercury 14-pin configuration.
- Gen 2 Cables: Confirm the boat uses compatible Mercury Gen 2-style mechanical throttle and shift cables.
- Top Mount: This is for a console / binnacle-style top-mount installation.
- Mechanical Control: Do not assume compatibility with a digital electronic throttle and shift system.
- Original Part Number: Whenever possible, compare the part number from the original control with the cross references on this page.
Pro Marine 8M0059686P Binnacle Top Mount Control
Looking for an aftermarket alternative? Pro Marine USA also stocks the Pro Marine 8M0059686P binnacle / top-mount control for the compatible Mercury 14-pin and Gen 2 cable application.
Common Replacement Reasons
- Original Mercury binnacle control is worn or damaged.
- Control lever operation has become loose, difficult, or unreliable.
- Throttle or shift operation is no longer functioning correctly.
- Control housing or lever has been physically damaged.
- Existing control is being replaced during a helm restoration or re-rig.
- An older matching Mercury control number is being replaced with the current stocked version.
Problems with throttle or shift operation can also be caused by worn, damaged, incorrectly adjusted, or binding control cables. Inspect the complete control and cable system before replacing components.
Installation Tips
- Disconnect battery power before servicing the remote-control electrical system.
- Confirm the existing harness uses the correct Mercury 14-pin connection.
- Verify both throttle and shift cables are the correct Gen 2-style cables.
- Inspect existing cables for corrosion, stiffness, kinks, or excessive wear.
- Compare the new control with the original before changing the console opening or cable routing.
- Avoid sharp cable bends that can increase control effort or cause binding.
- Verify correct shift direction, neutral position, throttle travel, and overall control operation after installation.
Because the remote control directly affects engine throttle and shift operation, installation and adjustment should be performed by a qualified marine technician when the installer is not familiar with Mercury mechanical rigging systems.
Key Features and Benefits
- Genuine Mercury OEM: Factory Mercury remote-control assembly.
- Top Mount Design: For compatible console and binnacle-mount installations.
- 14-Pin Application: Designed for the compatible Mercury 14-pin electrical configuration.
- Gen 2 Cable Application: Uses compatible Mercury Gen 2-style mechanical control cables.
- Mechanical Throttle and Shift: Designed for cable-operated Mercury rigging systems.
- Multiple Cross References: Associated with 8M0041431, 8M0059686, and 883711A12.
- Aftermarket Alternative: Pro Marine 8M0059686P is also available.
Frequently Asked Questions
What is Mercury 8M4507538?
8M4507538 is a genuine Mercury OEM console / binnacle top-mount remote control for compatible Mercury mechanical rigging systems using a 14-pin connection and Gen 2-style control cables.
What control cables does Mercury 8M4507538 use?
This application uses Mercury Gen 2-style mechanical throttle and shift control cables.
Does Mercury 8M4507538 use a 14-pin connector?
Yes. This listing is for the compatible Mercury 14-pin electrical configuration.
Is 8M4507538 a top-mount or side-mount control?
It is a top / console / binnacle-mount control.
Does 8M4507538 replace 8M0059686?
8M0059686 is one of the Mercury OEM cross-reference numbers supplied for this control application.
Does it cross-reference Mercury 8M0041431?
Yes. 8M0041431 is included among the supplied Mercury OEM references for this control.
What about Mercury 883711A12?
883711A12 is also included among the supplied cross references for this compatible control application.
Will this fit every Mercury outboard?
No. Fitment is based on the rigging configuration, not simply engine brand or horsepower. The installation must use the compatible Mercury 14-pin electrical system and Gen 2 mechanical control cables.
Will this replace an 8-pin Mercury control?
Do not assume so. This listing is for a 14-pin application. An 8-pin system uses a different electrical configuration and should be identified before ordering a replacement control.
Can I use this with Gen 1 control cables?
This control is listed for Gen 2-style control cables. A Gen 1 cable installation should not be assumed to be directly compatible.
Is this a digital throttle and shift control?
No. This application uses mechanical Gen 2-style throttle and shift control cables.
Is an aftermarket version available?
Yes. Pro Marine USA also stocks the Pro Marine 8M0059686P binnacle top-mount control for the compatible application.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 continental U.S.
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1-5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Parts must be new, unused, and in original packaging.
- Installed parts are not returnable.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers
8M4507538, 8M0041431, 8M0059686, 883711A12, 8M0059686P, 8M 4507538, 8M 0041431, 8M 0059686, 883711 A12
Searchable Terms
Mercury OEM binnacle control, Mercury top mount control, Mercury console control, Mercury 14 pin control, Mercury 14-pin remote control, Mercury Gen 2 control, Mercury Gen 2 control box, Mercury Gen 2 cable control, Mercury mechanical throttle control, Mercury mechanical shift control, Mercury throttle and shift control, Mercury console mount remote, Mercury binnacle remote, 8M4507538 remote control, 8M0059686 replacement, 8M0041431 replacement, 883711A12 replacement
8M0059686
8M4507538
883711A12
67F-11325-01-00
804079
804079001
804085A01
887847A01
8M0059686P Mercury 14-Pin Gen 2 Binnacle Top Mount Control
The Pro Marine 8M0059686P Binnacle / Top Mount Control is an aftermarket remote control for compatible Mercury rigging systems using a 14-pin electrical connection and Gen 2-style mechanical control cables.
Designed for console and binnacle-mount installations, this control is an aftermarket replacement option for Mercury control numbers including 8M0041431, 8M0059686, 8M4507538, and 883711A12.
Product Information
- Pro Marine Part Number: 8M0059686P
- Brand: Pro Marine
- Part Type: Binnacle / Top Mount Remote Control
- Application: Compatible Mercury Rigging Systems
- Electrical Connection: 14-Pin
- Control Cable Type: Mercury Gen 2 Style
- Mounting Style: Top / Console / Binnacle Mount
- OEM Alternative: Mercury 8M4507538
Important Fitment Note
Control boxes should not be ordered by engine horsepower alone. Mercury used different electrical connector styles and different mechanical control-cable generations across its rigging systems.
This control is specifically for compatible applications requiring a 14-pin electrical connection and Mercury Gen 2-style control cables.
Verify the connector style, cable type, mounting arrangement, and original control-box part number before ordering. A Mercury control using an 8-pin connection, Gen 1 cables, digital controls, or another rigging configuration requires a different control.
OEM and Cross Reference Numbers
Pro Marine 8M0059686P cross-references the following Mercury remote-control numbers for the compatible 14-pin / Gen 2 control application.
| Part Number | Brand / Relationship |
|---|---|
| 8M0059686P | Pro Marine Aftermarket |
| 8M0041431 | Mercury OEM Cross Reference |
| 8M0059686 | Mercury OEM Cross Reference |
| 8M4507538 | Mercury OEM Version Stocked by Pro Marine USA |
| 883711A12 | Mercury OEM Cross Reference |
Mercury OEM 8M4507538 Remote Control
Prefer genuine Mercury OEM? Pro Marine USA also stocks Mercury 8M4507538, the OEM console / top-mount control for the corresponding Gen 2 cable application.
What This Control is Used For
The binnacle control provides the operator interface for throttle and shift operation on compatible Mercury mechanical-control installations.
This style of control mounts at the helm or console and connects to the engine rigging system using the required Mercury electrical connection and mechanical control cables.
It is commonly used when replacing a worn or damaged remote control, restoring an existing Mercury rigging system, or re-rigging a boat that is already configured for the corresponding Mercury 14-pin and Gen 2 cable system.
Compatible Applications
Fitment for this control is determined primarily by the rigging configuration, not a simple horsepower or model-year range.
| Fitment Requirement | Required Configuration |
|---|---|
| Engine / Rigging Brand | Compatible Mercury mechanical-control system |
| Electrical Connection | 14-Pin Mercury configuration |
| Control Cable Type | Mercury Gen 2 Style Control Cables |
| Mounting Style | Top / Console / Binnacle Mount |
| Cross-Reference Match | 8M0041431, 8M0059686, 8M4507538, or 883711A12 application |
Verify Before Replacing Another Mercury Control
Mercury control boxes can look similar while using different rigging systems. This part should not automatically be substituted for a control that uses a different connector or cable generation.
- Do not substitute for an 8-pin control without verifying the complete rigging system.
- Do not substitute for a Gen 1 cable control unless the rigging is being properly converted.
- Do not use as a replacement for a digital electronic throttle and shift control.
- Verify whether the installation requires a single- or multiple-engine control configuration.
- Compare the original Mercury control-box number whenever possible.
Common Replacement Reasons
- Existing binnacle control has excessive wear or internal damage.
- Throttle or shift lever operation has become unreliable or difficult.
- Control housing or lever has been physically damaged.
- Existing control is being replaced during a Mercury re-rig or helm restoration.
- An older matching Mercury OEM control number is being replaced.
- The boat requires a compatible 14-pin top-mount control using Gen 2 cables.
Installation Tips
- Disconnect battery power before servicing the remote-control or engine electrical system.
- Confirm the existing electrical connector is the correct Mercury 14-pin configuration.
- Verify that the installed throttle and shift cables are Mercury Gen 2-style cables.
- Compare the new control with the original unit before modifying the console or cable routing.
- Inspect control cables for stiffness, corrosion, damage, or excessive wear before reconnecting them.
- Route cables without sharp bends or binding that could interfere with throttle or shift movement.
- After installation, verify correct shift direction, neutral position, throttle travel, and control operation before operating the boat.
Remote-control installation affects throttle and shift operation. Installation and adjustment should be performed by a qualified marine technician if you are not familiar with Mercury mechanical rigging systems.
Key Features and Benefits
- Pro Marine Brand: Aftermarket alternative to the corresponding Mercury OEM control.
- Top Mount Design: Designed for binnacle / console-mounted helm installations.
- Mercury 14-Pin: For compatible Mercury 14-pin electrical rigging systems.
- Gen 2 Cable Compatible: Designed for Mercury Gen 2-style mechanical control cables.
- Multiple OEM Cross References: Cross-references 8M0041431, 8M0059686, 8M4507538, and 883711A12.
- OEM Version Available: Genuine Mercury 8M4507538 is also stocked by Pro Marine USA.
Frequently Asked Questions
What is Pro Marine 8M0059686P?
8M0059686P is a Pro Marine aftermarket binnacle / top-mount remote control for compatible Mercury 14-pin rigging systems using Gen 2-style mechanical control cables.
What type of control cables does 8M0059686P use?
It is designed for Mercury Gen 2-style control cables.
What electrical connection does this control use?
This control is listed for a Mercury 14-pin electrical connection.
Is this a side-mount control?
No. This is a binnacle / top-mount console control.
Does 8M0059686P replace Mercury 8M0059686?
Yes. Mercury 8M0059686 is one of the OEM cross-reference numbers listed for Pro Marine 8M0059686P.
Does it replace Mercury 883711A12?
883711A12 is also listed as a cross reference for this compatible control application.
Is Mercury 8M4507538 the OEM version?
Yes. Pro Marine USA stocks Mercury 8M4507538 as the genuine Mercury OEM console / top-mount control option.
Will this fit every Mercury outboard?
No. Compatibility depends on the boat's Mercury rigging system. The application must use the compatible 14-pin connection and Gen 2-style mechanical control cables.
Will this replace an 8-pin Mercury control?
Not as a direct replacement based only on appearance. This control is for the compatible 14-pin system. Verify the complete rigging configuration before changing control types.
Will it work with Mercury Gen 1 control cables?
This listing is specifically for a Gen 2-style control cable application. A Gen 1 cable system should not be assumed compatible.
Is this for digital throttle and shift?
No. This listing is for a control using mechanical Gen 2-style throttle and shift control cables.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 continental U.S.
- Orders ship via UPS, USPS, and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1-5 business days.
30-Day Return Policy
- Returns accepted within 30 days of delivery.
- Parts must be new, unused, and in original packaging.
- Installed parts are not returnable.
- Return authorization is required before sending items back.
Need help with a return or order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers
8M0059686P, 8M0041431, 8M0059686, 8M4507538, 883711A12, 8M0041431P, 8M0059686P, 883711A12 replacement
Searchable Terms
Mercury binnacle control, Mercury top mount control, Mercury console control, Mercury 14 pin control, Mercury 14-pin binnacle, Mercury Gen 2 control, Mercury Gen 2 control box, Mercury Gen 2 cable control, Mercury throttle control, Mercury shift control, Mercury mechanical remote control, Mercury console mount remote, 8M0059686 replacement, 8M0041431 replacement, 8M4507538 replacement, 883711A12 replacement, Pro Marine 8M0059686P
8M0059686
8M4507538
883711A12
Low-Pressure Fuel Pump for Suzuki DF200-350 and DT115-225
Pro Marine 94900P is an aftermarket low-pressure electric fuel pump for select Suzuki four-stroke and two-stroke outboards, as well as select Johnson and Evinrude four-stroke models. It replaces Suzuki OEM number 15100-94900 and Johnson/Evinrude number 5035394.
Low-Pressure Fuel Supply Pump
This pump supplies fuel to the engine's vapor separator tank, commonly called the VST. The separate high-pressure electric pump located inside the VST then supplies pressurized fuel to the fuel-injection system.
This listing is for the low-pressure supply pump. It is not the electric pump installed inside the VST.
OEM & Cross Reference Numbers
| Brand | OEM / Reference Number |
|---|---|
| Suzuki | 15100-94900 |
| Johnson / Evinrude | 5035394 |
| Pro Marine | 94900P |
Compatible Suzuki Four-Stroke Outboards
| Model Family | Listed Years / Production Groups |
|---|---|
| DF200 | 2004–2010, 2013 and 2015; DF200T and DF200Z 2004–2007; listed production groups including -51001, 710001 and 20002, 22503, 25003 and 25004 F/Z serial-prefix applications |
| DF225 | 2004–2010, 2013 and 2015; DF225T and DF225Z 2004–2007; listed production groups including -51001, 710001 and 20002, 22503, 25003 and 25004 F/Z serial-prefix applications |
| DF250 | 2004–2010, 2013 and 2015; DF250T and DF250Z 2004–2007; listed production groups including -51001, 710001 and 20002, 22503, 25003 and 25004 F/Z serial-prefix applications |
| DF250A | 2013 and 2015; listed -310001, -510001 and 710001 production groups |
| DF300 | 2007–2010 |
| DF300A | 2013 and 2015; listed -310001, -510001, 30002P-210001 and 710001 production groups |
| DF350A | Serial number 810001 and later listed applications |
Compatible Suzuki Two-Stroke Outboards
| Model | Listed Years |
|---|---|
| DT115 | 1986–2001 |
| DT140 | 1986–2001 |
| DT150 | 1998–2003 |
| DT200 | 1998–2003 |
| DT225 | 1998–2003 |
Johnson / Evinrude Fitment
Replaces Johnson/Evinrude OEM number 5035394 on the following listed 200 and 225 HP four-stroke model numbers:
Important Fitment Note
Suzuki reused model names across multiple years and production ranges. Match the OEM number removed from the engine whenever possible.
Before ordering, verify that your application calls for Suzuki 15100-94900 or Johnson/Evinrude 5035394. Do not select this pump based only on horsepower.
What This Fuel Pump Is Used For
The low-pressure pump draws fuel from the boat's fuel supply and delivers it to the engine's VST. A properly operating supply pump helps keep the VST filled so the internal electric pump can maintain fuel delivery to the injectors.
A worn or failing low-pressure fuel pump may contribute to fuel starvation, hesitation, loss of power under load, difficult starting or an engine that runs normally at lower speed but struggles as fuel demand increases.
Key Features & Benefits
Pro Marine replacement for Suzuki 15100-94900 and Johnson/Evinrude 5035394.
Supplies fuel from the boat's fuel system to the vapor separator tank.
Fits listed Suzuki DF200 through DF350A and DT115 through DT225 applications.
Fits the specifically listed Johnson and Evinrude 200 and 225 HP four-stroke model numbers.
Need the Electric Pump Inside the VST?
The pump on this page supplies low-pressure fuel to the VST. The related pump below is the electric fuel pump installed inside the vapor separator tank on applicable engines.
Frequently Asked Questions
Is this the fuel pump located inside the VST?
No. Item 94900P is the low-pressure supply pump that sends fuel to the VST. The related item 8808 is the electric pump installed inside the VST on applicable engines.
Does this replace Suzuki 15100-94900?
Yes. Pro Marine item 94900P is an aftermarket replacement for Suzuki OEM fuel-pump number 15100-94900.
Does this replace Johnson/Evinrude 5035394?
Yes. It cross-references to Johnson/Evinrude number 5035394 for the specifically listed four-stroke model numbers.
Does this fit every Suzuki DF200, DF225 or DF250?
No. Fitment depends on the engine year, model designation and production range. Verify OEM number 15100-94900 before ordering.
Is this an OEM Suzuki pump?
No. This is a Pro Marine aftermarket replacement pump.
Dealer Discounts & Store Policies
Dealer / Marine Industry Discounts
Are you a marine dealer, technician, boat builder, or industry professional? We offer dealer pricing for qualified marine businesses.
Shipping Policy
- Free shipping on orders over $100 in the continental U.S.
- Orders ship via UPS, USPS and FedEx.
- Orders received before 5:30 PM EST ship the same business day.
- Typical delivery time is 1–5 business days.
30-Day Return Policy
- Returns are accepted within 30 days of delivery.
- Parts must be new, unused and in their original packaging.
- Installed parts are not returnable.
- Return authorization is required before sending items back.
Need help confirming fitment or have an order question?
Contact Us
Phone: 941-721-3000
Searchable Part Numbers & Applications
94900P, 15100-94900, 5035394, Suzuki low-pressure fuel pump, Suzuki DF200 fuel pump, DF225 fuel pump, DF250 fuel pump, DF250A fuel pump, DF300 fuel pump, DF300A fuel pump, DF350A fuel pump, DT115 fuel pump, DT140 fuel pump, DT150 fuel pump, DT200 fuel pump, DT225 fuel pump, Johnson 200 four-stroke fuel pump, Johnson 225 four-stroke fuel pump, Evinrude 200 four-stroke fuel pump, Evinrude 225 four-stroke fuel pump
5035394
395540
5004610
5004610
0331363
0338876
0777739
18-2879
312634
312634
33110
331363
338876
777739
802303
0765563
331188
765563
81250